Texecom Speech Dialler User manual

Speech Dialler Installation Manual
Installation Manual
Voice & Text Dialler
THANK YOU FOR VOTING TEXECOM

Speech Dialler Installation Manual
2 INS232-2
1. Overview
Introduction
Alarm Control Panel
Telephone
Auxiliary
Input
Telephone
Network
Speech Dialler
Intruder (3)
PA (2)
Fire (1)
Aux (4)
Contact 1
SMS
Service
Centre
Mobile
Network
or
Contact 2
or
Contact 3
or
Contact 4
or
Contact 5
or
Contact 6
or
Contact 7
or
Contact 8
or
4 ghi
2 abc
3 def
7 pqrs
5 jkl
8 tuv
0
6 mno
9 wxyz
1
.....Ready.....
The Speech Dialler provides a means of communicating alarm information from an
alarm control panel to a standard or mobile telephone. The unit is normally connected
to an alarm control panel, which provides the necessary power and battery backup.
The unit is also connected to a standard telephone line and behaves like another
extension to the telephone and does not affect its normal operation or that of any
other extension fitted.

Speech Dialler Installation Manual
INS232-2 3
Inputs: The dialler has four trigger inputs; each input can be assigned a voice
message and/or a text message (Speech & Text only). The trigger inputs are normally
connected to the alarm control panel communicator outputs or bell output. Other
devices such as smoke detectors or temperature sensors can be directly connected
to the trigger inputs. The polarity of the trigger inputs can be programmed as either
+ve or -ve applied.
Contacts: Up to 8 contacts may be stored in the unit; each contact can be assigned a
name, telephone number, message type and acknowledgment type.
The unit must NOT be used to call the Police via the Emergency Services
phone numbers.
Voice Messages: The dialler has a built-in microphone and speaker so that audio
messages can be recorded and replayed directly from the unit. Up to four separate
voice messages can be stored; each message can be up to 32 seconds long.
Message 1 is related to trigger input 1; message 2 is related to trigger input 2 and so
on. Voice messages should therefore be recorded to reflect the type of alarm that is
connected to the trigger input, e.g. if input 1 is connected to the “Fire” output on the
alarm/fire control panel then message 1 should state that there is a fire alarm at the
premises.
Text Messages: The Speech & Text model can also send text messages to mobile
telephones using the SMS text service (Short Message Service). The unit does this by
calling a SMS service centre, which takes the text message from the dialler and
forwards it to the contact’s mobile telephone. The unit can store up to four 32-
character “alarm” messages and one common “site details” message. When the unit
sends a text message it appends the “alarm” message to the “site details” message.
The “site details” message would normally hold the name or details of the premises
being protected.
Acknowledgement: On receiving a voice message call from the dialler the contact
person answering the call can acknowledge it at any time by pressing number [8] key
on their telephone. If the voice message is not acknowledged then it is repeated ten
times, after which the dialler abandons the call and dials the next available contact.
Each contact can be configured to either acknowledge the call only or acknowledge
and stop the dialling sequence, i.e., after pressing the [8] key on their telephone the
call is acknowledged and no more contacts are dialled.
Call-Abort: The dialler has several call-abort options, which include restoring the
trigger input or by entering the operator’s passcode. When the unit is aborted it
immediately shuts down and returns to its normal standby mode.
!
"

