Texas Instruments DAC7741EVM User manual

User's GuideSLAU093A – October 2002 – Revised May 2005
DAC7741EVM
This user’s guide describes the DAC7741 evaluation module. It covers the operatingprocedures and characteristics of the EVM board along with the device that it supports.The physical PCB layout, schematic diagram, and circuit descriptions are included.
Contents1 Information About Cautions and Warnings ...................................................... 22 Related Documentation from Texas Instruments ............................................... 23 Questions about this or other Data Converter EVM's? ........................................ 24 FCC Warnings ...................................................................................... 2Trademarks .......................................................................................... 25 EVM Overview ...................................................................................... 36 EVM Basic Functions .............................................................................. 47 Physical Description ................................................................................ 58 Bill Of Materials .................................................................................... 129 EVM Operation .................................................................................... 13
List of Figures
1 EVM Block Diagram ................................................................................ 42 Top Silkscreen ...................................................................................... 53 Layer One (Top Signal Plane) .................................................................... 64 Layer Two (Split Ground Plane) .................................................................. 75 Layer Three (Split Power Plane) ................................................................. 86 Layer Four (Bottom Signal Plane) ................................................................ 97 Bottom Silkscreen ................................................................................. 108 Drill Drawing ....................................................................................... 11
List of Tables
1 Parts List ........................................................................................... 122 Factory Default Jumper Settings ................................................................ 133 Unity Gain Output Jumper Settings ............................................................. 144 Gain of Two Output Jumper Settings ........................................................... 155 Capacitive Load Drive Output Jumper Settings ............................................... 156 Jumper Setting Function ......................................................................... 16
DAC7741EVMSLAU093A – October 2002 – Revised May 2005 1

www.ti.com
1 Information About Cautions and Warnings
2 Related Documentation from Texas Instruments
3 Questions about this or other Data Converter EVM's?
4 FCC Warnings
Trademarks
Information About Cautions and Warnings
This manual may contain cautions and warnings.
CAUTIONThis is an example of a CAUTION statement.
A CAUTION statement describes a situation that could potentially damage thisEVM board, your software, or equipment.
WARNINGThis is an example of a WARNING statement.
A WARNING statement describes a situation that could potentially cause HARMto you.
The information in a caution or a warning is provided for your protection. Read each caution and warningcarefully.
To obtain a copy of any of the following TI documents, call the Texas Instruments Literature ResponseCenter at [phone] or the Product Information Center (PIC) at [phone]. When ordering,identify this manual by its title and literature number. Updated documents can also be obtained throughthe TI Web site at http://www.ti.com.
Data Sheets: Literature Number: Data Sheets: Literature Number:DAC7741 SBAS248 SN74AHC541 SCLS261REF102 SBVS022 SN74AHC138 SCLS258OPA627 SBOS165 SN74AHC1G04 SCLS318OPA2277 SBOS079 SN74AHC1G08 SCLS314SN74ALVC16245 SCAS419 SN74AUP1G57 SCES503
If you have questions about this or other Texas Instruments Data Converter evaluation modules, contactthe Data Converter Application Team by e-mail at [email protected]. Include the product you havequestions or concerns with in the subject heading .
This equipment is intended for use in a laboratory test environment only. It generates, uses, and canradiate radio frequency energy and has not been tested for compliance with the limits of computingdevices pursuant to subpart J of part 15 of FCC rules. Operation of this equipment in other environmentsmay cause interference with radio communications, in which case the user at his expense will be requiredto take whatever measures may be required to correct this interference.
TMS320 is a trademark of Texas Instruments.
DAC7741EVM 2 SLAU093A – October 2002 – Revised May 2005

