Texas Instruments TRF3722 EVM User manual

32
35
33
42
LD BBQ_P
BBQ_N
RFOUT
VCC
VTUNE BBI_P NC
GND
PD RDBK
EXT_VCO BBI_N
1
2
3
8
10
44
45
46
47
48
39
40
41
43
37
38
23
36
34
30
29
28
27
26
25
DATA
CP_OUT
LO_OUTP
CLK
LO_OUTN
REFIN
LE
18
PFD
Charge
Pump
LO Div
6
SDM
24
13
12
6
22
21
16
14
20 19 17 15
9
4
11
7
5
GND
TX Div
Pre
Scaler
N Div
PLL Div
R Div
31
0O
90O
Serial Interface
VCC_TK
Product
Folder
Order
Now
Technical
Documents
Tools &
Software
Support &
Community
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TRF3722
SLWS245B –MAY 2014–REVISED FEBRUARY 2017
TRF3722 Quadrature Modulator with Integrated PLL and VCO
1
1 Features
1• IQ Modulator with Integrated PLL and VCO
• Integer-N/Fractional-N PLL
• Modulator Supports 400 MHz to 4200 MHz
• PLL and VCO Supports 280 MHz to 4100 MHz
• OIP3 at 900 MHz = 31 dBm
• OIP3 at 1800 MHz = 30 dBm
• VCO 1800-MHz Open Loop Phase Noise =
–141 dBc/Hz at 1 MHz Offset
• Independent LO Output Supports divide-by 1/2/4/8
• Modulator Low Power and High Gain Modes
• Multiple Power Down Modes
2 Applications
• Wireless Infrastructure
– CDMA: IS95, UMTS, CDMA2000, TD-SCDMA
– LTE, TD-LTE, LTE Advanced
– TDMA: GSM, EDGE, MC-GSM
• Point-to-Point Microwave, Point-to-Multipoint
Microwave
• Software Defined Radios
• RF Repeaters, Distributed Antenna Systems
3 Description
The TRF3722 is a high performance direct
conversion quadrature modulator with exceptional
linearity and low noise performance. The typical
0.25-V baseband common mode voltage supports
seamless interface with current source DACs. The
device integrates the PLL and VCO to provide the
local oscillator (LO) to the modulator. The PLL and
VCO provides excellent phase noise performance to
satisfy the most stringent transmit communication
requirements. The device also provides additional LO
output for driving a second modulator or down
converting mixer. The modulator features a high gain
mode for a typical 3-dB gain increase and a low
power mode when power optimization is desired.
Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
TRF3722 VQFN (48) 7.00 mm x 7.00 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Block Diagram

2
TRF3722
SLWS245B –MAY 2014–REVISED FEBRUARY 2017 www.ti.com
Product Folder Links: TRF3722
Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated
Table of Contents
1 Features.................................................................. 1
2 Applications ........................................................... 1
3 Description............................................................. 1
4 Revision History..................................................... 2
5 Pin Configuration and Functions......................... 3
6 Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings.............................................................. 4
6.3 Recommended Operating Conditions....................... 4
6.4 Thermal Information.................................................. 5
6.5 Electrical Characteristics........................................... 5
6.6 Typical Characteristics.............................................. 9
6.7 Typical Characteristics - Output Power................... 10
6.8 Typical Characteristics - Gain................................. 11
6.9 Typical Characteristics - OIP3 ................................ 12
6.10 Typical Characteristics - OIP2 .............................. 13
6.11 Typical Characteristics - OP1dB........................... 14
6.12 Typical Characteristics - Noise ............................. 15
6.13 Typical Characteristics - Unadjusted CF............... 16
6.14 Typical Characteristics - Unadjusted SBS............ 17
6.15 Typical Characteristics - LO Harmonic ................. 18
6.16 Typical Characteristics - BB Harmonic ................. 20
6.17 Typical Characteristics - RF Output Return Loss . 22
6.18 Typical Characteristics - PLL/VCO ....................... 23
6.19 Typical Characteristics - Current Consumption .... 29
6.20 Typical Characteristics - Power Dissipation.......... 31
7 Parameter Measurement Information ................ 33
7.1 Serial Interface Timing Diagram ............................. 33
8 Detailed Description............................................ 35
8.1 Overview................................................................. 35
8.2 Functional Block Diagram....................................... 35
8.3 Feature Description................................................. 36
8.4 Device Functional Modes........................................ 39
8.5 Register Maps ........................................................ 42
9 Application and Implementation ........................ 55
9.1 Application Information............................................ 55
9.2 Typical Application.................................................. 55
10 Power Supply Recommendations ..................... 58
11 Layout................................................................... 59
11.1 Layout Guidelines ................................................. 59
11.2 Layout Example .................................................... 59
12 Device and Documentation Support................. 60
12.1 Receiving Notification of Documentation Updates 60
12.2 Community Resources.......................................... 60
12.3 Trademarks........................................................... 60
12.4 Electrostatic Discharge Caution............................ 60
12.5 Glossary................................................................ 60
13 Mechanical, Packaging, and Orderable
Information........................................................... 60
4 Revision History
Changes from Revision A (June 2014) to Revision B Page
• Changed 256 MHz to 280 MHz in PLL and VCO Features bullet.......................................................................................... 1
• Changed ESD Ratings table title, updated to current standards ........................................................................................... 4
• Added Typical and footnote 2 to Typical VCO frequency range and Typical output frequency range parameters............... 8
• Changed Figure 1 .................................................................................................................................................................. 9
• Changed location of TRF3722 Application Schematic figure and all associated text to be under Typical Application
section .................................................................................................................................................................................. 55
Changes from Original (May 2014) to Revision A Page
• Changed from 1-page Product Preview to Production........................................................................................................... 1

