Texas Instruments THS6222RHFEVM User manual

1
SBOU229–August 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
THS6222RHF Evaluation Module
User's Guide
SBOU229–August 2019
THS6222RHF Evaluation Module
This user's guide describes the characteristics, operation, and use of the THS6222RHFEVM. This
evaluation module (EVM) is an evaluation and development kit for evaluating the THS6222IRHF, a
differential line-driver amplifier with a current-feedback architecture that is targeted for use in broadband
power line communications (PLC) line driver applications. A complete circuit description as well as
schematic diagram and bill of materials are included in this document.
Throughout this document, the abbreviation EVM and the term evaluation module are synonymous with
the THS6222RHFEVM.
The following related documentation is available through the Texas Instruments web site at www.ti.com.
Related Documentation
Device Literature Number
THS6222 data sheet SBOS974
Contents
1 Introduction ................................................................................................................... 2
2 Power Connections.......................................................................................................... 2
3 Input and Output Connections ............................................................................................. 3
4 Board Layout ................................................................................................................. 4
5 Schematic and Bill of Materials ............................................................................................ 5
List of Figures
1 Top Layer..................................................................................................................... 4
2 Ground Layer................................................................................................................. 4
3 Power Layer.................................................................................................................. 4
4 Bottom Layer................................................................................................................. 4
5 THS6222RHFEVM Schematic............................................................................................. 5

Introduction www.ti.com
2SBOU229–August 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
THS6222RHF Evaluation Module
List of Tables
1 THS6222RHFEVM Specifications......................................................................................... 2
2 Bill of Materials............................................................................................................... 6
Trademarks
All trademarks are the property of their respective owners.
1 Introduction
The THS6222RHFEVM is an evaluation module for the single THS6222 amplifier in the RHF package.
This evaluation module is designed to quickly and easily demonstrate the functionality and versatility of
the amplifier. The EVM is ready to connect to power, signal sources, and test instruments through the use
of onboard connectors. The EVM comes configured for easy connection with common 50-Ωlaboratory
equipment on its inputs and outputs. The amplifier is configured for a differential input with a gain of 10
V/V to a differential output. The board includes jumpers to easily switch the device between different bias
modes and a potentiometer to set the value of the IADJ pin. The EVM can be easily configured for other
gains and for single- or split-supply operation. The output transformer and resistors are configured to
present a 50-Ω, single-ended output.
1.1 Features
• Configured for split-supply operation and easily modified for single supply
• Default gain of 10-V/V configuration can easily be reconfigured for other gains
• Designed for easy connection to standard 50-Ωinput/output impedance test equipment
• Inputs and outputs include subminiature version A (SMA) connectors
1.2 EVM Specifications
Table 1 lists the typical performance specifications for the THS6222RHFEVM.
Table 1. THS6222RHFEVM Specifications
Specification Typical Value Range
Split-supply voltage range ±4 V to ±26 V
Single-supply voltage range (VEE = ground) 8 V to 32 V
Quiescent current (no load, split supply, full-bias mode) 20.5 mA
Output voltage swing (VCC = 12 V, 100-Ωload) 19.6 VPP
Linear output current (VCC = 12 V, 25-Ωload) 355 mA
2 Power Connections
The THS6222RHFEVM is equipped with a wire socket for easy connection of power. The positive supply
input is labeled V+, the negative supply input is labeled V–, and ground (GND) is the unlabeled center
terminal of the power-supply connector.
2.1 Split-Supply Operation
To operate as a split supply, apply the positive supply voltage to V+, the negative supply voltage to V–,
and the ground reference from supply to GND.
2.2 Single-Supply Operation
To operate as a single supply, connect both the V– connector and the GND connector to ground and
apply the positive supply voltage to V+.