www.ti.com
5 EVM Overview
5.1 Features
5.2 Power Requirements
EVM Overview
This section gives a general overview of the DAC7741 evaluation module (EVM), and describes some ofthe factors that must be considered in using this module.
This EVM features the DAC7741 digital-to-analog converter. The DAC7741 EVM is a simple evaluationmodule designed for a quick and easy way to evaluate the functionality of the high resolution,single-channel, and parallel input DAC. This EVM features a parallel interface to communicate to any hostprocessor base system
The following sections describe the power requirements of this EVM.
5.2.1 Supply Voltage
The dc power supply requirement for the digital section of this EVM is typically 5 V connected to the J12-3or via J6-10 terminal (when plugged in with another EVM board or interface card) and is referenced toground through the J12-2 and J6-5 terminal. The dc power supply requirement for the analog section (V
CCand V
SS
) of this EVM range from 15.75 V to -15.75 V maximum and connects through J11-3 and J11-1 orthrough J6-1 and J6-2 terminals and is referenced to analog ground through J11-2, J12-2, and J6-6terminals.
The dc source of ±15 V supply required to provide the rails for the external output operational amplifier isderived from V
CC
and V
SS
as described above. The output operational amplifier, U2, is used for outputsignal conditioning or boost capacitive load drive and for other output modes of application.
CAUTIONTo avoid potential damage to the EVM board, make sure that the correctcables are connected to their respective terminals as labeled on the EVMboard. Stresses above the maximum listed voltage ratings may causepermanent damage to the device.
5.2.2 Reference Voltage
Although the DAC7741 has a built-in 10-V voltage reference, an external reference circuit is provided inthe EVM board. The external reference circuit can be isolated if the internal reference voltage is selected.
The 10-V precision voltage reference is provided to supply the external voltage reference for the DACthrough REF102, U3, via jumper W4 by shorting pins 1 and 2. An adjustable 100-k Ωpotentiometer, R11,is installed in series with 20-k Ω, R10, to allow the user to adjust the reference voltage to its desiredsettings. TP1 and TP2 are also provided, as well as J2-20 or J4-20 terminals via jumper W31, to allow theuser to connect another external reference source if the onboard reference circuit is not desired. Theexternal voltage reference should not exceed 10-V dc.
The REF102 precision reference derives its supply power of 15 V through J11 or J6 terminal as describedearlier regarding supply voltages.
The DAC7741 has a REFEN pin to enable the internal reference circuit or disable it and select an externalreference source. The REFEN pin can be hardware-driven through W2 jumper. Likewise, it can also besoftware-driven through J3-17 terminal via W2 jumper by shorting pins 1 and 2. The REF
OUT
pin of theDAC7741 must be connected to the REF
IN
pin to use the internal voltage reference. This is done throughthe W3 jumper by shorting pins 1 and 2. Shorting pins 2 and 3 of W3 selects the external voltagereference source.
DAC7741EVMSLAU093A – October 2002 – Revised May 2005 3

www.ti.com
6 EVM Basic Functions
DAC Out
(J2)
(J4)
(J3)
+ 15 V
- 15 V
GND
GND
(J1)
(J6)
(J11)
(J12)
W13
W14
TP1
VCC VCC
VDD VDD
VSS VSS
LDAC
RSTSEL
DB15 (MSB)
DB1 (MSB)
A2...A0
CS
R/W
RST
+ 3.3 V
+ 3.3 V
REFEN
TP2
+REF
Ext Ref
Input
IN
External
Reference
Module
DAC Module
3.3 V
Logic and
Translators
REFIN REFOUT
Output
Buffer
Module
W4
W3
+ 15 V
- 15 V
EVM Basic Functions
The on-chip reference buffer output is funneled out through V
REF
pin, which is used to set up theDAC7741 output amplifier into one of three voltage output modes. V
REF
can also be used to drive othersystem components that require external voltage reference. See the data sheet for more informationregarding the internal reference feature.
CAUTIONWhen applying an external voltage reference through TP1, J2-20, or J4-20,make sure that it does not exceed 14.35 V maximum. Otherwise, this canpermanently damage the DAC7741, U1, device under test.
The DAC7741 EVM is a functional evaluation platform to test certain functional characteristics of theDAC7741 digital-to-analog converter. Functional evaluation of the DAC device can be accomplished withthe use of any microprocessor, TMS320™ DSP family, or some sort of a signal/waveform generator.
The headers, J1 and J3, are provided to connect the necessary control signals and data needed tointerface a microprocessor/microcontroller, TI’s DSP Starter Kit, or waveform generator to the DAC7741EVM. A custom cable can be built for this purpose if using the EVM without the use of TI’s 5-6k interfaceadapter board or the HPA449 platform.
The 5-6k interface adapter board is used for most of TI’s DSP Starter Kits (DSK). Hence, if using theTMS320C5x™ DSP generation and TMS320C6x™ DSP generation DSKs, the 5-6k interface adapterboard proves practical, as no cabling is required. In addition, the HPA449 platform is also available for useif the MSP430 microcontroller is desired as the host processor. Call or e-mail TI for more informationregarding the adapter interface board.
The output of the DAC can be monitored through one of two terminals J2 or J4. Shorting pins 1 and 2 ofjumper W30, allows the DAC output to be seen on J4 pins 2, 4, 6, and 8. The 6-pin header, W13, providesdifferent options of the DAC output, but requires the output operational amplifier, U2, to first be configuredcorrectly for the desired waveform characteristic. Shorting pins 1 and 2 of W13 allows the user to monitorthe raw output of the DAC7741.
A block diagram of the EVM is shown below in the Figure 1 .
Figure 1. EVM Block Diagram
DAC7741EVM 4 SLAU093A – October 2002 – Revised May 2005

