Teral PL Series User manual

Teral Inc.
Instruction Manual
Submersible Sewage Pump
Model: PL / SSU / PV / SVC / BO /
KO / SCU
Warning
Do not carry out operation, inspection or maintenance of the pump until you read this manual and
understand the content.
Keep this manual carefully at hand so that it can be consulted at anytime when operating, inspecting or
maintaining the pump.
For contractors who carry out equipment work:
Please be sure to deliver this manual to the customer who will operate, inspect or maintain the pump.

I
Limited warranties
1. In the event of a failure or breakage under proper use of the product during the warranty period,
equipment supplied by Teral Inc. shall be repaired or replaced free of charge within the scope of the
relevant part, provided that such failure or breakage is attributable to inadequacy of the design or
workmanship of the equipment.
2. The warranty mentioned in the above clause shall be only the mechanical warranty of the defective
part, and shall not cover any expenses or other damage arising from the failure or breakage.
3. In the event of the following failures and breakage, the costs of the repairs shall be borne by the user.
(1) Failures and breakage attributable to equipment that was not delivered by Teral Inc.
(2) Failures and breakage after the expiration of the warranty period
(3) Failures and breakage caused by disasters or force majeure, such as fire, acts of God or
earthquakes
(4) Failures and breakage resulting from repairs or modifications made without the consent of Teral
Inc.
(5) Failures and breakage when parts other than those designated by Teral Inc. are used
4. Teral Inc. shall not be liable for any damage caused by incorrect or reckless use of the pump. Cost
and expenses incurred for sending engineer(s) in such a case shall be borne by the user.
5. If the cause of the failure is unclear, necessary actions shall be determined through mutual
consultation.

II
Purpose of this manual
The purpose of this manual is to provide the user with detailed information necessary to operate,
maintain and inspect the pump properly.
This manual contains the following information and is intended for persons experienced in the operation
of pumps, or for those who have been trained by such experienced operators. Only qualified personnel
such as licensed electrical engineers are allowed to carry out the electrical wiring work.
Contents
Page
Limited warranties············································································································································ I
Purpose of this manual··································································································································· II
Contents ··························································································································································· II
1. Safety precautions ···································································································································1-1
1.1 Safety indications and their meanings······························································································1-1
1.2 Safety precautions····························································································································1-1
1.2.1. Precautions for operation··········································································································1-1
1.2.2. Precautions for installation, maintenance, and inspection························································1-1
2. Configuration and overview of the pump ·································································································2-1
2.1 Part names ·······································································································································2-1
2.2 Pump specifications··························································································································2-2
3. Installation ················································································································································3-1
3.1 Before using the pump ·····················································································································3-1
3.2 Precautions for installation ···············································································································3-1
3.3 Precautions for piping work ··············································································································3-2
3.4 Precautions for wiring work ··············································································································3-2
4. Preparation for operation ·························································································································4-1
4.1 Check items before test operation····································································································4-1
4.1.1. Check items related to the electrical system ············································································4-1
4.1.2. Check items related to the operating water level······································································4-1
4.2 Test operation···································································································································4-3
4.3 Check items related to automatic operation ·····················································································4-3
4.3.1. Automatic alternate operation···································································································4-3
4.3.2. Automatic alternate/parallel operation ······················································································4-3
5. Maintenance and inspection ····················································································································5-1
5.1 Precautions for maintenance and inspection ···················································································5-1
5.2 Maintenance check list ·····················································································································5-1
6. Troubleshooting ·······································································································································6-1
7. Detachable device (option) ······················································································································7-1
7.1 Names of components······················································································································7-1
7.1.1. C-type detachable device ·········································································································7-1
7.1.2. SEC type detachable device·····································································································7-1
7.2 Installation of the detachable device ································································································7-2
7.2.1. C-type detachable device ·········································································································7-2
7.2.2. SEC type detachable device·····································································································7-2
7.3 Installation of the pump ····················································································································7-3

