Teplo T002 User manual

P.1
teplo
Connected Teapot
Instructions for Use
teplo is a smart teapot which enables a personalized tea brewing experience.
teplo measures your heartrate, finger temperature, and environment conditions
using built in sensors. teplo then adjusts brewing temperature and time based
on your personal information in order to brew tea ideally suited to you.
Please read all instructions carefully before operating the teplo teapot.
Contents
- Know your teplo・・・・・・・ P.2
- Display・・・・・・・ P.3
- Before first use of your teplo・・・・・・・ P.4
- Operating your teplo・・・・・・・ P.8
- Children・・・・・・・ P.11
- Additional Features・・・・・・・ P.11
- Care and Cleaning・・・・・・・ P.12
- Additional Warnings・・・・・・・ P.13
- Damage/Repair・・・・・・・ P.13
- Storage・・・・・・・ P.14
- Customers Service・・・・・・・ P.14
- Regulatory Notices・・・・・・・ P.14
- Warranty・・・・・・・ P.15

P.2
Know your teplo
Lid
Infuser Unit
Shaft
Tab
Bearing
Infuser Mesh
Weight Holder
Infuser Weight
Glass Pot
Handle
Spout
Glass Pot
Connector
Magnet
Magnet Holder
Maximum water
350ml
Mesh Holder

P.3
Display
The LED display located on the Power Base changes color to indicate status.
LED Display
Status
Yellow blinking
Stand by with no BLE connection with mobile app
Blue blinking
Ready to start pairing via BLE
White blinking
Stand by after BLE connection with mobile app
White
Waiting for the function button to be pressed, to start
brewing
Green blinking
Brewing
Green
Brewing complete
Red
Error
Power Button
LED
Sensors
Function Button
Base Connector
Base Arm
Power Connector
Power Base
Power Plug
Power Cord

P.4
Before first use of your teplo
Download teplo app from app store.
! iOS device download link: http://teplotea.com/iosapp
! Android device download link: http://teplotea.com/androidapp
Preparing teplo for use:
We have a guided experience on the app on how to use the teplo. Setup your
teplo with the app.
1. Remove and safely discard packing material, packing tape and labels.
2. Remove the Glass Pot, Lid, and the Infuser Unit. Wash the Lid, Infuser Unit
and the inside of the Glass Pot in warm soapy water with a soft sponge, rinse
and dry thoroughly.
WARNING: To protect against fire, electric shock and injury do not
immerse Power Cord, Plug, Power Base, or the base of the Glass Pot in
water.
How to lock and unlock the Lid:
・Open
Slide the knob and rotate the Lid to
counterclockwise to unlock the Lid.
Lift the Lid to open.
WARNING: Do not use water to
clean the base of the Glass Pot.
Close the Lid and rotate the Lid to
clockwise to lock the Lid.
・ Close

P.5
How to attach and detach the infuser units:
・Attach
・Detach
Push the magnet part of the
infuser and remove from the
hook.
Hold the plastic part of the infuser
mesh and rotate the infuser mesh to
clockwise to open the infuser.
Hold the plastic part of the infuser mesh
and rotate the infuser mesh to clockwise.
Make sure the infuser mesh is attached
and locked to the infuser weight.
Insert the shaft of the infuser to the
bearing and push the other side of the
infuser to the hook.

P.6
3. Place the Power Base on a flat, dry surface.
4. Unwind the Power Cord completely, insert the power cord into the Power
Base, and insert the Power Plug into a grounded wall outlet. Always unwind
Power Cord fully before use.
NOTE: Remove and safely discard the protective cover on the Power Plug.
NOTE: Always attach plug to the Power Base first, then plug Power Cord
into the wall outlet. To disconnect, turn power off, then remove plug from
wall outlet.
WARNING: The power cord is equipped with a three prong grounding
plug. To reduce the risk of electrical shock teplo must be grounded using
a properly grounded 3-hole outlet.
5. After the base LED is turned off, single press the power button.
6. Pair teplo with the teplo app by opening the teplo app and following the
instruction on the mobile app for paring setup.
7. Clean your teplo without tea by combining the Infuser weight and the infuser
mesh, and securely attaching the Infuser to the Lid.