GND
LD
VCC_DIG
VCC_LO1
GND
NC
BBQ_P
BBQ_N
VCC_MOD1 VCC_MOD2
RFOUT
VCC_MOD3 VCC_MOD4
VCC_TK
VTUNE
NC
BBI_P
NC
GND
GND
GND GND GND GND
GND
PD
RDBK
NC
NC
GND
NC
NC
EXT_VCO
VCC_LO2
VCC_VCO
BBI_N
TRF3722
1
2
3
4
5
6
7
8
9
10
11
12
44 45 46 47 48 39 40 41 42 43 37 38
13 14 15 16 17 18 19 20 21 22 23 24
36
35
34
33
32
31
30
29
28
27
26
25
DATA GND CP_OUT VCC_PLL LO_OUTP GND CLK LO_OUTN REFIN LE GND GND
3
TRF3722
www.ti.com SLWS245B –MAY 2014–REVISED FEBRUARY 2017
Product Folder Links: TRF3722
Submit Documentation FeedbackCopyright © 2014–2017, Texas Instruments Incorporated
5 Pin Configuration and Functions
RGZ Package
48-Pin VQFN
Top View
Pin Functions
PIN I/O DESCRIPTION
NAME NO.
BBI_N 29 I BB in-phase input: negative
BBI_P 27 I BB in-phase input: positive
BBQ_N 8 I BB quadrature input: negative
BBQ_P 10 I BB quadrature input: positive
CLK 48 I Serial interface clock input; digital input
CP_OUT 41 O Charge pump output
DATA 47 I Serial interface data input; digital input
EXT_VCO 31 I External local oscillator input
GND 5, 7, 11, 15, 17, 19, 20, 22, 26, 30, 37, 40, 43,
45 Ground
LD 3 O PLL lock detect output
LE 46 I Serial interface latch enable; digital input
LO_OUTN 38 O Local oscillator output: negative
LO_OUTP 39 O Local oscillator output: positive
NC 9, 12, 13, 24, 25, 36 No connect
NC 28 No connect; N/C or ground to paddle

4
TRF3722
SLWS245B –MAY 2014–REVISED FEBRUARY 2017 www.ti.com
Product Folder Links: TRF3722
Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated
Pin Functions (continued)
PIN I/O DESCRIPTION
NAME NO.
PD 1 I LO Div, TX Div, modulator power down (High = PD)
RDBK 2 O Serial interface internal registers readback output
REFIN 44 I Reference clock input
RFOUT 18 O RF output
VCC_DIG 4 3.3 V digital power supply
VCC_LO1 6 3.3 V TX Div power supply
VCC_LO2 35 3.3 V LO Div power supply
VCC_MOD1 14 3.3 V modulator power supply
VCC_MOD2 16 3.3 V modulator power supply
VCC_MOD3 21 3.3 V modulator power supply
VCC_MOD4 23 3.3 V modulator power supply
VCC_PLL 42 3.3 V PLL power supply
VCC_TK 32 3.3 V or 5 V VCO tank power supply
VCC_VCO 33 3.3 V VCO power supply
VTUNE 34 I VCO control voltage input
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
Supply voltage All VCC except VCC_TK –0.3 +3.6 V
VCC_TK –0.3 +5.5
Digital I/O voltage –0.3 3.6 V
Operating junction temperature –40 150 °C
Storage temperature, Tstg –40 150 °C
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.2 ESD Ratings VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 V
Charged-device model (CDM), per JEDEC specification JESD22-C101(2) ±750
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN NOM MAX UNIT
VCC 3.3 V power-supply voltage 3 3.3 3.6 V
5 V or 3.3 V power-supply voltage, VCC _TK 3 3.3/5 5.5 V
TJOperating junction temperature range –40 125 °C
TAAmbient temperature range –40 85 °C