1-1
1. Safety precautions
1.1 Safety indications and their meanings
This instruction manual divides precautions into the following four categories according to the level of
hazards (or the severity of the accident).
Be sure to understand the meanings of the following terms and comply with the content (instructions)
of the instruction manual.
Warning Term Meaning
Danger
Indicates an imminently hazardous situation. Failure to observe the
procedures or instructions will result in death or serious injury.
Warning
Indicates a potentially hazardous situation. Failure to observe the procedures
or instructions may result in death or serious injury.
Caution
Indicates a potentially hazardous situation. Failure to observe the procedures
or instructions will result in minor or moderate injury or cause damage to
equipment or devices.
Note Indicates information that is in particular to be noted or emphasized.
1.2 Safety precautions
1.2.1. Precautions for operation
(1) Ensure to apply the rated voltage to the pump.
(2) Check that the rotation direction is correct.
(3) Do not allow air to be sucked into the pump during the operation.
(4) Never perform zero-discharge operation for a long time.
Otherwise, it may cause the motor to burn out and/or lead to an electric shock.
1.2.2. Precautions for installation, maintenance, and inspection
(1) Installation, maintenance, and inspection must only be carried out by personnel who have been
trained to handle the pump.
Only qualified personnel such as licensed electrical engineers are allowed to carry out electric
wiring work.
(2) Before carrying out maintenance or inspection, be sure to stop the pump and turn off the power
supply.
If you carry out such work with the power turned on, you may suffer an electric shock
(3) If you need to modify or repair the pump, be sure to ask the manufacturer or the vendor.
(4) If you find anything wrong with the pump, stop the operation immediately and turn off the power,
and then contact the vendor from which you purchased the product or the service center
specified by the manufacturer.
If you continue to operate the pump without fixing the problem, it may lead to an electric shock
and/or a fire.
(5) Do not lift or lower the pump using the cabtyre cable.
Otherwise, it may damage the cable and lead to an electric shock.
(6) Do not run the pump if the insulation resistance is not higher than 1MΩ.

2-1
2. Configuration and overview of the pump
2.1 Part names
[Models PLA, PLT, SSUA, and SSUT]
(The float switch is not fitted to the models PL and SSU.)
Float switch
Float switch holder
Float mounting bar
Casing
Motor
Cabtyre cable
Strainer
(The models PLA and PLT have a strainer
of a different shape.)
Air vent hole
[Models PVA, PVT, BOA, BOT, KOA, KOT, SVCA, SVCT, SCUA, and SCUT]
(The float switch is not fitted to the models PV, BO, KO, SVC, and SCU.)
Float switch
Float switch holder
Float mounting bar
Casing
Motor
Cabtyre cable
Air vent hole

2-2
2.2 Pump specifications
If you have purchased our standard product, refer to the “Standard specifications” table. If you have
also purchased a custom-made product with special specifications, refer to the specifications including
the external dimensions drawing.
Caution
Do not use this pump under any conditions other than those provided in
the specifications. Otherwise, it may lead to an electric shock, a fire, or
failures.
Standard specifications
Model PL SSU PV SVC
Liquid quality Dirty water Dirty water, contaminant, waste water
Liquid temperature 0 to 40°C
PH 6 to 8 5 to 9 6 to 8 5 to 9
Pump
Size of solids
that can pass
Diameter: 5 mm or less
Length: 100% or less of
the pump bore
Diameter: 10% or less
of the pump bore
Length: 100% or less of
the pump bore
Diameter: 20 mm or less
Diameter: 60 to 70% of
the pump bore
Length: 400% or less of
the pump bore
Output (kW) 0.15 to 0.75 1.5 to 7.5 0.15 to 0.75 1.5 to 7.5
Number of
poles 2 poles
Phase/Voltage
Single-phase 100 V
(0.15 to 0.4 kW)
Three-phase 200/220 V
Three-phase 200/220 V
Single-phase 100V
(0.15 to 0.4 kW)
Three-phase 200/220 V
Three-phase 200/220 V
Type Dry type submersible motor
Motor
Protective
device Built-in protector, automatic reset type
Lubricating oil VG10 VG32 VG10 VG32
Model BO KO SCU
Liquid quality Dirty water, contaminant, waste water
Liquid temperature 0 to 40°C
PH 5 to 9
Pump
Size of solids
that can pass
Diameter: 40–70% or
less of the pump bore
Length: 300% or less of
the pump bore
Diameter: 50–70% or
less of the pump bore
Length: 300% or less of
the pump bore
Diameter: 100% or less
of the pump bore
Length: 500% or less of
the pump bore
Output (kW) 0.75 to 22 0.75 to 7.5 0.75 to 22
Number of
poles 4 poles
Phase/Voltage Three-phase 200/220 V
Type Dry type submersible motor
Motor
Protective
device
Built-in protector
Automatic reset type
(7.5 kW or less)
Built-in protector
Automatic reset type
Built-in protector
Automatic reset type
(7.5 kW or less)
Lubricating oil VG32

