FUFU & GAGA ZSJJ22019 User manual

Version:09/23/2022 1/15
Display Stand

2/15
please read the entire manual before starting to assemble
and/or using this product.follow the manual thoroughly and
keep it for further reference.
IMPORTANT INFORMATION!
It is important that any product which is assembled using any kind of screw is re-tightened
2 weeks after assembly,and once every 3 months - in order to assure stability through-out
the lifespan of the product.
For regular maintenance and cleaning of the product, for the frame, please use a rag dipped
in neutral detergent to fully wipe it, and then dry it with a clean rag.For glass materials, wipe
with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because
the board is easy to break.
IMPORTANT !
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure
to use the wall attachment, if not included with this product. Please purchase the wall
attachment that fit your wall. If unsure, seek professional advice. Please read and follow each
step of the instructions carefully.
ANTI-TOPPLE WARNING !
Try to find a partner to install
with you, which can speed up
the installation efficiency and
shorten the time.
IMPROVE EFFICIENCY !
In order to avoid scratching this
furnuture should be assembled
on a soft layer-could be a rug.
AVOID SCRATCHES!

3/15
Ax6
Ø6x35mm
Ø4x14mm
Bx6
Ø15x10mm
Cx22
Ø6x30mm Ø4x40mm
Dx20
Ex24 Fx4 Gx2 Hx8
Ix8 Jx2 Kx2 Lx2
Please prepare the following tools
When installing, please carefully confirm whether
each screw corresponds to the manual, accessories
with similar shapes can be distinguished by size
K-1 K-2 K-3J-1 J-2 J-3
Ø3x12mm
G-1 G-2
Mx24(+2) Nx16(+1) Ox5

4/15
1
2
3
5
6
4
4
7
8
9
11
12
13
10
14

5/15
1Ax2
2
Ø6x35mm
A
9
A
A
C
C
B
B
9
10
Bx2 Cx2
Ø15x10mm Ø6x30mm
IIIIII
C
B
Insert quickfit screw(A) into
corresponding holes in No.9
plate with a screwdriver as
shown.
Connect No.10 with No.9 plate using
wooden dowel(C) and turn cam lock(B)
clockwise to tighten as shown.

6/15
3
4
Cx2
Ø6x30mm
Dx4
Ø4x40mm
Nx4
D
D
C
C
D
N
DN
N
N
D
9
10
8
N
DD
D
DC
C
DN
N
N
N
N
9
10
7
Cx2
Ø6x30mm
Dx4
Ø4x40mm
Nx4
Connect the component with No.8 plate using
wooden dowel(C), and fix with screw(D) as
shown.
Connect No.7 plate with the component
using wooden dowel(C), and fix with
screw(D) as shown.
Use sticker(N) to cover screws.

7/15
5
9
10
8
7
6Cx2
Ø6x30mm
Dx2
Ø4x40mm
Nx2
D
N
C
C
N
5
3
O
O
O
O
O
O
D
N
Ox5
Knock foot peg(O) into the bottom
as shown.
Connect No.5 plate with No.3 using wooden dowel(C),
and fix with screw(D) as shown.
Use sticker(N) to cover screws.

8/15
7Cx2
Ø6x30mm
Dx2
Ø4x40mm
Nx2
D
D
C
C
N
N
8Ax4
Ø6x35mm
D
N
5
2
A
A
A
A
A
6
Connect No.2 plate with No.5 using wooden dowel(C),
and fix with screw(D) as shown.
Use sticker(N) to cover screws.
Insert quickfit screw(A) into
corresponding holes in No.6plate
with a screwdriver as shown.

9/15
9
10
D D
D
D
D
C
C
C
C
2
3
6
Cx4
Ø6x30mm
Dx4
Ø4x40mm
Cx4
Ø6x30mm
Dx4
Ø4x40mm
Nx4
D
N
D
D
D
N
N
C
C
C
C
N
2
3
1
D
N
Attach No.6 to No.2 and No.3 plate using
wooden dowel(C) and fix with screw(D) as
shown.
Cover No.1 to No.2 and No.3 plate
using wooden dowel(C) and fix
with screw(D) as shown.
Use sticker(N) to cover
screws.

10/15
11
Bx4 Cx4
Ø15x10mm Ø6x30mm
C
B
B
C
CC
B
B
6
7
8
IIIIII
C
B
Connect the two assembled components
with wooden dowel(C) and turn cam lock(B)
clockwise to tighten as shown.
Recommend more than 2
people to assemble!