5
TRF3722
www.ti.com SLWS245B –MAY 2014–REVISED FEBRUARY 2017
Product Folder Links: TRF3722
Submit Documentation FeedbackCopyright © 2014–2017, Texas Instruments Incorporated
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.4 Thermal Information
THERMAL METRIC(1) TRF3722 UNITRGZ (VQFN)
48 PINS
RθJA Junction-to-ambient thermal resistance 27.5 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 12.8 °C/W
RθJB Junction-to-board thermal resistance 4.3 °C/W
ψJT Junction-to-top characterization parameter 0.2 °C/W
ψJB Junction-to-board characterization parameter 4.3 °C/W
RθJC(bot) Junction-to-case (bottom) thermal resistance 0.8 °C/W
(1) Powered down output buffer and LO divider.
6.5 Electrical Characteristics
Over recommended operating conditions: VCC = 3.3 V, VCC_TK = 5 V, TA= 25°C. Optimized bias settings as per Table 16.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
DC PARAMETERS
ICC 3.3 V Supply Current Typical Operating Mode; LO out = Off 328(1) mA
Typical Operating Mode; LO out = On 374 mA
ICC_TK 5 V Supply Current 21 mA
PDISS Total Power Dissipation
Typical Operating Mode; LO out = Off 1.18 W
Typical Operating Mode; LO out = On 1.34 W
Low Power Mode (Mod); LO out = Off 0.91 W
IPD Power Down Current Hardware Power Down 76 mA
Serial interface Power Down 2 mA
RFOUT FREQUENCY
Frequency 400 4200 MHz
IQ MODULATOR ƒLO = 750 MHz
GGain Typical Operating Mode 0.8 dB High Gain Mode 3.6 dB
Gain Flatness In 300MHz bandwidth –0.5 0.5 dB
OP1dB Output Compression Point 10.2 dBm
OIP3 Output 3rd Order Intercept Point FBB = 4.5, 5.5 MHz 31 dBm
OIP2 Output 2nd Order Intercept Point FBB = 4.5, 5.5 MHz 62 dBm
SBS Unadj. SideBand Suppression –42 dBc
CF Unadj. Carrier Feedthrough –50 dBm
NSDOOutput Noise Spectral Density BB inputs terminated on 50 Ω–159 dBm/Hz
HD2LO LO Second Harmonic Measured at 2 x fLO –49 dBc
HD3LO LO Third Harmonic Measured at 3 x fLO –47 dBc
HD2BB Baseband Second Harmonic Measured at fLO ± 2 x fBB –72 dBc
HD3BB Baseband Third Harmonic Measured at fLO ± 3 x fBB –70 dBc

6
TRF3722
SLWS245B –MAY 2014–REVISED FEBRUARY 2017 www.ti.com
Product Folder Links: TRF3722
Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated
Electrical Characteristics (continued)
Over recommended operating conditions: VCC = 3.3 V, VCC_TK = 5 V, TA= 25°C. Optimized bias settings as per Table 16.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
IQ MODULATOR ƒLO = 900 MHz
GGain Typical Operating Mode 0.8 dB High Gain Mode 3.6 dB
Gain Flatness In 300MHz bandwidth –0.5 0.5 dB
OP1dB Output Compression Point 10 dBm
OIP3 Output 3rd Order Intercept Point FBB = 4.5, 5.5 MHz 31 dBm
OIP2 Output 2nd Order Intercept Point FBB = 4.5, 5.5 MHz 62.5 dBm
SBS Unadj. Side Band Suppression –42.5 dBc
CF Unadj. Carrier Feed through –50 dBm
NSDOOutput Noise Spectral Density BB inputs terminated on 50 Ω–159 dBm/Hz
HD2LO LO Second Harmonic Measured at 2 x fLO –47 dBc
HD3LO LO Third Harmonic Measured at 3 x fLO –54.5 dBc
HD2BB Baseband Second Harmonic Measured at fLO ± 2 x fBB –65.5 dBc
HD3BB Baseband Third Harmonic Measured at fLO ± 3 x fBB –71.5 dBc
IQ MODULATOR ƒLO = 1800 MHz
GGain Typical Operating Mode 0.3 dB High Gain Mode 3 dB
Gain Flatness In 300 MHz bandwidth –0.5 0.5 dB
OP1dB Output Compression Point 13 dBm
OIP3 Output 3rd Order Intercept Point fBB = 4.5, 5.5 MHz 29.5 dBm
OIP2 Output 2nd Order Intercept Point fBB = 4.5, 5.5 MHz 57 dBm
SBS Unadj. Side Band Suppression –54.5 dBc
CF Unadj. Carrier Feed through –57 dBm
NSDOOutput Noise Spectral Density BB inputs terminated on 50 Ω–158 dBm/Hz
HD2LO LO Second Harmonic Measured at 2 x fLO –36.5 dBc
HD3LO LO Third Harmonic Measured at 3 x fLO –33.5 dBc
HD2BB Baseband Second Harmonic Measured at fLO ± 2 x fBB –65.5 dBc
HD3BB Baseband Third Harmonic Measured at fLO ± 3 x fBB –73 dBc
RLORF Output Return Loss 6 dB
IQ MODULATOR ƒLO = 2150 MHz
GGain Typical Operating Mode 0.2 dB High Gain Mode 3 dB
Gain Flatness In 300 MHz bandwidth –0.5 0.5 dB
OP1dB Output Compression Point 11.6 dBm
OIP3 Output 3rd Order Intercept Point FBB = 4.5, 5.5 MHz 30 dBm
OIP2 Output 2nd Order Intercept Point FBB = 4.5, 5.5 MHz 43 dBm
SBS Unadj. Side Band Suppression –43 dBc
CF Unadj. Carrier Feedt hrough –42 dBm
NSDOOutput Noise Spectral Density BB inputs terminated on 50 Ω–157 dBm/Hz
HD2LO LO Second Harmonic Measured at 2 x fLO –40 dBc
HD3LO LO Third Harmonic Measured at 3 x fLO –31 dBc
HD2BB Baseband Second Harmonic Measured at fLO ± 2 x fBB –51 dBc
HD3BB Baseband Third Harmonic Measured at fLO ± 3 x fBB –69 dBc