3-1
3. Installation
3.1 Before using the pump
When you receive the pump, check the following points first.
If there are any problems, contact the vendor from which you purchased the product.
Caution
Make sure that the delivered package is placed right-side up before
unpacking. Pay special attention to nails especially when opening a
wooden crate or you may get injured.
(1) Check the nameplate to verify that the delivered product is exactly what you ordered.
(2) Check that no part of the product is damaged during transportation.
(3) Check all the fastening parts including bolts and nuts are securely tightened.
(4) Check all the accessories that you ordered have been delivered.
3.2 Precautions for installation
(1) For an automatic type model, be sure to keep the float switch away from the direct inflow of water.
Otherwise, automatic operation does not work properly, which could cause air to be sucked in
and/or lead to dry run.
(2) The suction port of the pump must be kept at a distance of at least five times the inflow pipe bore
from the inflow of water so that the flow does not get close to the port.
[Good example] [Bad example]

3-2
Warning
• Do not lift or lower the pump using the cabtyre cable.
Otherwise, it may damage the cable and lead to an electric shock.
• Before lifting the pump, refer to the catalog, the external dimensions
drawing, and other documents to check the weight of the pump. Do
not lift the unit if the weight exceeds the rated load of the lifting
equipment/device to be used.
(3) Do not install the pump directly on soft or muddy ground for operation.
Otherwise, the pump may sink, which may cause the pump and piping system to be clogged with
mud, sand, and other foreign matter, and ultimately disabling the operation.
3.3 Precautions for piping work
(1) The drain pipe should be corresponding to or larger diameter than the discharge port size, and
lay the piping to achieve minimal piping resistance.
(2) If the discharge port of piping is submerged in water, back flow may occur from the siphon effect
when the pump stops.
Keep the discharge port above the water level or attach a check valve.
(3) If you need to discharge water from the above-ground piping when the pump is not running, it is
useful to attach a check valve with a bypass function.
(4) When the piping work is complete, clean the inside of the reservoir/water tank.
Warning
Before starting the cleaning work, be sure to stop the pump and turn off
the power supply.
If you carry out such work with the power turned on, you may get an
electric shock.
3.4 Precautions for wiring work
Warning
• Carry out wiring work according to the technical standards for
electrical facilities, as well as the indoor wiring regulations.
Incorrect wiring may lead to an electric leak or a fire.
• Ensure to connect a ground wire. Do not connect the ground wire of
the pump to the ground wire of a gas pipe, water pipe, lightening rod,
or telephone line.
Incomplete grounding work may lead to an electric shock.
• A ground fault interrupter may be required depending on the place
where the pump is installed.
If a ground fault interrupter is not installed in such a place, it may lead
to an electric shock.

3-3
(1) When connecting the connection terminals of the cabtyre cable to a power supply, be sure to
check the rotation direction.
To reverse the rotation direction, swap two of the three wires.
(2) Reverse rotation from incorrect wiring may generate abnormal noise and decrease the pump
discharge rate, thus leading to failures.
When the motor is rotating in the normal direction, the pressure gauge indicates a higher value
and the pump discharge rate is higher (than during the reverse rotation).
Slightly open the valve on the pump discharge side, and run the pump to check the direction.
[Motor protection device]
The motor has a built-in protector in order to prevent burnout if the motor temperature becomes
abnormally high because of an overload, lockup, or open phase.
1) 7.5 kW or less output
For motors with 7.5 kW or less output, a protector is incorporated into the winding circuit. In the
event of an abnormal temperature rise at the winding circuit, the protector breaks the winding
circuit to disconnect the power supply. When the temperature drops to the normal level after the
power break, the protector resets automatically. Therefore, the motor is protected independently
of the control panel above the ground.
2) 11 kW or higher output
For motors with 11 kW or higher output, a protector is incorporated into a circuit other than the
winding circuit. In the event of an abnormal temperature rise at the winding circuit, the protector
breaks the circuit which has the built-in protector (Circuit P1-P2). When the temperature drops to
the normal level, the protector resets automatically.
For protection of these motors, the continuity of the Circuit P1-P2 needs to be detected on the
control panel above the ground to control the power supply of the pump.
The control panel enables the power supply during the continuity of the Circuit P1-P2, and
disconnects the power supply on detection of power break of the Circuit to protect the motor
winding against an abnormal temperature rise. In this way, the motor can be protected by the
control panel above the ground.
Single phase (0.15, 0.25 kW)
Protector
Sub Main
Sub
Main
Single phase (0.4 kW)
Protector
(Red)
(Red)
(White)
(White)
(Red)
(White)
(Black)
Protector
Motor winding
Motor winding
Motor winding
Three phases
(Red)
(White)
(Black)(Red)
(Black)
(White)

