Teuco 254 User manual

PRE-INSTALLATION CARD
2
2004.00
1/2 69
Measurements in mm.
500
1600
150
1280
350
100
350
150
270
750
150
750
500
150
1/2"
1/2"
100
350
80
750 150
500
1/2"
1/2"
1/2"
1/2"
500
1600
80
870
350
150
1/2"
1/2"
565
700
1700
565
700
1700
565
700
1700
565
700
1700
ART. 254
(mm 1700 x 700)
- Hot water connection for 1/2” tap fittings
- Cold water connection for 1/2” tap fittings
- IPX5 box with PG13.5 and PG9 cable clamps
- ELECTRICAL CONNECTION
- ALARM SYSTEM CONNECTION
N.B. Measurements must be taken once the floors and
walls are finished.
INSTALLATION OF THE BUILT-IN BATHTUB
Before building the perimetre walls, it is advisable to position
the bathtub and make the necessary connections. The recess
between the wall and the external edge of the bathtub must be
of a maximum of 1.5 cm. The service and ventilation panel is
obligatory and must be positioned as indicated in the
ASSEMBLY INSTRUCTIONS.
(1) - At overflow level
97
160
Siphon
with wall tap fittings with tap on rim of bathtub
with wall tap fittings with tap on rim of bathtub
Net
Weight
Kg.
48 160 267 73 1,1
Water
Content (1)
lt.
Floor
Load
Kg/m2
Delivery
Weight
Kg.
Delivery
Volume
m3
ART. 254
BATHTUB TURNED 180°
STANDARD BATHTUB
6
230 50
300 1WEX38 1210
Jets N. Water
Capacity l/m.
Air
Flow l/m.
HYDRAULIC CHARACTERISTICS
Whirlpool
Art.
VHz
Installed
Power
kW
ELECTRICAL CHARACTERISTICS
Hydromassage
EASY
8 400 2WTX38 1,35280 TOP
Art.

2
Data and specifications given are not binding. Teuco Guzzini Spa reserves the right to make changes deemed appropriate without prior notice or obligation to update.
70 2/2
740
50
740
50
100
100
100
100
1430270
1700
70
610
45
425
A-A
A
6565 570
A
565 485 6515
1530
480 620
700
350 350
70
ELECTRICAL INSTALLATION
• The electrical power supply system must be in compliance with national
statutory regulations.
• The appliance must be connected to the power supply by way of an isolating
switch (I) with minimum contact separation of 3 mm, sited away from areas 0,
1, 2 and 3 (IEC 364-7-701).
• Make certain the appliance is connected to the power source by way of a
residual current device with minimum threshold ≤30 mA.
• The electrical connection ( ) must include a connection to the earth
system and must be:
- permanent
- able to handle the rated current (see data plate).
- specified to liquids ingress protection category IPX5.
EQUIPOTENTIAL BONDING
The appliance must be equipotentially bonded by making the connection to the
terminal positioned at the
base of the electric motor/pump unit.
CONNECTION FOR ALARM SYSTEM
The product is prewired for connection to the bathroom alarm system (open/close
contact, voltage-free).
HYDRAULIC INSTALLATION
Prepare hot and cold water connections for water supply and the drain
connection.
When the water from the main is hard water, the installation of a water-softener is
advisable to ensure the efficient working of the hydromassage.
BATHTUBS WITH COMBINED OVERFLOW AND FILLER SPOUT
A DB type device must be installed at least 150 mm above the bathtub rim in
accordance with EN 1717 standard (see Taps art. 2009).
TOP
P- Electric Control Panel
D- Dispenser ( Ø 75 )
STANDARD BATHTUB
BATHTUB TURNED 180°
90
90
90
90
90
90
90
90 100
100
100
100
EASY
P- Electric Control Panel ( Ø 75 )
D- Dispenser ( Ø 75 )
A- Air Regulation ( Ø 60 )
STANDARD BATHTUB
BATHTUB TURNED 180°
ART. 254
P P
52
137
136
Ø75
40