www.ti.com
7 Physical Description
7.1 PCB Layout
+15V-15V
Physical Description
This section describes the physical characteristics and PCB layout of the EVM and lists the componentsused on the module.
The EVM is constructed on a four-layer printed-circuit board using a copper-clad FR-4 laminate material.The printed-circuit board has a dimension of 96,52 mm (3.80 inch) X 102,87 mm (4.050 inch), and theboard thickness is 1,57 mm (0.062 inch). Figure 2 through Figure 6 show the individual artwork layers.
Figure 2. Top Silkscreen
DAC7741EVMSLAU093A – October 2002 – Revised May 2005 5

www.ti.com
Physical Description
Figure 3. Layer One (Top Signal Plane)
DAC7741EVM 6 SLAU093A – October 2002 – Revised May 2005

www.ti.com
Physical Description
Figure 4. Layer Two (Split Ground Plane)
DAC7741EVMSLAU093A – October 2002 – Revised May 2005 7

www.ti.com
Physical Description
Figure 5. Layer Three (Split Power Plane)
DAC7741EVM 8 SLAU093A – October 2002 – Revised May 2005

www.ti.com
Physical Description
Figure 6. Layer Four (Bottom Signal Plane)
DAC7741EVMSLAU093A – October 2002 – Revised May 2005 9

www.ti.com
Physical Description
Figure 7. Bottom Silkscreen
DAC7741EVM 10 SLAU093A – October 2002 – Revised May 2005

www.ti.com
Physical Description
Figure 8. Drill Drawing
DAC7741EVMSLAU093A – October 2002 – Revised May 2005 11

www.ti.com
8 Bill Of Materials
Bill Of Materials
Table 1. Parts ListItem Quantity Designators Manufacturer Part Number Description
1 2 R8, R15 Panasonic ERJ-8GEY0R00V 0 Ohm
2 1 C8 TDK C3216C0G1H105JT 1 µF
C1, C2, C3, C7, C13
(1)
, C15,3 14 C16, C17, C18, C19, C20, TDK C3216C0G1E104JT 0.1 µF
(1)
C21, C22, C23
4 2 C9, C10 TDK C3216X7RJ103KT 0.01 µF
5 1 C12 TDK C3216C0G2J102JT 1 nF
W6, W7, W8, W9, W10,6 11 W11, W16, W17, W20, W21, Molex 22-03-2021 2 CIRCUIT HEADER, .100 STRAIGHTW22
W1, W2, W3, W4, W5, W12,W18, W19, W23, W24, W25,7 17 Molex 22-03-2031 3 CIRCUIT HEADER, .100 STRAIGHTW26, W27, W28, W29, W30,W31
8 1 P6 Samtec SSW-105-22-F-D-VS-K 10-PIN Isolated Power Socket, .100
(2)
R4, R5, R6, R12, R13, R14, 10-K Ohms 1206 1/4W 5% Chip9 9 Panasonic ERJ-8ENF1002VR16 R17, R18 Resistor
10 2 R1, R2 Bourns 3214W-103E 10-K potentiometer
11 1 R10 Panasonic ERJ-8ENF2002V 20K Ohms 1206 1/4W 5% Chip Res.
12 1 R11 Bourns 3214W-104E 100-K potentiometer
13 1 R9 Bourns 3214W-203E 20-K potentiometer
14 5 C4, C5, C6, C11, C14
(1)
TDK C3225X5R1C106KT 10 µF
(1)
15 3 J2, J3, J4 Samtec TSM-110-01-S-DV-M 20-PIN IDC
16 1 J6 Samtec TSM-105-01-T-DV 10-PIN IDC
17 3 P2, P3, P4 Samtec SSW-110-22-S-D-VS-P 20-PIN IDC
(2)
18 2 J11, J12 On-Shore Tech. ED555/3DS 3-Pin Terminal Connector
19 1 J1 Samtec TSM-116-01-S-DV-M 32-PIN IDC
20 1 P1 Samtec SSW-116-22-S-D-VS-P 32-PIN IDC
(2)
21 1 U1 TI DAC7741 DAC7741
22 1 U2 TI OPA227UA 8-SOP (D)
23 1 U3 TI REF102AU 8-SOP (D)
24 1 U4 TI OPA2277UA 8-SOP (D)
25 1 U5 TI SN74AHC541PW 20-Pin TSSOP 9PW)
26 1 U6 TI SN74ALVC164245DL 48-SSOP (DL)
27 1 U7 TI SN74AHC1G08DBVR 5-SOT (DBV)
28 1 U8 TI SN74AHC1G04DBVR 5-SOT (DBV)
29 1 U9 TI SN74AUP1G57DBVR SOT23-6 (DBV)
30 1 U10 TI SN74AHC138D 16-SOP (D)
31 2 TP1, TP2 Mill-Max 2348-2-01-00-00-07-0 TP_TURRENT
(1)
C13 and C14 are not populated. Use only when an external reference source is derived from TP1, J2-20, or J4-20 (particularlywith an unclean source).(2)
P1, P2, P3, P4, and P6 parts are not shown in the schematic diagram. All the P-designated parts are installed in the bottomside of the PC board opposite the J-designated counterpart. Example, J1 is installed on the top side while P1 is installed in thebottom side opposite of J1.
DAC7741EVM 12 SLAU093A – October 2002 – Revised May 2005