7
TRF3722
www.ti.com SLWS245B –MAY 2014–REVISED FEBRUARY 2017
Product Folder Links: TRF3722
Submit Documentation FeedbackCopyright © 2014–2017, Texas Instruments Incorporated
Electrical Characteristics (continued)
Over recommended operating conditions: VCC = 3.3 V, VCC_TK = 5 V, TA= 25°C. Optimized bias settings as per Table 16.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
IQ MODULATOR ƒLO = 2700 MHz
GGain Typical Operating Mode 0 dB High Gain Mode 2.4 dB
Gain Flatness In 300MHz bandwidth –0.5 0.5 dB
OP1dB Output Compression Point 10.4 dBm
OIP3 Output 3rd Order Intercept Point FBB = 4.5, 5.5 MHz 29.5 dBm
OIP2 Output 2nd Order Intercept Point FBB = 4.5, 5.5 MHz 45.5 dBm
SBS Unadj. Side Band Suppression –33 dBc
CF Unadj. Carrier Feed through –39.6 dBm
NSDOOutput Noise Spectral Density BB inputs terminated on 50 Ω–156 dBm/Hz
HD2LO LO Second Harmonic Measured at 2 x fLO –29 dBc
HD3LO LO Third Harmonic Measured at 3 x fLO –37 dBc
HD2BB Baseband Second Harmonic Measured at fLO ± 2 x fBB –53 dBc
HD3BB Baseband Third Harmonic Measured at fLO ± 3 x fBB –68 dBc
IQ MODULATOR ƒLO = 3600 MHz
G Gain Typical Operating Mode –2 dB
High Gain Mode 0.4 dB
OP1dB Output Compression Point 8.7 dBm
OIP3 Output 3rd Order Intercept Point FBB = 4.5, 5.5 MHz 24.5 dBm
OIP2 Output 2nd Order Intercept Point FBB = 4.5, 5.5 MHz 45.5 dBm
SBS Unadj. Side Band Suppression –31.5 dBc
CF Unadj. Carrier Feed through –39.5 dBm
HD2LO LO Second Harmonic Measured at 2 x fLO –28.4 dBc
HD3LO LO Third Harmonic Measured at 3 x fLO –31.5 dBc
HD2BB Baseband Second Harmonic Measured at fLO ± 2 x fBB –55 dBc
HD3BB Baseband Third Harmonic Measured at fLO ± 3 x fBB –65 dBc
BASEBAND INPUTS
VCM Common Mode Voltage Baseband I/Q input 0 0.25 0.5 V
BWBB Baseband Bandwidth 1 dB Bandwidth 900 MHz
ZinBB Baseband Input Impedance Resistance 5 kΩ
Capacitance 4 pF
REFERENCE OSCILLATOR PARAMETERS
Fref Reference Frequency Max 350 MHz
Reference Input Sensitivity 0.2 3.3 VPP
Zinref Reference Input Impedance Parallel capacitance 2 pF
Parallel resistance 2.2 kΩ
PFD, CP
FPFD PFD Frequency Max, refer to the Typical Application 65 MHz
ICP_OUT Charge Pump Current Max 1.94 mA
In-band Normalized PN Floor Integer Mode –221 dBc/Hz

8
TRF3722
SLWS245B –MAY 2014–REVISED FEBRUARY 2017 www.ti.com
Product Folder Links: TRF3722
Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated
Electrical Characteristics (continued)
Over recommended operating conditions: VCC = 3.3 V, VCC_TK = 5 V, TA= 25°C. Optimized bias settings as per Table 16.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
(2) Divided-down ranges minimum and maximum values are typical but are not specified.
VCO
fVCO Typical VCO frequency range(2) 2050 4100 MHz
KVVCO gain VTUNE = 1.1 V 30 MHz/V
PN
VCO Open Loop Phase Noise;
fVCO = 3600 MHz;
TX Div = Div-by-1;
fOUT = 3600 MHz
VTUNE = 1.1 V
10 kHz –74
dBc/Hz
100 kHz –109
1 MHz –135
10 MHz –152
40 MHz –156
VCO Open Loop Phase Noise;
fVCO = 3600 MHz;
TX Div = Div-by-2;
fOUT = 1800 MHz;
VTUNE = 1.1 V
10 kHz –80
dBc/Hz
100 kHz –115
1 MHz –141
10 MHz –156
40 MHz –158
LO OUTPUT
fOUT Typical output frequency range(2)
Divide by 1 2050 4100
MHz
Divide by 2 1025 2050
Divide by 4 512.5 1025
Divide by 8 256.25 512.5
PLO Output power SE at 1800 MHz, OUTBUF_BIAS = 2 1 dBm
External VCO input Frequency Range 250 4200 MHz
External VCO Input Level –10 0 10 dBm
CLOSE LOOP PLL OR VCO
Integrated Phase Noise
Frac-N; PFD = 15.36 MHz; fOUT =
3532.89 MHz;
Integration BW =1 kHz to 10 MHz; SSB -45.2 dB
Int-N; PFD = 2.56 MHz; fOUT = 1799.68
MHz;
Integration BW = 500 Hz to 20 MHz; SSB -49.8 dB
VCO Close Loop Phase Noise;
fVCO = 3600 MHz;
TX DIV = Div-by-2;
fOUT = 1800 MHz;
Integer Mode, PFD = 2.56MHz
10 kHz –96
dBc/Hz
100 kHz –114
1 MHz –140
10 MHz –156
40 MHz –158
DIGITAL INTERFACE
VIH High Level Input Voltage 2 3.3 V
VIL Low Level Input Voltage 0 0.8 V
VOH High Level Output Voltage Referenced to VCC_DIG 0.8 x VCC V
VOL Low Level Output Voltage Referenced to VCC_DIG 0.2 x VCC V

