Teuco Hydroline T50 User manual

1/2 1
PRE-INSTALLATION CHART
Art. T50
Hydroline (h: mm 590)
67101076400 2015.02
R 6
620
1700
1768 ± 1
688 ± 1
44 ± 1
1766 ± 1
1766 ± 1
500
1730
1766 ± 1
430
680
480
85
85
min 200
1950
min 985
85
min 200
620
1700
1780
680
1760
700
507
1295
J
I
1/2"
Facing for sunken
installation
Facing for flush
installation
ELECTRICAL CHARACTERISTICS
V Hz
Power consumption
W
K074 (optional) 220 - 240 50/60 15
MY / MY-F 220 - 240 50/60 1000
HYDRAULIC CHARACTERISTICS
Water capacity (1)
lt
Emptying time (2)
min.
No. of Jets
Overflow water flow
rate
l/min.
310 9 32 -
8
Net Weight
kg
Floor Load
kg/m2
Delivery Weight
kg
Delivery dimensions
cm
68 450 101 191 x 82 x 83
N.B. Measurements must be taken once the floors and walls are finished. For the
correct operation of the product, we recommend installing it on surfaces where
floor level heating is not used.
BATHTUB INSTALLATION
It is advisable to position the bathtub, make the necessary connections and
check the water-tightness of the system before building the perimeter walls.
Before building the perimetre walls, it is advisable to position the bathtub and
make the necessary connections. It is mandatory to create a removable panel
on the side of the tank (l), as shown in the relevant picture, which allows both
system inspection and ventilation; the panel must be provided with openings,
of at least 0,05 sqm in total, to allow system ventilation. Build the perimeter
wall also on taps and control side and always provide an inspection panel (J)
to carry out system maintenance operations, as shown in the picture. When
making the panel, follow the dimensions indicated in the diagram. The panel must
be fastened securely in place (e.g. with screws) so that a tool must be used to
remove it, as provided for by current safety standards. Envisage a clearance of at
least 40 cm in front of the removable panels.
(1) At overflow level - (2) Measurement taken at Teuco siphon outlet, with the bathtub filled up to overflow level.
Measurements in mm
- Connection of water mixed for ½” water sheet spout
- Electrical connection
I, J - Inspection and ventilation panels

22/2
SR
260
332 332
395 ± 5
260
395 ± 5
44 ± 1
P
SR
P
28
52
18 max
30
45
70 max
112
52
R3.5
102,9
42,9
MY-F
P - Electric Control Panel
Flush installationSunken installation
SANITIZER
R - Filling up
DRAIN
S - Remote control
590
12 ± 1
10 ± 1
10 ± 1
578
12 ± 1
590
578
min 200
min 200
44 ± 1
Sunken installation
Flush installation
Data and specifications provided are not binding. Teuco Spa reserves the right to make any changes deemed appropriate without prior notice or obligation to update.
ELECTRICAL INSTALLATION
Make sure the appliance is connected to the power source by way of a residual
current device with minimum threshold =30 mA.
HYDRAULIC INSTALLATION
When the water from the mains is hard water (>200 mg/l), the installation of a water-
softener is advisable to ensure the efficient whirlpool operation.
BATHTUBS WITH COMBINED OVERFLOW AND FILLER SPOUT
A backflow prevention device must be installed, in compliance with the applicable
regulations in the country of destination.
Measurements in mm
Measurements in mm