Tenda F303 Setup guide

How to setup universal repeater mode for F303
Part 1: Login the homepage of the router
Part 2: Setup LAN IP
Part 3: Enable universal repeater mode
Part 4: Verify bridge connectivity
Part 5: Setup secondary SSID and security key
The Topology is as below:
!

Steps are as following:
!
1. Login to the management page of the router.
!
2. Input login username and password as admin, to login, then click Advanced.
!

!
!
1. Click Network, and then click LAN. Change your router’s LAN IP.(The LAN IP address should
bedifferent. For example, the uplink router has the LAN IP 192.168.0.1, then you can set the
secondary router’s LAN IP as 192.168.0.10)

!
!
1. Click Wireless and then choose Wireless Extender, choose Universal Repeater mode. Click Open Scan.

!
2.Select your uplink router’s SSID, and input your uplink router’s security key. then click Save to
save the settings.

!
!

1.Connect your PC to this Tenda wireless router via a wired or wireless!
connection and set it to "Obtain an IP address automatically". If you are not clear, see Appendix
1 Configure PC TCP/IP Settings .
2.Wait until your PC successfully obtains an IP address.
!
3.Click Start ->RUN;

!
4. Enter cmd and click OK.
!

5. Enter "ping default gateway IP address”. Here in this example, enter "ping!
192.168.0.1" and press Enter. If you see a similar screen (highlighted area), the bridge is
established successfully.
!
Note: After finish the universal repeater settings, the factory SSID will become secondary
SSID automatically.

!
5.1 Click Wireless and Wireless Basic Setting, change secondary SSID, and then click OK to
save the settings.
!
5.2 Setup the security key
Click wireless security key, select SSID which you have set as secondary SSID, choose the security
mode as WPA-PSK, input your security key, and click OK to save the setting.

!
Notice：If you have other PC need to be get connected, please connect it to the one of the LAN
port or the wireless signal of the router. There is no need to configure the router again.

Function configurations How to setup WISP mode for F303
2015/5/19 Clicks：15!!!
Product line: wireless question category: function config
Part 1: Login the homepage of the router
Part 2: Setup connection type and LAN IP
Part 3: Enable WISP mode
Part 4: Setup secondary SSID and security key
The Topology is as below:
!
Steps are as following:

!
1. Login to the management page of the router.
!
2. Input login username and password as admin, to login, then click Advanced.
!
!

!
1.Click Advanced, then click Internet connection setup. Choose DHCP, click Save.
!

2. Click Advanced, and then click LAN Settings. Change your router’s LAN IP.(The LAN IP address
should be in different network segment. For example, the uplink router has the LAN IP
192.168.0.1, then you can set the secondary router’s LAN IP as 192.168.10.1.)
!
!
1. Click Wireless and then choose Wireless Extender, choose WISP mode. Click Open Scan.

.!
2.Select your uplink router’s SSID, and input your uplink router’s security key. then click Save to
save the settings.
!

3.After reboot, if the connection status shows connected and get the gateway of uplink router,
it means that you can have internet.
!
Note: After finish the WISP settings, the primary SSID will become secondary SSID
automatically.
!
4.1 Click Wireless and Wireless Basic Setting, change secondary SSID, and then click OK to
save the settings.

!
4.2 Setup the security key
Click wireless security key, select SSID which you have set as secondary SSID, choose the security
mode as WPA-PSK, input your security key, and click OK to save the setting.

!
Notice：If you have other PC need to be get connected, please connect it to the one of the LAN
port or the wireless signal of the router. There is no need to configure the router again.

F303-How to setup the router for Static IP internet connection mode
2013/12/21 Clicks：2135!!!
How to setup the router for Static IP internet connection mode
Model number: F303
There are three internet connection modes for the router. This article will guide you how to
setup the router for Static IP mode and the steps as below.
Note: If you have no idea about what is the internet connection type and the accounts
please call your ISP for help.
Part 1:Connect the devices
Part 2: Configure your computer
Part 3: Setup the router
Part 4:Check whether you can access internet
!
Connect the modem with the WAN port of the router, and then connect your computer with
one of the LAN ports by a cable.
!
Note: after connection the SYS light should be blinking, the WLAN light should be on or
blinking, the WAN light should be on or blinking.