F1 = FBB1+ LO
F2 = FBB2+ LO
F3rdL = 2F1-F2
F3rdH = 2F2-F1
F2ndL = (FBB2 -FBB1)+LO
F2ndH = (FBB2 + FBB1)+LO
LO
LSB1 = LO -FBB1
LSB2 = LO ±FBB2
FBBn = Baseband Frequency
Fn = RF Frequency
F3rdH/L = 3rd Order Intermodulation Product Frequency (High Side / Low Side)
F2ndH/L = 2nd Order Intermodulation Product Frequency (High Side / Low Side)
LO = Local Oscillator Frequency
LSBn = Lower Sideband Frequency
HD2BB = Baseband second harmonic (High Side / Low Side)
HD3BB = Baseband thrid harmonic (High Side / Low Side)
Desired Signal
Unwanted Sideband
3rd Order IM
2nd Order IM
Freq.
HD2BB
HD3BB
LO + 3FBB1
LO + 3FBB2
LO - 3FBB2 LO - 3FBB1
LO - 2FBB1 LO - 2FBB2
LO + 2FBB2
LO + 2FBB1
9
TRF3722
www.ti.com SLWS245B –MAY 2014–REVISED FEBRUARY 2017
Product Folder Links: TRF3722
Submit Documentation FeedbackCopyright © 2014–2017, Texas Instruments Incorporated
6.6 Typical Characteristics
6.6.1 Modulator Output Spectrum
Graphical illustration of the modulator output spectrum with two tones is shown in Figure 1.
Figure 1. Graphical Illustration of Modulator Output Spectrum

Frequency (MHz)
POUT (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-10
-8
-6
-4
-2
0
2
4
6
D019
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
POUT (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-10
-8
-6
-4
-2
0
2
4
6
D220
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
POUT (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-10
-8
-6
-4
-2
0
2
4
6
D017
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
POUT (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-10
-8
-6
-4
-2
0
2
4
6
D219
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
POUT (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-10
-8
-6
-4
-2
0
2
4
6
D015
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
POUT (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-10
-8
-6
-4
-2
0
2
4
6
D218
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
10
TRF3722
SLWS245B –MAY 2014–REVISED FEBRUARY 2017 www.ti.com
Product Folder Links: TRF3722
Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated
6.7 Typical Characteristics - Output Power
Unless specified all plots were created using TRF3722EVM, VCC = 3.3 V, VCC_TK = 5 V, TA= 25°C, I/Q frequency (fBB)
4.5 MHz and 5.5 MHz, 500 mVPP, VCM = 0.25 V, and 4.7 pF series capacitor at RFOUT. Optimized bias settings as per
Table 16. Total Pout is two tones combined power.
Figure 2. Total POUT vs Temperature, Typical Operating
Mode Figure 3. Total POUT vs Supply, Typical Operating Mode
Figure 4. Total POUT vs Temperature, High Gain Mode Figure 5. Total POUT vs Supply, High Gain Mode
Figure 6. Total POUT vs Temperature, Low Power Mode Figure 7. Total POUT vs Supply, Low Power Mode

Frequency (MHz)
G (dB)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-10
-8
-6
-4
-2
0
2
4
6
D007
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
G (dB)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-10
-8
-6
-4
-2
0
2
4
6
D008
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
G (dB)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-10
-8
-6
-4
-2
0
2
4
6
D005
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
G (dB)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-10
-8
-6
-4
-2
0
2
4
6
D006
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
G (dB)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-10
-8
-6
-4
-2
0
2
4
6
D003
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
G (dB)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-10
-8
-6
-4
-2
0
2
4
6
D004
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
11
TRF3722
www.ti.com SLWS245B –MAY 2014–REVISED FEBRUARY 2017
Product Folder Links: TRF3722
Submit Documentation FeedbackCopyright © 2014–2017, Texas Instruments Incorporated
6.8 Typical Characteristics - Gain
Unless specified all plots were created using TRF3722EVM, VCC = 3.3 V, VCC_TK = 5 V, TA= 25°C, I/Q frequency (fBB)
4.5 MHz and 5.5 MHz, VCM = 0.25 V, and 4.7 pF series capacitor at RFOUT. Optimized bias settings as per Table 16.
Figure 8. Voltage Gain vs Temperature, Typical Operating
Mode Figure 9. Voltage Gain vs Supply, Typical Operating Mode
Figure 10. Voltage Gain vs Temperature, High Gain Mode Figure 11. Voltage Gain vs Supply, High Gain Mode
Figure 12. Voltage Gain vs Temperature, Low Power Mode Figure 13. Voltage Gain vs Supply, Low Power Mode

