Tethon 3D Bison 1000 User manual
Welcome to your new Bison 1000 3D Printer!
Table of Contents
1
DLP Printing
What is DLP 3D Printing?
●DLP = Digital Light Processing
●3D Printing in this method uses a cross section image of the object to
be printed and cures this as a layer on the build plate using UV light.
●Due to the uniform projected light this is a faster method of printing
than SLA (Stereolithography) 3D printing.
2
Introduction to the
Bison 1000
The Bison 1000 DLP 3D printer is an ultra detailed 3D printer
suitable for complex industrial designs. It is compatible with
numerous resins as well as custom formulated in-house resins.
3
4
5
Precautions
6
7
Process
8
Printing
Loading File
Create a model file from your Tethonware software and save onto a USB
drive. Insert it into the USB slot on the front of your machine.
If you have recently printed a file it will be already loaded up on the main
screen and you can cycle through these by tapping the arrows on either side
of the print.
When selecting a new file from the USB, tap the arrow on the far right side
of the display and navigate to your file to select it.
9
Settings
Once you have your file loaded make sure you have the correct settings for
your material choice. To navigate to these settings tap the arrow on the far
left side of the display until you get to the settings screen in the image
below.
Select the correct material and make sure your micron thickness matches
the created sliced file.
Hit Save when finished.
10
Starting Print
Set resin tray in place and secure down by the two latches on the sides
Insert the build plate, handle facing forward, and tighten the knob on the
top.
If your settings are correct tap the image of the file you would like to print.
Select Print
Follow message on screen and tap screen one more time to begin the print.
Your printer has started! If using the heated tray your printer will heat until
the sensor reads the correct temperature and then begin printing.
11
Safety
●Isopropyl Alcohol (IPA) is a flammable substance. When not in
use keep in a closed container and out of the reach of children.
●Use caution when removing print from build plate. Metal scraper
can slip and cause a nasty ouchie.
●Always wear nitrile gloves and safety glasses when handling
resin. Wash resin off of skin with plenty of soap and water.
●Do not look directly into the projected UV light.
●When providing maintenance to the Bison 1000 always shut off
and unplug from the power source. Never access the interior of
the printer while it is still plugged in.
●Make sure to not overfill the resin tank as the build plate will
displace the resin further. Resin that spills over may damage the
printer.
12
Printer
Maintenance
It is important to keep the printer maintained to increase the longevity
of the Bison 1000. Use these following steps to clean and maintain
your printer.
●If resin drips or overflows from the tray onto the machine clean with
alcohol and paper towels. A microfiber towel is recommended to avoid
abrasion of the glass.
●Dust may accumulate over time on the lens of the light engine.
Remove with canned air or by using a microfiber cloth and wiping
gently in a circular motion.
Damage to the light engine lens can adversely affect the print quality. Handle with care.
●If not being used for an extended period of time, power down the
printer and store in a safe area.
13
Troubleshooting
●Print is not adhering to the build plate.
○Re-zero the build plate.
○Replace film in resin tray
●Light Engine is not turning on.
○Restart printer.
○Check brightness setting.
●Printed object is stretched or squashed
○Check to make sure the layer thickness is set to the
same thickness as the slice file. (would this be a resin
troubleshooting)
●Heater does not turn on
●Build plate is stuck at the top and printer will not boot up
14
Other manuals for Bison 1000
1
Table of contents
Other Tethon 3D 3D Printer manuals
