Tendercare Snazzi Pushchair User manual

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 1 of 58 April 2015
Snazzi Pushchair User Manual.docx
Snazzi Pushchair
U SER M ANUAL
This manual covers:
Size 1 and 2 Snazzi Pushchair
IMPORTANT
Please read these instructions carefully
Before using your Snazzi

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 2 of 58 April 2015
Snazzi Pushchair User Manual.docx
Fig 0.1 Open Pushchair (size 1 shown)

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 3 of 58 April 2015
Snazzi Pushchair User Manual.docx
Fig 0.2 Folded Pushchair (size 1 shown)

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 4 of 58 April 2015
Snazzi Pushchair User Manual.docx
Item Description Page
1
Who to contact if you have difficulty 6
2
Introduction 6 - 8
3
Unpacking 8 - 9
4
Preparing the pushchair for use 9
4.1.1 Unfolding and Folding 10 - 11
4.2 Brakes & Tyres 12 - 13
4.3 Using the Tilt in Space facility 13 - 14
5
Setting up the seat unit 15
5.1 Adjusting the seat unit 16
5.1.1 Seat Depth and Hip Guides 16
5.1.2 Footrest Depth and Knee Angle Adjustment 16 - 17
5.1.4 Lateral Supports (Optional) 17 - 18
5.2 Fitting and removing the cover 19 - 20
5.3 Fitting a Headrest Pad or Lateral Head Supports (optional) 21 - 22
5.4 Fitting the Pelvic Strap / 4 Point hip belt 22 - 24
5.6 Fitting a Butterfly/Chest Harness or H-Belt Harness (optional) 25 - 27
6
Accessories 28 - 34
6.1 Pommel 28 - 29
6.2 Equipment Carrying Tray 29
6.3 Shopping Basket 30
6.4 Sun hood and transparent rain shield 31 - 36
6.4b Removing the cover for washing 37 - 38
6.5 Playtray 39 - 42
6.6 Ramped Seat Pad 43
6.7 Grip Rail 43 - 44
6.8 Foot Muff 44 - 46
6.9 Ankle Huggers 46 - 47
7
User Instructions 48
7.1 Getting into the Snazzi Pushchair 48
7.2 Getting out of the Snazzi Pushchair 48
8
Attendant pushing 48
8.1 Pushing 48 – 49
8.2 Brakes 49
8.3 Comfort 50
8.4 Lifting and general safety 50
9
Cleaning 51
9.1 Pushchair 51
9.2 Seat Cover 51
9.3 Pelvic strap & harnessing 51

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 5 of 58 April 2015
Snazzi Pushchair User Manual.docx
10
Maintenance 51
10.1 Routine maintenance 51
10.2 Six-monthly maintenance 52
11
Oxygen Cylinder 53
12
Warranty 53
13
Transporting the Pushchair 54
13.1 Preparing the pushchair for transport 54 - 56
13.2 Attaching pushchair to vehicle 56 – 58
14
Repairs 58

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 6 of 58 April 2015
Snazzi Pushchair User Manual.docx
1: Who to contact in difficulty
Tendercare Ltd.
PO BOX 3091, Littlehampton, BN16 2WF
Tel: [phone] Fax: [phone]
Email: [email protected]
Web: www.tendercareltd.com
2: Introduction
The Snazzi is a highly adjustable pushchair designed to accommodate a wide variety of
special seating needs. The pushchair is a single complete unit that folds down for easy
storage. The Snazzi is available in 2 sizes.
The pushchair is made of a strong and lightweight aluminium alloy, minimising weight and
providing a very rugged frame. The Snazzi features a 10
o
to 40
o
infinitely adjustable tilt in
space facility and has 2 fixed rear wheels and 2 swivelling front castors for easy
manoeuvring.
The integrated seat unit offers exceptional growth, thanks to its versatile design and large
range of adjustment to all supports. It has an easy to remove, breathable cover, and
comes supplied with a hip belt as standard.
Seat adjustments (please see table below for details of adjustment ranges): Seat depth
adjustment, width adjustable Hip Guides, 5
o
back recline adjustment (90
o
and 95
o
fixed
positions) large fixed back height with a range of harnessing positions, and depth & angle
adjustable Footrest.
The following accessories for use with the Snazzi Pushchair are available from Tendercare
Ltd.
Equipment carrying tray, Shopping basket, Sun / Rain-hood, Transparent Rain Shield,
Fixed Lateral Supports, Height and width adjustable wrap around Lateral Supports,
Butterfly chest harness, ‘H’ harness, Foot and Toe Straps, Pommel, Play Tray, Lateral
Head Supports, Standard Headrest, Extra recess Headrest, and Occipital roll Headrest.
These instructions apply to all sizes.
A child’s safety is your responsibility. As such we recommend that you read the
complete user manual prior to using your pushchair.