4-1
4. Preparation for operation
4.1 Check items before test operation
4.1.1. Check items related to the electrical system
(1) Check that the pump is correctly wired.
(2) Check that the terminals are securely connected.
(3) Check that the pump is securely grounded.
(4) Check that the setup value of the overload protection device is consistent with the rated current
value of the pump.
Warning
Do not use the pump at any voltage other than the rated voltage.
Otherwise, it may lead to a fire or an electric shock.
4.1.2. Check items related to the operating water level
(1) For non-automatic type (Models PL, SSU, PV, BO, KO, SVC, and SCU)
 You can adjust the operating water level through the control panel and the float switches.
Warning
Do not allow air to be sucked into the pump during the operation.
Otherwise, it may cause the motor to burn out and/or lead to an electric
shock.
 When you continuously run the pump for over 30 minutes, ensure that the stop level is above
the water level B (near the connection flange between the motor frame and the upper bracket)
during the operation.
(2) For automatic type (Models PLA, SSUA, PVA, BOA, KOA, SVCA, and SCUA)
 By simply turning on the power, you can start the automatic operation through the float switch
and the automatic operation device (built in the pump).
 The stop level is the minimum water level up to which the pump can still run when the water
level drops during the operation. At the stop level, the float switch trips to stop the pump
automatically.
 Set the stopping float to a water level at which the float switch trips to turn off and where the
[Non-automatic type] [
A
utomatic type]
Start level
Stop level when the pump
runs for over 30 minutes.
Stop level
Stop level
(Adjustable)
B

4-2
casing is completely submerged in water.
Warning
Do not allow air to be sucked into the pump during the operation.
Otherwise, it may cause the motor to burn out and/or lead to an electric
shock.
 You can adjust the start level by moving up or down the float switch holder.
If the supplied float mounting bar is too short, replace it with a longer vinyl chloride pipe (13A,
OD: φ18 for water service).
Note
Be aware that if the start level is too close to the stop level, the pump
frequently starts up and stops, which may cause failures.
Keep a distance of at least 50 mm between them.
(3) Automatic alternate/parallel type (PLT, SSUT, PVT, BOT, KOT, SVCT, and SCUT)
 By simply turning on the power, you can start the automatic alternate/parallel operation through
the float switch and the automatic alternate/parallel operation device (built in the pump).
 Set the stop level to a level equal to or higher than the minimum water level up to which the
pump can still run when the water level drops during the operation. At the stop level, the float
switch trips to stop the pump automatically.
 Set the stopping float to a water level at which the float switch trips to turn off and where the
casing is completely submerged in water.
 Set the float switches so that their positions are arranged in the ascending order of:
F1<F2<F3<F4<F5 (see Figure 1). Ensure to keep a distance of at least 50 mm between the
floats. A wrong setting of the water levels may cause a malfunction.
Figure 1
 If you wish to set the float switch to a water level higher than that is reachable by the supplied
float mounting bar, replace the bar with a longer vinyl chloride pipe (13A, OD: φ18 for water
service), insert it into the holder attached to the float, and fix it in place.
Note
Note that the models PLA, PLT, PVA, and PVT use floats of a different
color.
(Black) (Black)
(Yellow) (Orange)
(Orange) (Yellow)
(Yellow) (Orange)
(Orange) (Yellow)

4-3
4.2 Test operation
Warning
If there is a person in a place where water is stored, such as a bath, a
pool, or a pond, never run any submerged pumps.
Otherwise, it may lead to an electric shock.
(1) Referring to “3.4. Precautions for wiring work,” be sure to check the rotation direction of the motor
after installing the pump in water.
Caution
Check that the rotation direction is correct.
The wrong direction may cause a fire.
(2) Turn on the power to start the pump.
Warning
Never perform zero-discharge operation for a long time.
Otherwise, it may cause the motor to burn out and/or lead to an electric
shock.
(3) Gradually open the valve on the discharge side to adjust the pressure to the specified level.
(4) Check for any abnormal pressure, current, vibration, noise, or other abnormal conditions.
(5) Close the valve on the discharge side, and stop the pump.
4.3 Check items related to automatic operation
(See Figure 2.)
4.3.1. Automatic alternate operation
Each time the water level B is reached, the system starts and stops the pump #1 and the pump #2
alternately.
4.3.2. Automatic alternate/parallel operation
(1) If an abnormal increase in water raises the water level even though the pump #2 is running, the
pump #1 also starts up at the water level A, and the two pumps run at the same time to lower the
water level.
(2) If an abnormal increase in water raises the water level even though the pump #1 is running, the
pump #2 also starts up at the water level D, and the two pumps run at the same time to lower the
water level.
(3) If the pump #2 fails, the system repeats the cycle of starting the pump #1 alternately at the water
level B and at the water level A and stopping the pump at the water level C.
(4) If the pump #1 fails, the system repeats the cycle of starting the pump #2 at the water level D and
stopping the pump at the water level E.