www.ti.com Input and Output Connections
3
SBOU229–August 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
THS6222RHF Evaluation Module
3 Input and Output Connections
The THS6222RHFEVM is equipped with SMA connectors for easy connection of signal generators and
analysis equipment. As shipped, the EVM is configured for a gain of 10-V/V, split-supply, differential input
and output with 50-Ωtermination. By default, the inputs INA and INB are configured for a differential input
connection. To use the device with a single-ended input, either use an external transformer or populate
transformer T1 on the board, remove R21, populate R15 with a 0-Ωresistor, and use INA as the single-
ended input. OUTA (J5) is the output connector for single-ended output signals. The output resistors R10
and R11 in combination with the transformer (T2) on the amplifier output provide a 25-Ωload to the
amplifier when terminated in 50 Ωdifferentially. To use the EVM with a single-ended output, remove
resistor R23 and populate resistor R18 with 0 Ω, which gives a single-ended output on OUTA. The EVM
contains provisions for additional output devices to change the loading of the amplifier and to add
protection devices. See the THS6222 data sheet applications section, schematics, and layouts for more
detail and how to reconfigure the EVM.
3.1 Bias Mode Control Pins
The amplifier bias modes can be controlled through shorting jumpers J1 and J2. By default, the jumper
shorts are left unconnected, which pulls the input signals low, leaving the device in its full-bias mode.
Jumper J1 controls pin BIAS-1 and jumper J2 controls pin BIAS-2. In conjunction the jumpers can be used
to place the device in its three bias modes or in shutdown.
3.2 IREF Pin Connection
The fine current adjustment (IADJ) pin of the device is controlled using the potentiometer R17 on the
board. By default the potentiometer is set to 0 Ω, which yields the maximum quiescent current for each
bias mode. By increasing the resistance of the potentiometer, the quiescent current can be reduced to a
desired lowered value at the cost of reduced performance.
3.3 Optional VCM Pin Connection
The EVM includes an optional connection on the VCM (pin 5) of the device for a capacitor. The optional
VCM capacitor can be added to help filter common-mode noise if needed by the application. VCM is not
populated by default on the EVM.

Board Layout www.ti.com
4SBOU229–August 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
THS6222RHF Evaluation Module
4 Board Layout
The layer plots of Figure 1 to Figure 4 illustrate the board layers in top to bottom order.
Figure 1. Top Layer Figure 2. Ground Layer
Figure 3. Power Layer Figure 4. Bottom Layer

1
1
2
2
3
3
4
4
5
5
6
6
D D
C C
B B
A A
1 2
7/30/2019
AMPS083E1.SchDoc
Sheet Title:
Size:
Mod. Date:
File:
Sheet: of
B http://www.ti.com
Contact: http://www.ti.com/support
THS6222RHFEVMProject Title:
Designed for: Public Release
Assembly Variant: 001
©Texas Instruments 2018
Drawn By:
Engineer: Jacob Freet
Texas Instruments and/or its licensors do not warrant the accuracy or completeness of this specification or any information contained therein. Texas Instruments and/or its licensors do not
warrant that this design will meet the specifications, will be suitable for your application or fit for any particular purpose, or will operate in an implementation. Texas Instruments and/or its
licensors do not warrant that the design is production worthy. You should completely validate and test your design implementation to confirm the system functionality for your application.
Not in version controlSVN Rev:
AMPS083Number: Rev: E1
TID #: N/A
Orderable: THS6222RHFEVM
Iadj
GND
GND
VCC
VCC
GND
GND
VCC
VEE
GND
GND
GND
1
2
3
J7
90 ohm
L1
90 ohm
L2
VEE
VCC
1nF
100V
C3
2.2µF
50V
C1
2.2µF
50V
C2
10nF
50V
C4
1
2
3 4 5
J3
IN A
1
2
3 4 5
J4
IN B
0
R15
1
2
34
5
6
T1
TT1-6-KK81+
TP1
24.9
R1
24.9
R2 0
R16
1.24k
R8
1.24k
R7
274
R9
10k
R3
10k
R4
10k
R5
10k
R6
24.9
R10
24.9
R11
49.9
R12
49.9
R13
1
2
34
5
6
T2
TT1-6-KK81+
0R14
GND
0
R18
1
2
3 4 5
J5
OUT A
1
2
3 4 5
J6
OUT B
GND
0
R19
GND
0
R20
100nF
25V
C5 100nF
25V
C6
GNDGND
100nF
25V
C7 100nF
25V
C8
GND
100nF
25V
C9
100nF
25V
C10
GND
GND
0R22
0R21
GND
GND
0R23
100nF
25V
C12
100nF
25V
C11
TP2
OUT A
TP3
OUT B
TP4
GND
GND
TP5
GND
GND
Typical Power Supply Current Reading for Different Bias Modes
Bias Mode J1 position J2 position IQ(typ)
Full Open 21 mA
Mid Closed Open 16 mA
Low Open Closed 11 mA
Shut-down Closed Closed < 1mA
Open
CW
CCW
1
3
2
D1
MMBZ27VCL-7-F
100nF
25V
C13
GND
1
3
2
D2
BAT54S-7-F
1
3
2
D3
VCC VCC
GND
0R27
0
R28
0R26
100nF
25V
C14
0
R25
0
R24
VEE VEE
31
2
10k ohm
R17
3223W-1-103E
1
2
J2
B2_AB
1
2
J1
B1_AB
D1 IN+
1
D1 FB
19
D2 IN+
2
D2 FB
18
BIAS-1/D1D2
23
BIAS-2/D1D2
24
NC
6
NC 14
NC
7
NC 13
NC
9
NC
8
IADJ
4
NC 11
VS+
21 D1 OUT 20
D2 OUT 17
NC 15
NC 12
VCM
5
NC 16
PAD 25
NC 10
VS- 22
GND 3
THS6222IRHF
U1
www.ti.com Schematic and Bill of Materials
5
SBOU229–August 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
THS6222RHF Evaluation Module
5 Schematic and Bill of Materials
This section provides the schematic and bill of materials (BOM) for the THS6222RHFEVM.
5.1 Schematic
Figure 5 shows the EVM schematic.
Figure 5. THS6222RHFEVM Schematic