P.7
8. Fill the Glass Pot to maximum water line (350mL WATER MAX) and place on
the Power Base. Securely fit the Lid onto the Glass Pot.
WARNING: Over-filling the Glass Pot above the '350' line may result in
injuries and/or damage to teplo as a result of overflowing hot or boiling
water. Filling below the '150' line will result in teplo switching off before
the water has boiled or reached the selected temperature.
9. Follow the instruction on the mobile app to complete the test operation.
10. Discard the water after completing the test operation.
WARNING: Never touch the Infuser weight, Infuser mesh or the Glass
Pot until they are cooled after brewing. Touching these items before
cooling can cause serious burns or injuries.
11. Rinse the Glass Pot and Infuser and dry thoroughly.
12. teplo is now ready to use. Use the mobile app to enjoy your first brew.

P.8
Operating your teplo
1. Remove the Glass Pot from the Power Base, then remove Lid. When brewing
tea, fill with desired amount of water. Make sure to fill the Glass Pot with water
between ʻ150ʼ line and ʻ350ʼ line. If the Glass Pot is hot, allow to cool before
filling with water.
NOTE: Do not operate teplo without water. Doing so may cause breakage
of the glassware.
WARNING: Over-filling the Glass Pot above the '350' line may result in
injuries and/or damage to teplo as a result of overflowing hot or boiling
water.
2. Place the Infuser on a flat, dry surface. Put desired amount of tea leaves into
the Infuser weight and attach the Infuser mesh. *If using teplo teas, put all the
tea leaves in the packet. Teplo tea packets contain the exact amount of teas for
a single brew. For best experience use teplo teas.

P.9
3. Attach the Infuser to the Lid.
4. Attach the Lid securely to the Glass Pot and place the Glass Pot on the Power
base.
NOTE: Do not place objects on top of the Lid.
WARNING: Do not open the Lid during operation as scalding may
occur.
NOTE: When in operation, keep teplo a minimum of 8 inches (20cm) from
walls and other objects.
WARNING: - The Glass Pot must be used only with the Power Base
supplied. Do not use the Glass Pot on a stove or range top.

P.10
5. Press the Power button on the Power Base and open the mobile app.
6. Follow the instruction on the mobile app to brew your tea.
7. teplo automatically adjusts the water temperature and the Infuser will
automatically rotate to start and stop brewing.
8. The Infuser will stop rotating when teplo completes brewing.
NOTE: Use caution when removing the Glass Pot containing hot liquid
from the Power Base.
WARNING: Do not remove the Glass Pot from the Power Base during
heating or when the basket is in operation. Ensure that the tea brewing
cycle is complete before removing the Glass Pot from the Power Base.

P.11
9. Pour tea into cup and enjoy.
WARNING: Never touch the Infuser Weight, Infuser Mesh, or the Glass
Pot until they are cooled after brewing. Touching these items before
cooling can cause serious burns or injuries.
10. Hold the Power button for 3 seconds to turn power off. The main power will
turn off automatically if there is no interactions with teplo for 30 minutes.
11. Disconnect the Power Cord from the wall outlet when teplo is unattended or
not in use. To disconnect from the wall outlet, turn teplo OFF, then remove the
Power Plug from the wall outlet.
Children
! Closely supervise children when operating electrical appliances.
! During operation teplo creates hot water which can cause severe burns.
WARNING: Do not place teplo near the edge of a table or countertop
where it could be reached by children during operation.
WARNING: Do not allow the Power Cord hang over the edge of a table
or countertop where children can reach it and pull teplo off the counter or
table causing injury.
Additional Features
1. After you brew once, you can use the function button for repeat brews.
! To repeat the same brewing conditions as the most recent brew, long
press the function button for 3 seconds when the LED is on standby (with
or without BLE connection with the app).
! To change the brewing condition or enjoy a personalized brew, use the
mobile app.
2. Use the “keep warm” feature on the mobile app to keep tea warm after
brewing is completed.