4-4
Figure 2
Normal operation Abnormal condition
Automatic alternate
operation Abnormal increase in water Pump failure
Pump #2 fails Pump #1 fails Abnormal condition
starts Pump #1
Pump #2 starts
Pum
p
#1 starts
Pump #1 stops
Pump #2 stops
Water level A (start level for abnormal condition)
Water level B
(Start level)
Water level C
(Stop level)
Pump #1
Master (T type)
Pump #2
Slave (A type)
Water level D (Start level)
Water level E (Stop level)
#1
#2
Pump #2 Pump #2
Pump #2
Pump #1

5-1
5. Maintenance and inspection
5.1 Precautions for maintenance and inspection
When carrying out a daily inspection, carefully observe the following points.
(1) Because a submersible motor is used, periodically check the insulation resistance. If the
insulation has degraded rapidly, inspect the motor.
Warning
Do not run the pump if the insulation resistance is not higher than 1MΩ.
Otherwise, it may lead to an electric shock and/or a fire.
Warning
Do not expose the submersible motor or the cabtyre cable to direct
sunlight for a long time.
Otherwise, it may damage the cable and lead to an electric shock and/or
a fire.
(2) Ensure to use a hanging bolt for transportation.
Warning
Do not lift or lower the pump using the cabtyre cable.
Otherwise, it may damage the cable and lead to an electric shock.
(3) Check for any abnormal vibration, noise, overcurrent, or other abnormal conditions during the
operation.
For also monitoring the operating conditions, it is recommended to use a dedicated control panel.
Note
Motors with 7.5 kW or less output have a built-in protector as standard in
order to prevent burnout if the motor temperature becomes abnormally
high because of an overload, lockup, or open phase.
(4) Depending on the installation environment, the sliding parts may rust and foreign matter may
accumulate. If you do not use the pump for a long time, periodically run the pump (once a week
as a guide) to prevent rusting at the sliding parts and accumulation of foreign matter. If you store
a submerged pump on the ground, completely drain water from the inside of the pump, clean and
dry it, and then store it at a dry place.

6-1
5.2 Maintenance check list
Frequency Consumables
Inspection
point Inspection item Method Criterion
Daily
Monthly
Half-yearly
Yearly
Part name Qty. Replacement
cycle
Voltage Measure
The specified voltage is
applied.

Voltage fluctuation Measure Within the allowable
fluctuation range

Power
Power terminal
block inside the
panel
Loose screws Tighten Firmly tightened 
Clogging Disassemble
and inspect No clogging 
Impellers
Wear Disassemble
and inspect No abnormal condition 
Main shaft and
its surrounding
area
Smooth rotation Rotate by
hand Not unusually stiff 
Bearings Smooth rotation
Rotate by
hand Not unusually stiff Bearing 2 3 years
Casing Clogging of the air
vent hole Visual check No clogging 
Oil - 0.5 years
Mechanical
seals Water leakage Oil condition No milky oil and no mixture of water Mechanical
seal 1 1 year
Appearance Unusual noise,
vibration Listen No abnormal condition 
Pumps and motors
Insulation
resistance
Between the
ground and each
lead
Megger At least 1 MΩ
6. Troubleshooting
Problem Cause Measures
The power fuse is blown. · Replace it with an appropriate fuse.
Poor connection or contact of power
wires
· Check the power voltage.
· When replacement is required, ask the vendor.
Poor connection and disconnection of
wiring
· Check the wires with a tester etc., and replace
defective wires with non-defective wires.
The power voltage is too low. · Check the power voltage.
If it is too low, contact the power company.
Mud or solid matter is caught in the
impeller (overload).
· Ask the vendor for investigation because
disassembly and inspection are required.
Float switch failure · Ask the vendor because it is necessary to
inspect and replace the float switch.
The pump does not start.
The water level is lower than the start
level.
· Store water until it reaches the start level or
change the setting position of the float switch.
Voltage drop · Check the power voltage.
· If it is too low, contact the power company.
Clogging of the strainer · Clean the strainer.
Wear of the impeller · Because it is necessary to replace the impeller,
contact Teral Inc. or the service company.
Defective or improper piping
Lower performance
Sucking of air
· Repair or correct the piping appropriately.
· Correctly set the stop level.
The pump starts up but does
not discharge (pump) water. There is air trapped inside the casing. · Clean the air vent hole of the casing.