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 7 of 58 April 2015
Snazzi Pushchair User Manual.docx
Snazzi Pushchair Adjustments
Support Snazzi Pushchair Size 1 Snazzi Pushchair Size 2
Tilt
i
n Space
10
o
- 40
o
10
o
- 40
o
Se
at Depth
220 – 300 mm 280 – 360 mm
Seat Width
190 – 290 mm 190 – 290 mm
Backrest Height
600 mm fixed 670 mm fixed
Footrest Depth
172 – 300 mm 172 – 320 mm
Back Recline Angle
90° or 95
o
90
o
or 95
o
Knee Angle*
-15°- 90° -15°- 90°
Pushchair
Weight
14Kg 15Kg
Maximum Carry Weight
**
35Kg 35Kg
IMPORTANT:
* Knee angle adjustable in 15° increments
** Maximum carry weight includes the occupant and all accessories.
Snazzi Pushchair (Open) Dimensions (mm)
Size 1 Size 2
A
780 863
B
607 607
C
1069 1155
A
B
C

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 8 of 58 April 2015
Snazzi Pushchair User Manual.docx
Snazzi Wheelbase Folded Dimensions (mm)
Size 1 Size 2
A
802 875
B
607 607
C
402 420
All sizes and weights are given as a guide. Tendercare ltd reserves the right to amend
specifications at any time as part of their product development programme.
3: Unpacking
The pushchair is delivered in a cardboard carton. This measures 680mm wide x 480mm
deep x 1030mm high and weighs approximately 16Kg (size 1) or 17Kg (size 2).
WARNING:
The transit carton is quite bulky so moving and unpacking must be done with care.
Observe all lifting and handling regulations.
Stand the carton upright making sure it is supported and cannot fall over. Open the carton
and remove any packages or packing, which could obstruct the removal of the pushchair.
Remove the pushchair.
The carton should contain the following items:
Item Component QTY. Yes No
1
Size 1 or 2 Pushchair 1
2
User Manual 1
3
5mm Alan key 1
The following items should be fitted to the seat as standard:
Item Component QTY. Yes No
4
Hip guide covers 2
5
Seat Base Cover 1
6
Seat Back Cover 1
7
Hip Belt 1
Please note, accessories such as lateral supports or harnessing that were ordered at the
same time as the pushchair will be included in the main package.
C
A
B

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 9 of 58 April 2015
Snazzi Pushchair User Manual.docx
Larger accessories will be packaged in separate cartons (e.g. the rain cover).
IMPORTANT:
 If any items are damaged or missing, then please contact Tendercare, preferably by email at
[e-mail] or alternatively please call us on [phone] within 36 hours of
delivery.
After unpacking and checking you have all components and they are in good condition
dispose of the packaging at your local recycling centre. Alternatively retain and reuse.
4: Preparing the Pushchair for use
WARNING:
When opening or folding the pushchair, ensure that you hold the frame so that you
avoid any danger of catching your fingers in moving parts.
Keep children clear of the pushchair during opening and folding.

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 10 of 58 April 2015
Snazzi Pushchair User Manual.docx
4.1 Unfolding and Folding the Snazzi
Standing at back of the pushchair, hold the
push handle (X fig 4.1.1) and lift up. When the
frame is about half way up, place your foot on
the rear cross bar and pull it towards you.
This will open the frame.
Fig 4.1.1
Fig 4.1.2
Once the frame is almost open, the 2
plastic frame locks will engage with the
angled sections of the lower frame.
Continue to unfold the frame; this will force
the locks up the tubes. There will be some
resistance, as you will be working against
the locking springs.
Once fully open, the frame locks will snap
shut over the rear frame lock points, securing
the frame in the open position.
Always check that both locks are fully closed.
In the locked position the guide bolt ‘B’ will be
sat in the top of the slot ‘A’ on the side of the
slider as shown (see Fig 4.1.3). If there is any
slot visible above the guide bolt, push the lock
down by hand until it will not move any
further.
Fig 4.1.3
X
A
B