Frequency (MHz)
OIP3 (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
16
18
20
22
24
26
28
30
32
34
D013
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
OIP3 (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
16
18
20
22
24
26
28
30
32
34
D014
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
OIP3 (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
16
18
20
22
24
26
28
30
32
34
D011
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
OIP3 (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
16
18
20
22
24
26
28
30
32
34
D012
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
OIP3 (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
16
18
20
22
24
26
28
30
32
34
D009
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
OIP3 (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
16
18
20
22
24
26
28
30
32
34
D010
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
12
TRF3722
SLWS245B –MAY 2014–REVISED FEBRUARY 2017 www.ti.com
Product Folder Links: TRF3722
Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated
6.9 Typical Characteristics - OIP3
Unless specified all plots were created using TRF3722EVM, VCC = 3.3 V, VCC_TK = 5 V, TA= 25°C, I/Q frequency (fBB)
4.5 MHz and 5.5 MHz, VCM = 0.25 V, and 4.7 pF series capacitor at RFOUT. Optimized bias settings as per Table 16.
Reported OIP3 is minimum of low side and high side.
Figure 14. OIP3 vs Temperature, Typical Operating Mode Figure 15. OIP3 vs Supply, Typical Operating Mode
Figure 16. OIP3 vs Temperature, High Gain Mode Figure 17. OIP3 vs Supply, High Gain Mode
Figure 18. OIP3 vs Temperature, Low Power Mode Figure 19. OIP3 vs Supply, Low Power Mode

Frequency (MHz)
OIP2 (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
30
35
40
45
50
55
60
65
70
D025
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
OIP2 (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
30
35
40
45
50
55
60
65
70
D026
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
OIP2 (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
30
35
40
45
50
55
60
65
70
D023
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
OIP2 (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
30
35
40
45
50
55
60
65
70
D024
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
OIP2 (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
30
35
40
45
50
55
60
65
70
D021
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
OIP2 (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
30
35
40
45
50
55
60
65
70
D022
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
13
TRF3722
www.ti.com SLWS245B –MAY 2014–REVISED FEBRUARY 2017
Product Folder Links: TRF3722
Submit Documentation FeedbackCopyright © 2014–2017, Texas Instruments Incorporated
6.10 Typical Characteristics - OIP2
Unless specified all plots were created using TRF3722EVM, VCC = 3.3 V, VCC_TK = 5 V, TA= 25°C, I/Q frequency (fBB)
4.5 MHz and 5.5 MHz, VCM = 0.25 V, and 4.7 pF series capacitor at RFOUT. Optimized bias settings as per Table 16.
Reported OIP2 is minimum of low side and high side.
Figure 20. OIP2 vs Temperature, Typical Operating Mode Figure 21. OIP2 vs Supply, Typical Operating Mode
Figure 22. OIP2 vs Temperature, High Gain Mode Figure 23. OIP2 vs Supply, High Gain Mode
Figure 24. OIP2 vs Temperature, Low Power Mode Figure 25. OIP2 vs Supply, Low Power Mode

Frequency (MHz)
OP1dB (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-2
0
2
4
6
8
10
12
14
16
D031
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
OP1dB (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-2
0
2
4
6
8
10
12
14
16
D032
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
OP1dB (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-2
0
2
4
6
8
10
12
14
16
D029
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
OP1dB (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-2
0
2
4
6
8
10
12
14
16
D030
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
OP1dB (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-2
0
2
4
6
8
10
12
14
16
D027
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
OP1dB (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-2
0
2
4
6
8
10
12
14
16
D028
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
14
TRF3722
SLWS245B –MAY 2014–REVISED FEBRUARY 2017 www.ti.com
Product Folder Links: TRF3722
Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated
6.11 Typical Characteristics - OP1dB
Unless specified all plots were created using TRF3722EVM, VCC = 3.3 V, VCC_TK = 5 V, TA= 25°C, I/Q frequency (fBB)
5 MHz, VCM = 0.25 V, and 4.7 pF series capacitor at RFOUT. Optimized bias settings as per Table 16.
Figure 26. OP1dB vs Temperature, Typical Operating Mode Figure 27. OP1dB vs Supply, Typical Operating Mode
Figure 28. OP1dB vs Temperature, High Gain Mode Figure 29. OP1dB vs Supply, High Gain Mod
Figure 30. OP1dB vs Temperature, Low Power Mode Figure 31. OP1dB vs Supply, Low Power Mode