www.ti.com
9 EVM Operation
9.1 Factory Default Settings
EVM Operation
This section covers in detail the operation of the EVM to provide guidance to the user in evaluating theonboard DAC, and how to interface the EVM to a specific host processor.
See the DAC7741 data sheet, SBAS248 , for information about its parallel interface and other relatedtopics.
The EVM board is factory tested and configured to operate in the bipolar output mode.
The EVM board is set to its default configuration from factory as described on the table below to operatein bipolar ±10-V mode of operation using the external reference.
Table 2. Factory Default Jumper Settings
Reference Jumper Position Function
W1 OPEN V
REF
output pin is floated and not used for offset adjustment.W2 OPEN REFEN pin is not used to enable 10-V internal reference.W3 2-3 External reference source, U3, is routed to REF
IN
to provide 10-V reference.W4 1-2 Onboard external reference through U3 is connected.W5 1-2 Negative supply rail of the U2 operational amplifier is supplied with -15 V.W6 OPEN REFADJ pin is floated.W7 CLOSE RFB2 pin is strapped to V
OUT
pin for DAC output feedback.W8 CLOSE TEST pin is tied to DGND.W9 OPEN SJ pin is floated.W10 OPEN RFB1 is floated.W11 CLOSE AGND and DGND are tied together to a common point.W12 2-3 The LDAC signal used is address decoded, and translated to the DSP_LDAC.W13 3-4 Buffered output of DAC is fed through W30 and to J4 terminal.External reference is disconnected from the negative input of U2 to configure U2 forW14 OPEN
unity gain.W15 OPEN Configure U2 operational amplifier for unity gain.W16 OPEN RSTSEL pin is tied high to set DAC reset value to mid-scale.W17 OPEN RST pin is tied high by default.W18 1-2 U6 direction control, DIR, set to A-to-B direction.W19 OPEN RST pin not driven.W20 CLOSED The U5 output enable pins, OE1 and OE2, are enabled.W21 OPEN The U6 enable pins, 1G and 2G, are enabled.W22 OPEN The U6 direction pin, DIR, is not controlled by the R/ W signal.W23 2-3 The U6 is powered with 3.3 VD.W24 2-3 The DC_CSa# signal is used to control the R/ W function.W25 1-2 The DSP_R/ W pin is used to control the CS function.W26 1-2 The C6x_RD pin is routed for the combination DSP_R/ W control signal.W27 1-2 The C6x_ WR pin is routed for the combination DSP_R/ W control signal.W28 OPEN The DSP_ CS pin is not used (C5x™ DSP only).W29 1-2 The DC_CSa# is used to control the enable function of U10.W30 1-2 V
OUT
is routed to J4 terminal.W31 OPEN External reference source via pin 20 of J2 or J4 is not used.
DAC7741EVMSLAU093A – October 2002 – Revised May 2005 13