P.12
Care and Cleaning
1. Ensure teplo is turned OFF by pressing and holding the Power Button for 3
seconds. teplo is off when the Base LED is off.
2. Remove the Power Plug from the wall outlet. Allow all parts of teplo to cool
completely before disassembling and cleaning.
3. Wash the Lid, Infuser mesh and Infuser weight in warm soapy water with a
soft sponge, rinse and dry thoroughly.
NOTE: The Lid, Infuser weight, and Infuser Mesh are dishwasher safe.
4. Empty the Glass Pot after each use. Do not allow brewed tea to stand
overnight.
5. Wipe the interior of the Glass Pot with a soft damp sponge or rinse with warm
water.
WARNING: Do not immerse or wash the base of the Glass Pot under
running water.
6. Wipe the exterior of the Glass pot with a soft damp cloth to clean.
NOTE: Do not use chemicals, steel wool, or abrasive cleaners to clean the
inside or outside of the Glass pot as these may scratch the surface.
7. Wipe the Power Base with a soft damp sponge. Let all surfaces dry thoroughly
prior to inserting the Power Plug into a wall outlet.

P.13
Additional Warnings
! Do not touch hot surfaces. Use handles or knobs.
! Do not allow the Power Cord to come into contact with hot surfaces.
! Do not place teplo on or near heated surfaces.
! Do not use teplo for anything other than its intended purpose.
! teplo is intended to heat water for tea. teplo should not be used to heat or boil
any other liquids or foodstuffs.
! Not for use in moving vehicles or boats.
WARNING: teplo contains electromagnets. Magnets may pose a
danger to persons possessing electronic medical equipment such as
pacemakers and defibrillators. Magnets may impair normal operations of
certain electronic medical equipment possibly leading to injury or death.
! Keep magnets away from magnetic recording media such as magnetic disks
and tapes, and credit cards.
! The use of accessory attachments not recommended may result in fire, electric
shock or injury to persons.
Damage/Repair
1. Regularly inspect teplo, including the Power Cord and Plug, for damage.
2. Do not operate teplo if the appliance has been damaged or has malfunctioned.
WARNING: Use of teplo when damaged could lead to fire or injury.
3. If teplo has been damaged, return it to an authorized service facility for
examination and repair. Do not use teplo if the Glass Pot is cracked or chipped.
4. For maintenance or repair questions email: [e-mail]
NOTE: For additional safety teplo is fitted with a thermal cut out. In the
event of severe overheating, teplo will automatically shut down to prevent
further damage. Should this occur, email teplo service:
[e-mail]

P.14
Storage
1. Ensure the teplo is switched off, cleaned and dried before storing.
2. Ensure that the assembled infuser is securely attached to the Lid.
3. Ensure that the Lid is securely in place.
4. Stand teplo upright on the Power Base. Do not store anything on top of your
teplo.
Customers Service
• For troubleshooting suggestions or to contact Customer Support, please visit
teplotea.com/care-usa, or email US Customer Service at:
care[email protected]
Regulatory Notices
USA: Federal Communications Commission (FCC) statement
Teplo MODEL: T002
Contact: LOAD&ROAD, INC.
Address: 231 Forest Street, Blank Center, Babson Park, MA 02481, U.S.A.
Email: [email protected]
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC CAUTION Changes or modifications not expressly approved by the party
responsible for compliance could void the userʼs authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

P.15
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines as this equipment has very low levels of RF energy.
Warranty
LOAD&ROAD warrants teplo against defects that are due to faulty material or
workmanship for a period of one (1) year from the date of original consumer
purchase. This warranty does not cover damage from abuse, neglect, use for
commercial purposes, or any other use not found in the “Instructions for Use.”
The warranty does not apply to damage to glass parts. If the appliance should
become defective within the warranty period, please contact US Customer
Service at: [e-mail].
LOAD&ROAD expressly disclaims all responsibility for special or consequential
damages or incidental losses. All warranty of merchantability or fitness with
respect to teplo is limited to the one year limited warranty period.