Frequency (MHz)
NSD (dBm/Hz)
200 600 1000 1400 1800 2200 2600
-170
-168
-166
-164
-162
-160
-158
-156
-154
-152
-150
D049
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
NSD (dBm/Hz)
200 600 1000 1400 1800 2200 2600
-170
-168
-166
-164
-162
-160
-158
-156
-154
-152
-150
D050
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
NSD (dBm/Hz)
200 600 1000 1400 1800 2200 2600
-170
-168
-166
-164
-162
-160
-158
-156
-154
-152
-150
D047
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
NSD (dBm/Hz)
200 600 1000 1400 1800 2200 2600
-170
-168
-166
-164
-162
-160
-158
-156
-154
-152
-150
D048
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
NSD (dBm/Hz)
200 600 1000 1400 1800 2200 2600
-170
-168
-166
-164
-162
-160
-158
-156
-154
-152
-150
D045
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
NSD (dBm/Hz)
200 600 1000 1400 1800 2200 2600
-170
-168
-166
-164
-162
-160
-158
-156
-154
-152
-150
D046
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
15
TRF3722
www.ti.com SLWS245B –MAY 2014–REVISED FEBRUARY 2017
Product Folder Links: TRF3722
Submit Documentation FeedbackCopyright © 2014–2017, Texas Instruments Incorporated
6.12 Typical Characteristics - Noise
Unless specified all plots were created using TRF3722EVM, VCC = 3.3 V, VCC_TK = 5 V, TA= 25°C, BB inputs terminated to
50 Ωand 4.7 pF series capacitor at RFOUT. Optimized bias settings as per Table 16.
Figure 32. Noise vs Temperature, Typical Operating Mode Figure 33. Noise vs Supply, Typical Operating Mode
Figure 34. Noise vs Temperature, High Gain Mode Figure 35. Noise vs Supply, High Gain Mode
Figure 36. Noise vs Temperature, Low Power Mode Figure 37. Noise vs Supply, Low Power Mode

Frequency (MHz)
Unadj. CF (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-80
-75
-70
-65
-60
-55
-50
-45
-40
-35
-30
D037
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
Unadj. CF (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-80
-75
-70
-65
-60
-55
-50
-45
-40
-35
-30
D038
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
Unadj. CF (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-70
-65
-60
-55
-50
-45
-40
-35
-30
D035
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
Unadj. CF (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-70
-65
-60
-55
-50
-45
-40
-35
-30
D036
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
Unadj. CF (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-70
-65
-60
-55
-50
-45
-40
-35
-30
D033
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
Unadj. CF (dBm)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-70
-65
-60
-55
-50
-45
-40
-35
-30
D034
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
16
TRF3722
SLWS245B –MAY 2014–REVISED FEBRUARY 2017 www.ti.com
Product Folder Links: TRF3722
Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated
6.13 Typical Characteristics - Unadjusted CF
Unless specified all plots were created using TRF3722EVM, VCC = 3.3 V, VCC_TK= 5 V, TA= 25°C, I/Q frequency (fBB)
4.5 MHz and 5.5 MHz, VCM = 0.25 V, and 4.7 pF series capacitor at RFOUT. Optimized bias settings as per Table 16.
Figure 38. Unadjustable CF vs Temperature,
Typical Operating Mode Figure 39. Unadjustable CF vs Supply, Typical Operating Mode
Figure 40. Unadjustable CF vs Temperature,
High Gain Mode Figure 41. Unadjustable CF vs Supply, High Gain Mode
Figure 42. Unadjustable CF vs Temperature,
Low Power Mode Figure 43. Unadjustable CF vs Supply, Low Power Mode

Frequency (MHz)
Unadj. SBS (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-60
-55
-50
-45
-40
-35
-30
-25
D225
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
Unadj. SBS (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-60
-55
-50
-45
-40
-35
-30
-25
D226
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
Unadj. SBS (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-60
-55
-50
-45
-40
-35
-30
-25
D223
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
Unadj. SBS (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-60
-55
-50
-45
-40
-35
-30
-25
D224
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
Unadj. SBS (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-60
-55
-50
-45
-40
-35
-30
-25
D221
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
Unadj. SBS (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-60
-55
-50
-45
-40
-35
-30
-25
D222
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
17
TRF3722
www.ti.com SLWS245B –MAY 2014–REVISED FEBRUARY 2017
Product Folder Links: TRF3722
Submit Documentation FeedbackCopyright © 2014–2017, Texas Instruments Incorporated
6.14 Typical Characteristics - Unadjusted SBS
Unless specified all plots were created using TRF3722EVM, VCC = 3.3 V, VCC_TK= 5 V, and TA= 25°C, I/Q frequency (fBB)
4.5 MHz and 5.5 MHz, VCM = 0.25 V, and 4.7 pF series capacitor at RFOUT. Optimized bias settings as per Table 16.
Figure 44. Unadjustable SBS vs Temperature,
Typical Operating Mode Figure 45. Unadjustable SBS vs Supply, Typical Operating Mode
Figure 46. Unadjustable SBS vs
Temperature, High Gain Mode Figure 47. Unadjustable SBS vs Supply, High Gain Mode
Figure 48. Unadjustable SBS vs Temperature,
Low Power Mode Figure 49. Unadjustable SBS vs Supply, Low Power Mode