www.ti.com
9.2 Host Processor Operations
EVM Operation
The host processor basically drives the DAC; so, the DAC proper operation depends on the successfulconfiguration between the host processor and the EVM board. In addition, a properly written code is alsorequired to operate the DAC.
A custom cable can be made specific to the host interface platform. The EVM allows interfacing to thehost processor through J3 header connector for the control signals, and J1 header connector for the datainput. An interface adapter card for a specific DSP starter kits or an HPA449 platform is also available asmentioned in section 1 of this manual.
The EVM includes an optional signal conditioning circuit for the DAC output through an externaloperational amplifier, U2. This is set to a unity gain configuration by default. Regardless, the raw output ofthe DAC can be probed through W13 pin 2 so that it can be compared with the output of U2, if necessary.The output terminals J2 and J4 are provided to monitor the desired output of the DAC by shorting therespective pins of W13 and selecting the position of W30.
The following sections describe the different configurations of the output amplifier, U2.
9.2.1 Unity Gain Output
The buffered output configuration is used to prevent loading the DAC7741 and should closely match theraw output of the DAC with maybe some slight distortion because of the feedback resistor and capacitor.The user can tailor the feedback circuit to closely match the desired wave shape by simply desoldering R6and C12 and replacing them with the desired values. If desired, the user can simply delete R6 and C12altogether, and solder a 0- Ωresistor in place of R6.
Table 3 shows the jumper setting for the unity gain configuration of the DAC external output buffer inunipolar or bipolar mode.
Table 3. Unity Gain Output Jumper Settings
Jumper SettingReference FunctionUnipoar Bipolar
W5 2-3 1-2 Supplies the voltage for the negative rail of the operational amplifier.W13 3-4 3-4 DAC output is sent to the output terminals.W14 Open Open exREFin is disconnected from the negative input of the operational amplifier.W15 Open Open Disconnect negative input of the operational amplifier from GND
DAC7741EVM 14 SLAU093A – October 2002 – Revised May 2005

www.ti.com
EVM Operation
9.2.2 Output Gain of Two
This configuration allows the DAC output with a gain of two but is limited to the effective rails of theoperational amplifier. When the DAC7741 is configured to operate in bipolar mode, the DAC output mustbe within the range of 12 V
PP
or less. Anywhere above the range of 12 V
PP
clips the output of theoperational amplifier. Likewise, when operating the DAC in unipolar mode, the DAC output must notexceed 6 V
PP
.
Table 4 shows the proper jumper settings of the EVM for the 2x gain output of the DAC.
Table 4. Gain of Two Output Jumper Settings
Reference Jumper Setting Function
1-2 (Bipolar) Negative rail of the operational amplifier tied to -15 V for bipolar operation orW5
2-3 (Unipolar) AGND for unipolar operation.W13 3-4 Amplified output of DAC is sent to the output terminal.W14 Open Disconnect exREFin from negative input of the operational amplifier.W15 Open Configures the operational amplifier for a 2x gain output.
9.2.3 Capacitive Load Drive
Another output configuration option is to drive a wide range of capacitive load requirement. However, alloperational amplifiers under certain conditions may become unstable depending on the operationalamplifier configuration, gain, and load value. These are just few factors that can affect operationalamplifiers stability performance and should be considered when implementing.
In unity gain, the OPA627 operational amplifier, U2, performs well with large capacitive loads. Increasingthe gain enhances the amplifier’s ability to drive even more capacitance, and by adding a load resistorwould even improve the capacitive load drive capability.
Table 5 shows the jumper setting configuration for a capacitive load drive.
Table 5. Capacitive Load Drive Output Jumper Settings
Reference Jumper Setting Function
1-2 (Bipolar) Negative rail of the operational amplifier tied to -15 V for bipolar operation or AGND forW5
2-3 (Unipolar) unipolar operation.W13 3-4 Capacitive load drive output of DAC is channeled to the output terminalsW14 Open Disconnect exREFin from negative input of the operational amplifier.W15 Open Disconnect R12
(1)
(1)
If there is a need to incrementally adjust the capacitive load output, replace R12 with a capacitor with the desired capacitancevalue and close W15.
DAC7741EVMSLAU093A – October 2002 – Revised May 2005 15