Schematic and Bill of Materials www.ti.com
6SBOU229–August 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
THS6222RHF Evaluation Module
5.2 Bill of Materials
Table 2 lists the EVM BOM.
Table 2. Bill of Materials
Designator Qty Value Description Package Reference Part Number Manufacturer
C1, C2 2 2.2uF CAP, CERM, 2.2 uF, 50 V, +/- 10%, X7R, 0805 805 C2012X7R1H225K125AC TDK
C3 1 1000pF CAP, CERM, 1000 pF, 100 V, +/- 20%, X7R, 0603 603 CX0603MRX7R0BB102 Yageo America
C4 1 0.01uF CAP, CERM, 0.01 uF, 50 V, +/- 10%, X7R, 0805 805 08055C103KAT2A AVX
C9, C10 2 0.1uF CAP, CERM, 0.1 uF, 25 V, +/- 5%, X7R, 0603 603 C0603C104J3RACTU Kemet
H1, H2, H3, H4 4 Machine Screw, Round, #4-40 x 1/4, Nylon, Philips panhead Screw NY PMS 440 0025 PH B&F Fastener
Supply
H5, H6, H7, H8 4 Standoff, Hex, 0.5"L #4-40 Nylon Standoff 1902C Keystone
J1, J2 2 Header, 100mil, 2x1, Gold, TH Sullins 100mil, 1x2, 230
mil above insulator PBC02SAAN Sullins Connector Solutions
J3, J4, J5, J6 4 Connector, End launch SMA, 50 ohm, SMT SMA End Launch 142-0701-851 Cinch Connectivity
J7 1 Terminal Block, 5.08 mm, 3x1, Brass, TH 3x1 5.08 mm Terminal
Block ED120/3DS On-Shore Technology
L1, L2 2 90 ohm Ferrite Bead, 90 ohm @ 100 MHz, 1.5 A, 1206 1206 MI1206K900R-10 Laird-Signal
Integrity Products
LBL1 1 Thermal Transfer Printable Labels, 0.650" W x 0.200" H - 10,000
per roll PCB Label 0.650 x 0.200 inch THT-14-423-10 Brady
R1, R2 2 24.9 RES, 24.9, 1%, 0.1 W, AEC-Q200 Grade 0, 0402 402 ERJ-2RKF24R9X Panasonic
R3, R4, R5, R6 4 10k RES, 10 k, 5%, 0.1 W, 0603 603 RC1608J103CS Samsung Electro-
Mechanics
R7, R8 2 1.24k RES, 1.24 k, 1%, 0.063 W, AEC-Q200 Grade 0, 0402 402 CRCW04021K24FKED Vishay-Dale
R9 1 274 RES, 274, 1%, 0.063 W, AEC-Q200 Grade 0, 0402 402 CRCW0402274RFKED Vishay-Dale
R10, R11 2 24.9 RES, 24.9, 1%, 0.1 W, 0603 603 RC0603FR-0724R9L Yageo
R14, R23, R26, R27 4 0 RES, 0, 5%, 0.1 W, 0603 603 RC0603JR-070RL Yageo
R16, R21, R22 3 0 RES, 0, 5%, 0.063 W, 0402 402 RC0402JR-070RL Yageo America
R17 1 10k
ohm TRIMMER 10k OHM 0.125W SMD 3.52x4.16x3.94mm 3223W-1-103E Bourns
T2 1 RF Transformer, 50ohm, 0.004 to 300 MHz, SMT 7.62x6.86mm TT1-6-KK81+ Minicircuits
TP1 1 Test Point, Miniature, Red, TH Red Miniature Testpoint 5000 Keystone
TP4, TP5 2 Test Point, Miniature, Black, TH Black Miniature Testpoint 5001 Keystone
U1 1 THS6222IRHF, RHF0024A (VQFN-24) RHF0024A THS6222IRHF Texas Instruments
C5, C6, C7, C8, C11,
C12, C13, C14 0 0.1uF CAP, CERM, 0.1 uF, 25 V, +/- 5%, X7R, 0603 603 C0603C104J3RACTU Kemet
D1 0 27V Diode, TVS, Uni, 27 V, 38 Vc, SOT-23 SOT-23 MMBZ27VCL-7-F Diodes Inc.