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 11 of 58 April 2015
Snazzi Pushchair User Manual.docx
Fig 4.1.4
The Snazzi includes a safety catch to
prevent accidental folding of the chair in the
event that both spring-loaded locking
sliders did not engage fully when unfolding.
The catch also helps reduce any small
amount of movement in the frame when set
up, improving comfort for the occupant.
This is located near the bottom of the seat
back as shown (see fig 4.1.4).
Definition of components:
X: Pull handle
Y: Locking Point
To lock the catch, pull “X” and turn 90 degrees,
then push in so that pin is fully protruded and is
visible in the locking point “Y” (see Fig 4.1.5).
To release the catch, pull the handle “X”, and
turn it 90 degrees in the opposite direction so
that the pin “Y” is fully retracted.
Fig 4.1.5
Fig 4.1.6
To fold the frame:
Release the safety catch (see Fig 4.5.1).
Standing behind the frame, place your foot
on the rear cross bar, and pull up the 2
locking sliders as shown (see Fig 4.1.2).
Whilst holding the locks open, lift the frame
slightly until the locks are clear from the
locking points on the lower frame.
Then take hold of the push handle and fold
the frame down fully.
IMPORTANT:
Always check that BOTH frame locks are fully closed before using the frame. If they
are not properly engaged, the frame could collapse during use.
X
Y

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 12 of 58 April 2015
Snazzi Pushchair User Manual.docx
4.2 Brakes & Tyres
Fig 4.2.1
To apply the brake, put your foot on the top
of brake bar (labelled X) and push down as
shown. The brake will rotate round against
the wheels and lock in between the wheels
and frame. Do not stand, or use excessive
force, on the brake as this may cause it to
bend.
To release the brake, hook your foot
between the middle raised portion of the
brake bar, and the frame cross bar. Then,
lift the brake bar with your foot until it flips
back and stops against the brake stop
points. Please note you may find it easier
to use your hand to release the brake. If
operating the brake by hand always hold
the brake by the raised section in the
middle of the brake bar.
Important:
Always put the brake on when placing the
child in, or taking them out of the
pushchair.
Do not leave the brake on when the
pushchair is not in use as this will damage
the rear wheels.
Fig 4.2.2
WARNING:
The brake mechanism is spring loaded so care must be taken when operating it.
When operating the brake mechanism ensure that you always keep a firm hold of
the pushchair, keeping your hands well away from the brake mechanism.
Care must be taken when applying the brake, as applying excessive force, or
standing on the brake may cause it to bend.
Do not leave the pushchair on a slope, even with the brake on. Always ensure that
the pushchair is on level ground to prevent risk of injury to the occupant.
X

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 13 of 58 April 2015
Snazzi Pushchair User Manual.docx
Tyres:
As standard the Snazzi pushchair is supplied with solid tyres, however pneumatic tyres are
also available as an option. If your pushchair is supplied with pneumatic tyres these need
to be regularly checked and inflated if necessary using a hand or foot pump. The operating
pressure for the tyres is 36 PSI (note: do not inflate the tyres above 36 PSI). Do not use
high pressure air lines or mechanical pumps as used in garages to inflate the tyres.
4.3 Using the Tilt in Space facility
Fig 4.3.1
To operate the Tilt in Space mechanism,
take hold of the push handle with one hand
and push / pull (*depending on model) the
lever on the gas spring at the back of the
seat with your other hand as shown (see fig
4.3.1).
* Note 1: For Snazzi pushchairs purchased
before April 2015, the handle may push
down. All pushchairs purchased after this
date pull the handle up.
Move the seat into the desired position, and
then release the lever to lock the seat in this
position.
Fig 4.3.2

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 14 of 58 April 2015
Snazzi Pushchair User Manual.docx
Fig 4.3.3
To reset the tilt mechanism, push (*or pull
please see Note 1) the lever and push
handle as shown (see Fig 4.3.3). Once in
the desired position, release lever. For a 90-
degree position, move the seat so the gas
strut is fully open and it will not move any
further before releasing the tilt lever.
IMPORTANT:
 Always ensure any harness provided for the child is used and correctly adjusted before
reclining or returning the seat to a more upright position.
 Always support the seat when tilting, as the gas springs can be quick to operate. If the seat is
not supported, it may move swiftly and could cause the occupant distress.