www.ti.com
9.3 Jumper Setting
13
13
13
13
13
13
13
13
13
13
13
EVM Operation
The figures in Table 6 shows the function of each jumper on the EVM.
Table 6. Jumper Setting Function
Reference Jumper Setting Function
R
OFFSET
is strapped to V
REF
to set V
(SJ)
(summing junction) to V
REF
/2. See the data sheetfor offset adjustment.
R
OFFSET
is not connected to set V
(SJ)
(summing junction) to V
REF
/3. See the data sheet forW1
offset adjustment.
R
OFFSET
is strapped to AGND to set V
(SJ)
(summing junction) to V
REF
/6. See the data sheetfor offset adjustment.
Disables the internal reference voltage.
W2
Enables the internal reference voltage of 10 V.
REF
IN
is strapped to REF
OUT
to allow the internal 10 V to supply the DAC referencevoltage.W3
REF
IN
is strapped to exREFin to allow either the onboard adjustable reference oruser-supplied reference to supply the DAC reference voltage.
Routes the onboard 10-V reference through the adjustable potentiometer to W3 and W14.
W4
Routes the user-supplied reference from TP1 or J4-20 through the adjustable poten-tiometer to W3 and W14.
Negative supply rail of operational amplifier is powered by -15 V.
W5
Negative supply rail of operational amplifier is tied to AGND.
REFADJ pin is not connected.W6
REFADJ pin is connected to R1 potentiometer for gain adjustment input when internalreference is used.
RFB2 pin is not connected to the V
OUT
pin.W7
RFB2 pin is strapped to the V
OUT
pin for feedback.
TEST pin not connected to DGND.W8
TEST pin connected to DGND (default mode).
SJ (summing junction) pin of the DAC output amplifier is not connected.W9
SJ (summing junction) pin of the DAC output amplifier is connected to R2 potentiometer toallow small amount of current for offset adjustment.
RFB1 pin is not connected.W10
RFB1 pin is strapped to RFB2 pin for DAC V
OUT
feedback.
Disconnects AGND from DGND.W11
Connects AGND and DGND together.
DAC7741EVM 16 SLAU093A – October 2002 – Revised May 2005

www.ti.com
13
13
2
1
6
5
4
3
2
1
6
5
4
3
2
1
6
5
4
3
13
13
13
13
EVM Operation
Table 6. Jumper Setting Function (continued)
Reference Jumper Setting Function
Positive supply rail of operational amplifier is powered by 15 V.
W12
Positive supply rail of operational amplifier is powered by V
CC
.
Routes the raw output of the DAC7741 to J4-2 and J5 output terminals.
Routes the output of U2 to J4-2 and J5 output terminals. Used for unipolar and bipolarW13
modes of operation.
Routes the output of U2 to J4-2 and J5 output terminals. Used for capacitive load driving.
Disconnects exREFin from the negative input terminal of U2.W14
Allows exREFin to be routed to the negative input terminal of U2 used for experimentationpurposes only.
Disconnects the negative terminal of U2 to AGND and disables 2x gain.W15
Configures U2 for a 2x gain output.
RSTSEL pin is pulled high and configures the DAC to mid-scale when POR or reset isinitiated.W16
RSTSEL pin is pulled low and configures the DAC to min-scale when POR or reset isinitiated.
RST pin is pulled high and configures the DAC not to reset (default state).W17
RST pin is pulled low and holds the DAC to reset state.
The U6 DIR control pin is tied high for direction flow from A-to-B.
W18
The U6 DIR control pin is tied low for direction flow from B-to-A.
The HPA449_ RST pin (via J3-13) is used to drive the RST signal.
W19
The DSP_ RST pin (via U10-11) is used to drive the RST signal.
U5 is disabled.W20
U5 is enabled.
U6 is disabled.W21
U6 is enabled.
R/ W is not routed through to control U6 direction pin, DIR.W22
R/ W is routed through to control U6 direction pin, DIR.
DAC7741EVMSLAU093A – October 2002 – Revised May 2005 17