Frequency (MHz)
HD2LO (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-60
-55
-50
-45
-40
-35
-30
-25
-20
D055
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
HD2LO (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-60
-55
-50
-45
-40
-35
-30
-25
-20
D203
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
HD2LO (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-60
-55
-50
-45
-40
-35
-30
-25
-20
D053
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
HD2LO (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-60
-55
-50
-45
-40
-35
-30
-25
-20
D202
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
HD2LO (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-60
-55
-50
-45
-40
-35
-30
-25
-20
D051
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
HD2LO (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-60
-55
-50
-45
-40
-35
-30
-25
-20
D201
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
18
TRF3722
SLWS245B –MAY 2014–REVISED FEBRUARY 2017 www.ti.com
Product Folder Links: TRF3722
Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated
6.15 Typical Characteristics - LO Harmonic
Unless specified all plots were created using TRF3722EVM, VCC = 3.3 V, VCC_TK = 5 V, and TA= 25°C, I/Q frequency (fBB)
4.5 MHz and 5.5 MHz, VCM = 0.25 V, and 4.7 pF series capacitor at RFOUT. Optimized bias settings as per Table 16.
Figure 50. LO Second Harmonic vs Temperature,
Typical Operating Mode Figure 51. LO Second Harmonic vs Supply, Typical Operating Mode
Figure 52. LO Second Harmonic vs Temperature,
High Gain Mode Figure 53. LO Second Harmonic vs Supply, High Gain Mode
Figure 54. LO Second Harmonic vs Temperature,
Low Power Mode Figure 55. LO Second Harmonic vs Supply, Low Power Mode

Frequency (MHz)
HD3LO (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-80
-75
-70
-65
-60
-55
-50
-45
-40
-35
-30
-25
D061
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
HD3LO (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-80
-75
-70
-65
-60
-55
-50
-45
-40
-35
-30
-25
D206
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
HD3LO (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-80
-75
-70
-65
-60
-55
-50
-45
-40
-35
-30
-25
D059
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
HD3LO (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-80
-75
-70
-65
-60
-55
-50
-45
-40
-35
-30
-25
D205
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
HD3LO (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-80
-75
-70
-65
-60
-55
-50
-45
-40
-35
-30
-25
D057
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
HD3LO (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-80
-75
-70
-65
-60
-55
-50
-45
-40
-35
-30
-25
D204
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
19
TRF3722
www.ti.com SLWS245B –MAY 2014–REVISED FEBRUARY 2017
Product Folder Links: TRF3722
Submit Documentation FeedbackCopyright © 2014–2017, Texas Instruments Incorporated
Typical Characteristics - LO Harmonic (continued)
Unless specified all plots were created using TRF3722EVM, VCC = 3.3 V, VCC_TK = 5 V, and TA= 25°C, I/Q frequency (fBB)
4.5 MHz and 5.5 MHz, VCM = 0.25 V, and 4.7 pF series capacitor at RFOUT. Optimized bias settings as per Table 16.
Figure 56. LO Third Harmonic vs Temperature,
Typical Operating Mode Figure 57. LO Third Harmonic vs Supply, Typical Operating Mode
Figure 58. LO Third Harmonic vs Temperature,
High Gain Mode Figure 59. LO Third Harmonic vs Supply, High Gain Mode
Figure 60. LO Third Harmonic vs Temperature,
Low Power Mode Figure 61. LO Third Harmonic vs Supply, Low Power Mode

Frequency (MHz)
HD2BB (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-80
-75
-70
-65
-60
-55
-50
-45
-40
D067
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
HD2BB (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-80
-75
-70
-65
-60
-55
-50
-45
-40
D209
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
HD2BB (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-80
-75
-70
-65
-60
-55
-50
-45
-40
D065
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
HD2BB (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-80
-75
-70
-65
-60
-55
-50
-45
-40
D208
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
Frequency (MHz)
HD2BB (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-80
-75
-70
-65
-60
-55
-50
-45
-40
D063
TA= -40qC
TA= 25qC
TA= 85qC
Frequency (MHz)
HD2BB (dBc)
0 500 1000 1500 2000 2500 3000 3500 4000 4500
-80
-75
-70
-65
-60
-55
-50
-45
-40
D207
VCC = 3.15V, 4.75V
VCC = 3.30V, 5.00V
VCC = 3.45V, 5.25V
20
TRF3722
SLWS245B –MAY 2014–REVISED FEBRUARY 2017 www.ti.com
Product Folder Links: TRF3722
Submit Documentation Feedback Copyright © 2014–2017, Texas Instruments Incorporated
6.16 Typical Characteristics - BB Harmonic
Unless specified all plots were created using TRF3722EVM, VCC = 3.3 V, VCC_TK= 5 V, and TA= 25°C, I/Q frequency (fBB)
4.5 MHz and 5.5 MHz, VCM = 0.25 V, and 4.7 pF series capacitor at RFOUT. Optimized bias settings as per Table 16.
Reported BB harmonic is from (fBB) 4.5MHz.
Figure 62. BB-HD2 vs Temperature, Typical Operating Mode Figure 63. BB-HD2 vs Supply, Typical Operating Mode
Figure 64. BB-HD2 vs Temperature, High Gain Mode Figure 65. BB-HD2 vs Supply, High Gain Mode
Figure 66. BB-HD2 vs Temperature, Low Power Mode Figure 67. BB-HD2 vs Supply, Low Power Mode