www.ti.com Schematic and Bill of Materials
7
SBOU229–August 2019
Submit Documentation Feedback Copyright © 2019, Texas Instruments Incorporated
THS6222RHF Evaluation Module
Table 2. Bill of Materials (continued)
Designator Qty Value Description Package Reference Part Number Manufacturer
D2, D3 0 30V Diode, Schottky, 30 V, 0.2 A, SOT-23 SOT-23 BAT54S-7-F Diodes Inc.
R12, R13 0 49.9 RES, 49.9, 1%, 0.063 W, AEC-Q200 Grade 0, 0402 402 CRCW040249R9FKED Vishay-Dale
R15, R19 0 0 RES, 0, 5%, 0.063 W, 0402 402 RC0402JR-070RL Yageo America
R18, R20, R24, R25,
R28 0 0 RES, 0, 5%, 0.1 W, 0603 603 RC0603JR-070RL Yageo
T1 0 RF Transformer, 50ohm, 0.004 to 300 MHz, SMT 7.62x6.86mm TT1-6-KK81+ Minicircuits
TP2, TP3 0 Test Point, Miniature, Red, TH Red Miniature Testpoint 5000 Keystone

STANDARD TERMS FOR EVALUATION MODULES
1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or
documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance
with the terms set forth herein. User's acceptance of the EVM is expressly subject to the following terms.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms do not apply to Software. The warranty, if any, for Software is covered in the applicable Software License
Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for a nonconforming EVM if (a) the nonconformity was caused by
neglect, misuse or mistreatment by an entity other than TI, including improper installation or testing, or for any EVMs that have
been altered or modified in any way by an entity other than TI, (b) the nonconformity resulted from User's design, specifications
or instructions for such EVMs or improper system design, or (c) User has not paid on time. Testing and other quality control
techniques are used to the extent TI deems necessary. TI does not test all parameters of each EVM.
User's claims against TI under this Section 2 are void if User fails to notify TI of any apparent defects in the EVMs within ten (10)
business days after delivery, or of any hidden defects with ten (10) business days after the defect has been detected.
2.3 TI's sole liability shall be at its option to repair or replace EVMs that fail to conform to the warranty set forth above, or credit
User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the warranty
period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to repair or
replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall be
warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
WARNING
Evaluation Kits are intended solely for use by technically qualified,
professional electronics experts who are familiar with the dangers
and application risks associated with handling electrical mechanical
components, systems, and subsystems.
User shall operate the Evaluation Kit within TI’s recommended
guidelines and any applicable legal or environmental requirements
as well as reasonable and customary safeguards. Failure to set up
and/or operate the Evaluation Kit within TI’s recommended
guidelines may result in personal injury or death or property
damage. Proper set up entails following TI’s instructions for
electrical ratings of interface circuits such as input, output and
electrical loads.
NOTE:
EXPOSURE TO ELECTROSTATIC DISCHARGE (ESD) MAY CAUSE DEGREDATION OR FAILURE OF THE EVALUATION
KIT; TI RECOMMENDS STORAGE OF THE EVALUATION KIT IN A PROTECTIVE ESD BAG.

www.ti.com
2
3Regulatory Notices:
3.1 United States
3.1.1 Notice applicable to EVMs not FCC-Approved:
FCC NOTICE: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software
associated with the kit to determine whether to incorporate such items in a finished product and software developers to write
software applications for use with the end product. This kit is not a finished product and when assembled may not be resold or
otherwise marketed unless all required FCC equipment authorizations are first obtained. Operation is subject to the condition
that this product not cause harmful interference to licensed radio stations and that this product accept harmful interference.
Unless the assembled kit is designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must
operate under the authority of an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210 or RSS-247
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.

www.ti.com
3
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required to follow the
instructions set forth by Radio Law of Japan, which includes, but is not limited to, the instructions below with respect to EVMs
(which for the avoidance of doubt are stated strictly for convenience and should be verified by User):
1. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
2. Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
3. Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
2. 実験局の免許を取得後ご使用いただく。
3. 技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧ください。http:/
/www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
3.4 European Union
3.4.1 For EVMs subject to EU Directive 2014/30/EU (Electromagnetic Compatibility Directive):
This is a class A product intended for use in environments other than domestic environments that are connected to a
low-voltage power-supply network that supplies buildings used for domestic purposes. In a domestic environment this
product may cause radio interference in which case the user may be required to take adequate measures.