7-1
7. Detachable device (option)
7.1 Names of components
7.1.1. C-type detachable device
Discharge pipe
Sliding guide
Companion flange
Pipe supporter
Anchor bolt
Balance chain
Hanging chain
Guide pipe
Note
The guide pipe is not a standard accessory.
If the customer provides this on its own, refer
to the catalog, the external dimensions
drawing, and other documents to check the
size.
５
３
１
２
８
４
６
７
7.1.2. SEC type detachable device
Support base
Discharge elbow
Companion flange
Sliding guide
Taper flange
Pipe supporter
Guide pin
(* Other than the model SEC-1B
detachable device)
Anchor bolt
Balance chain
Hanging chain
{
11 Guide pipe
Note
The guide pipe is not a standard accessory.
If the customer provides this on its own, refer
to the catalog, the external dimensions
drawing, and other documents to check the
size.
１１
６
４
３
２
１
８
１０
５
９
７

7-2
7.2 Installation of the detachable device
Caution
Ensure to install the detachable device so that it can lift and lower the
pump properly.
If the guide pipe is not installed precisely vertically, the detachable
device may not be able to fully lift or lower the pump.
7.2.1. C-type detachable device
(1) On completion of the foundation work, determine
the positions of the parts so that the flange face of
the discharge pipe and the guide pipe are both
vertical. Then fix the gear in place with the anchor
bolts.
(2) Cut off the guide pipe to the required length in
advance, and cut taper-pipe threads on one end.
(3) Screw the guide pipe into the discharge pipe.
(4) Insert the pipe supporter into the upper end of the
guide pipe, and fix it to a manhole wall.
If the pipe supporter is not fixed to a wall, connect
the supporter with a chain or the like to prevent it
from falling.
(5) Install a drain pipe.
7.2.2. SEC type detachable device
(1) On completion of the foundation work, determine
the positions of the parts so that the flange face of
the discharge elbow is horizontal and the guide pipe
is vertical. Then fix the gear in place with the anchor
bolts.
(2) Cut off the guide pipe to the required length in
advance. For SEC-1B, cut taper-pipe threads on
one end.
(3) Insert the guide pipe into the projected area of the
support base.
(4) Insert the guide pin or the pipe supporter into the
upper end of the guide pipe, and fix the pipe
supporter to a manhole wall.
(5) Install a drain pipe.
Insert the guide pin.
Erect the guide
pipe vertically.
Insert or screw the
guide pipe into the
base.
Insert the pipe supporter.
Connect it with a
chain or the like.
Erect the guide
pipe vertically.
Screw the guide pipe
into the drain pipe.

7-3
7.3 Installation of the pump
(1) Adjust the hanging position of the balance chain so that the hoisted pump is not tilted.
(2) Hold the hanging chain with a chain block or other tools, and slowly lower the sliding guide along
the guide pipe.
(3) Put the hanging chain on a hook of the manhole so that it does not fall in the tank.
(4) Ensure that the cabtyre cable is long enough to lift and lower the pump in the tank.
Caution
If the cabtyre cable is too long, it may be sucked into the pump, thus
leading to damage and an electric leak.
(5) When lifting the pump, hold the hanging chain with a chain block or other tools, and slowly lift it
along the guide pipe.
Caution
• If there is a drag force or catch during lifting because of adherence of
foreign matter or other factors, do not lift the pump forcibly. Instead,
slightly change the hanging position, and then lift it again.
• Never pull the cabtyre cable.
Otherwise, it may lead to an electric leak.

Head Office
230, Moriwake, Miyuki-cho, Fukuyama-city, Hiroshima, 720-0003, Japan
Tel.[phone] Fax.[phone]
www.teral.net
2016 10
E‑IMN‑00012‑000‑D