www.ti.com
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
9.4 Schematic
EVM Operation
Table 6. Jumper Setting Function (continued)
Reference Jumper Setting Function
U6 is powered with 5 VD.
W23
U6 is powered with 3.3 VD.
The WR signal (via J3-3) controls the R/ W function.
W24
The DC_CSa# signal (via J3-1) controls the R/ W function.
The DSP_R/ W signal (if using C6x™ DSP) is used to control the CS function.
W25
The DSP_ CS signal (if using C5x™ DSP) or the HPA449_ CS signal (if using HPA449) isused to control the CS function. Works with W28.
The C6x_RD signal is routed for the combination DSP_R/ W signal function.
W26
The RD signal (if using C5x™ DSP) is routed for the combination DSP_R/ W signalfunction.
The C6x_ WR signal is routed for the combination DSP_R/ W signal function.
W27
WR signal (if using C5x™ DSP) is routed for the combination DSP_R/ W signal function.
The combination CE signal (if using C5x™ DSP) is used to generate the DSP_ CS signal.
W28
The DC_CSa# signal (if using C5x™ DSP) or HPA449_ CS signal (if using HPA449) isused to control the CS function. Works with W25.
The DC_CSa# signal is used to control the enable pins of U6.
W29
The enable pin of U6 is tied low, which enables the device all the time.
DAC V
OUT
is routed to J4 terminal.
W30
DAC V
OUT
is routed to J2 terminal.
External reference source through J4-20 is routed in.
W31
External reference source through J2-20 is routed in.
Legend: Indicates the corresponding pins that are shorted or closed.
A schematic of the DAC7741 is found on the following page.
DAC7741EVM 18 SLAU093A – October 2002 – Revised May 2005

A
B
C
D
D
C
B
Ati
12500 TI Boulevard. Dallas, Texas 75243
Title:
SHEET: OF:
FILE: SIZE:
DATE:
REV:
10-May-2005
Drawn By:
Engineer:
Revision History
REV ECN Number Approved
DAC7741_Sheet1.Sch
DOCUMENTCONTROL #
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
VSS VCC +3.3VD
-5VAVCC +3.3VA +5VD
W11
12 34 56 78 910 1112 1314 1516 1718 1920
J4
RSTSEL
HPA449_RST
LDAC
WR
DC_CSa#
1 2
3 4
5 6
7 8
910
J6 1 2
3 4
5 6
7 8
910
11 12
13 14
15 16
17 18
19 20
J3
12 34 56 78 910 1112 1314 1516 1718 1920 2122 2324 2526 2728 2930 3132
J1
CONNECTORS AND LOGIC
C
1
J. PARGUIAN
VSS
+5VD
+REFin
REFen
2
R13
10k R14
10k
+5VD
W16 W17
6443168
+5VA+1.8VD+3.3VD
1 2 3
J11
1 2 3
J12
5
67
U4B
OPA2227UA
OE1 1
A1 2
A2 3
A3 4
A4 5
A5 6
A6 7
A7 8
A8 9
GND 10 Y8
11 Y7
12 Y6
13 Y5
14 Y4
15 Y3
16 Y2
17 Y1
18 OE2
19 VCC
20
U5
SN74AHC541
C16
0.1µF
C17
0.1µF
C20
0.1µF C21 0.1µF
C19
0.1µF
R17
10K
R16
10K
W20
W21
+5VD
W19
W12
DSP_LDAC
RD
DSP_RST
LDAC_B
R/W_B
RST_B
RSTSEL_B
REFen_B
RST
RSTSEL
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
DB8
DB9
DB10
DB11
DB12
DB13
DB14
DB15
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
W18
+5VD
+5VD
+5VD
+5VD
+3.3VD
+5VD
1DIR
11B1
21B2
3GND
41B3
51B4
6VCC
71B5
81B6
9GND
10 1B7
11 1B8
12 2B1
13 2B2
14 GND
15 2B3
16 2B4
17 VCC
18 2B5
19 2B6
20 GND
21 2B7
22 2B8
23 2DIR
24 2G 25
2A8 26
2A7 27
GND 28
2A6 29
2A5 30
VCC 31
2A4 32
2A3 33
GND 34
2A2 35
2A1 36
1A8 37
1A7 38
GND 39
1A6 40
1A5 41
VCC 42
1A4 43
1A3 44
GND 45
1A2 46
1A1 47
1G 48
U6
SN74ALVC164245
R18
10K
R/W_B
DIR
DIR
EN
EN
W22
DIR
W23
VCCA
VCCA
RD
2 4
53
U8
SN74AHC1G04
53
U7
SN74AHC1G08
DSP_R/W
A0
A1
A2
A
1B
2C
3
G1
6G2A
4G2B
5
Y0 15
Y1 14
Y2 13
Y3 12
Y4 11
Y5 10
Y6 9
Y7 7
VCC 16
GND
8
U10
SN74AHC138
+3.3VD
A0
A1
A2
+3.3VD
C18
0.1µF
W26
W27
W28
W24
W25
C6x_RD
C6x_WR
CE
DC_CSa#
DSP_CS
WR
DSP_R/W
DSP_LDAC
DSP_RST
CS
R/W
DC_CSa#
RST
+3.3VD
C22
0.1µF
W29
DC_CSa#
In1 1
GND 2
In0 3 Y
4VCC
5In2
6U9
SN74AUP1G57
+3.3VD
C23
0.1µF
DSP_CS
(HPA449_R/W)
(HPA449_LDAC)
(HPA449_CS)
HPA449_RST
RSTSEL
REFen
+5VD
R4
10K
[DB15..DB0]
Control_Signals
[DB15..DB0]
OUTPUT
DAC7741
DAC7741_Sheet2.Sch
[DB15..DB0]
Control_Signals
Control_Signals
CS_B
U2_VOUT W30
W31
12 34 56 78 910 1112 1314 1516
20 17 19
18
J2
(HPA449_LDAC)
(HPA449_R/W)
(HPA449_CS)
A Original Release
B Added Logic to accomodate 5-6K card
CAdded option of selecting output
terminal and corrected DSP CS &
R/nW logic.
(HPA449_CS)