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 15 of 58 April 2015
Snazzi Pushchair User Manual.docx
5.0: Setting up the seat unit
When setting up the seat unit always ensure the following is done:
•Always consult your Therapist or Rehabilitation Engineer for advice.
•Ensure that the child is relaxed and happy and if possible in an environment in
which they are familiar.
•If possible, sit the child on a plinth to take the measurements listed below:
Fig 5.0.1 Definition of measurements
Note: you can now adjust the seat to suit your child’s dimensions
Measurement
Number
(see fig 5.0.1) Millimetres
Top of head to seat 1
Under armpit to seat
(Axilla height) 2
Actual sitting depth 3
Chest Width
(Arm pit to arm pit) 4
Hip width 5
Leg drop 6

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 16 of 58 April 2015
Snazzi Pushchair User Manual.docx
5.1 Adjusting the seat unit
Common adjustments on the Snazzi seat (such as seat depth and width) can be made by
hand and require no tools. Less common adjustments (such as the footrest depth) are
made using a 5mm hexagon key (supplied). No other tools are required to make
adjustments to the seat.
5.1.1 Seat Depth and Hip Guides
Fig 5.1.1.1
To adjust the seat depth and width, first
remove the seat base cover (this is attached
by Velcro in the centre of the seat and is
easily removed by pulling it away from the
frame).
Loosen the 4 thumb wheels under seat as
shown (see fig 5.1.1.2). For easier access
to these the seat base can be hinged up.
Next set the seat width (‘A’ see Fig 5.1.1.1)
as measured in section 5.0 by sliding the
hip guide brackets in or out as required.
To adjust the seat depth (‘B’ see Fig
5.1.1.1), slide the upper of the base plates
forward or back to achieve the required
position.
Once adjusted, tighten the 4 thumb wheels
and fit the cover back into place.
Fig 5.1.1.2
5.1.2 Footrest Depth and Knee Angle Adjustment
Fig 5.1.2.1
To adjust the foot depth, loosen the 2 securing
bolts using the 5mm hexagon key as shown
(see Fig 5.1.2.1).
Slide the footrest up or down the guide tubes
to the required height as measured in section
5.0
Once set, lock the position by tightening the 2
fixing bolts.
A
B

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 17 of 58 April 2015
Snazzi Pushchair User Manual.docx
To adjust the knee angle, press in the
angle adjustors on both sides of the
footrest at the same time (see Fig 5.1.2.2),
and lift the footrest guide tubes to the
required angle. To lock, release the
buttons.
Note that the adjustors can only be locked
in 15° increments.
Fig 5.1.2.2
5.1.3 Lateral Supports (Optional)
Fig 5.1.3.1 (Lateral Trunk Supports with Chest
Belt) Fig 5.1.3.2 (Lateral Trunk Supports)
The lateral trunk supports are supplied
with two M8 coach bolts, and two 30mm
hand wheels per bracket (see Figs
5.1.3.1and 5.1.3.2).
To fit the laterals:
The laterals are fitted by securing with
coach bolts and hand wheels, through
the mounting slots ‘H’ (see Fig 5.1.3.3)
on the back of the seat unit.
Fig 5.1.3.3
H

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 18 of 58 April 2015
Snazzi Pushchair User Manual.docx
Fig 5.1.3.4
The lateral bracket must be fed through the slot
in the cover (see Fig 5.1.3.4).
Next, insert the 2 coach bolts through the
bracket and seat back plate, so that the square
neck is sitting fully in the slots.
Finally, secure the laterals by screwing
the provided hand wheels onto the
protruding threads of the coach bolts
(see Fig 5.1.3.5).
The position of the laterals can be
adjusted laterally by loosening the hand
wheels and sliding them in or out to the
required width.
They can be adjusted vertically by
sliding up and down the mounting slots
‘H’ (see fig 5.1.3.3). There is a partition
in the middle of the slots. To achieve
the full adjustment range, the laterals
need to be fitted in the appropriate
section of the slots.
Fig 5.1.3.5

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 19 of 58 April 2015
Snazzi Pushchair User Manual.docx
5.2 Fitting and removing the cover
Fig 5.2.1
To remove the seat pad:
Simply lift the back edge of the seat pad to
separate it from the Velcro strip on the
base.
To remove the hip guide covers:
The cover hooks around the front of the hip
guide plate. To remove, first undo the
popper at the top corner, lift and rotate the
cover from the rear as shown (see fig 5.2.2),
and then unhook the cover from under the
front of the hip guide plate.
Fig 5.2.2

Snazzi Pushchair User Manual
Document No: 055-02 V12 Page 20 of 58 April 2015
Snazzi Pushchair User Manual.docx
Fig 5.2.3
To remove the back pad, first release the
poppers on the integrated side pads (see fig
5.2.3).
Next un-tuck the back pad from the bottom
of the seat.
Finally remove the back pad by lifting the
top lip off from the backrest board as shown
(see fig 5.2.4).
Fig 5.2.4