A
B
C
D
D
C
B
Ati
12500 TI Boulevard. Dallas, Texas 75243
Title:
SHEET: OF:
FILE: SIZE:
DATE:
REV:
10-May-2005
Drawn By:
Engineer:
Revision History
REV ECN Number Approved
DAC7741_Sheet2.Sch
DOCUMENTCONTROL #
DAC7741
C
2
J. PARGUIAN
2
6443168
C1
0.1µF
C7
0.1µF
C2
0.1µF
VCC
R6
10K
R5
10K
VSS
2
3
6
4
71
5
U2
Op Amp
VCC
C10
0.01µF
C9
0.01µF
R12
10K
W15
W14
C12
1nF
1
23
45
6
A
B
C
W13
CLD_OUT
W5
R8
0
GND
4
TRIM
5
NC 1
NC
7NC
8TEMP 3
OUT 6
V+
2
U3
REF102AU(8)
C11
10µF
C3
0.1µF
VCC
1
3
TP1
TP2
EXTERNAL
REFERENCE
1
2
3
R11
100K
R10
20K
(exREFin)
1
2
3
R9
20K
+5VD
W4
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
DB8
DB9
DB10
DB11
DB12
DB13
DB14
DB15
C6
10µF
C4
10µF
C5
10µF
DB0
16 DB1
17 DB2
18 DB3
19 DB4
20 DB5
21 DB6
22 DB7
27 DB8
28 DB9
29 DB10
30 DB11
31 DB12
32 DB13
33 DB14
34 DB15
35
VDD
38
REFin 47
REFout 45
Vref 4
DGND
37
CS 41
R/W 42
LDAC 40
RST 39
RSTSEL 43
REFEN 44
REFadj 46
Roffset 5
AGND 6
AGND 7
RFB2
8
RFB1
9SJ
10
Vout 11
TEST
26
VCC 3
VSS 2
U1
DAC7741
W2
W1
VSS
W7
W10
R3
100K
C8
1µF
R1
10K
R2
10K
R7
0/5K/20K
W3
W8
W6
W9
Tantalum
C13
0.1µF
C14
10µF
2
31
84
U4A
OPA2227UA
R15
0
VCC
C15
0.1µF
REFen_B
[DB15..DB0]
OUTPUT
Control_Signals
DAC_VOUT
DAC_VOUT
Sum_Junc
Sum_Junc
exREFin
exREFin
DAC_VOUT
LDAC_B
R/W_B
RST_B
RSTSEL_B
CS_B
+REFin
U2_VOUT
+REFin