Speech Dialler Installation Manual
4 INS232-2
Outputs: The dialler has two programmable outputs that can be used to indicate the
status of the unit. The outputs can also be programmed for “remote control”, this
allows you to remotely turn outputs on and off with a touch-tone telephone.
Listen-In Mode: When activated the listen-in mode switches the internal and remote
microphones onto the telephone line so that you can hear activity at the protected
site. The listen-in mode can be activated by the contact at the time of receiving a voice
message or by dialling the protected site and using the Remote Access feature.
Talkback Mode: When activated the talkback mode switches the internal loudspeaker
onto the telephone line so that you can talk to the protected site. The talkback mode
can be activated by the contact at the time of receiving a voice message or by dialling
the protected site and using the Remote Access feature.
Memo: The memo feature allows you to record up to 32 seconds of audio which can
then be played back. This feature can be accessed locally at the unit or by dialling the
protected site and using the Remote Access feature. When a new memo is recorded
the unit will indicate it on the display and optionally give a beep. The memo feature
can also be programmed to automatically record when a trigger input is activated.
Remote Access: If enabled the dialler can be accessed remotely by dialling into the
unit with a touch-tone telephone. Once connected you can turn on and off the two
outputs, activate the listen-in or talkback mode, listen to the memo, or record a new
memo.
Remote UDL: The unit can be remotely programmed using Wintex Upload/Download
software.
Context Sensitive Help: When programming or operating the dialler you can press
the help key and the unit will scroll the relevant information on the display.
Speech Dialler Models: Two versions of the Speech Dialler are available:
•Speech & Text: This model supports both speech and text messages.
•Speech Only: This model only supports speech messages.

Speech Dialler Installation Manual
INS232-2 5
2. Installation
General
The unit requires a 12V @100mA DC power source, which is normally supplied by the
auxiliary power output of an intruder alarm control panel. If the unit is not connected to
an alarm control panel then a suitable power supply will be required.
A 1.5 metre telephone lead is supplied with the unit, which plugs directly into any
standard telephone socket. It is therefore recommended that the unit be sited as near
to a telephone socket as possible. If this it not possible an approved BT extension
lead may be required or the unit can be hard wired to the telephone socket using the
appropriate cable.
Mounting
1. Open the unit by carefully inserting a small flat-blade screwdriver into each slot
at the base of the unit. Gently push the screwdriver to ease the retaining clips
upward, DO NOT LEVER OR TWIST. Excessive force is NOT required.
2. Remove the front flap and front cover and unplug the loudspeaker from the
main circuit board.
3. Mount the unit using at least three appropriate countersunk screws (no larger
than No. 6). A keyhole slot has been provided to assist mounting and aid
leveling.
4. Pass the necessary cables into the base through the cable entries and then
secure the base of the unit to the wall.
The telephone cable must be routed into the base using either the top right
or bottom right knockout cable entry. A screw mount cable tie has been
provided to allow the telephone cable to be secured to the base of the unit.
The cable tie should be fitted to either the top or bottom right fixing holes.
#"

Speech Dialler Installation Manual
6 INS232-2
PCB Layout
OP1-
Tamp
1
2
6
4
OP2-
12340V 12V
Trigger Inputs
R1 T1 R T
3 5
Mic
$Telephone connections (TNV)
%Tamper switch
&Programmable outputs, tamper and remote microphone connections (SELV)
'Microphone
(Trigger Inputs and power supply connections (SELV)
)Loudspeaker connector (SELV)
Connection terminals on the dialler are described as either “Safety Extra Low Voltage”
circuits (SELV) or “Telecommunications Network Voltage” circuits (TNV).
•It is important that the TNV connections are only connected to the PSTN, and
SELV circuits are only connected to other circuits designated as SELV circuits.
•Interconnection circuits should be such that the equipment continues to comply
with the requirements of 4.2 of EN 41003 for TNV circuits and 2.3 of EN 60950
for SELV circuits, after making connections between circuits.

Speech Dialler Installation Manual
INS232-2 7
Connections to the Control Panel
Before making any connections to the unit, isolate ALL power from the control
panel (AC mains and battery). Do not continue if there is power still present on the
control panel.
+12V & 0V: These terminals must be connected to the 12V auxiliary power supply of
the alarm control panel.
Trigger 1 - 4: These terminals should be connected to the relevant outputs on the
alarm control panel. When the input is triggered the dialler will initiate the calling
sequence and play the relevant speech and/or text message. The diagram below
show the various wiring options for the trigger inputs:
N.C.
Loop
12340V 12V
Trigger Inputs
1KW
N.O.
Loop
12340V 12V
Trigger Inputs
+12V when active
(+ve applied)
12340V 12V
Trigger Inputs
Trigger Inputs programmed for +ve operation
N.C.
Loop
12340V 12V
Trigger Inputs
1KW
N.O.
Loop
12340V 12V
Trigger Inputs
0V when active
(+ve removed)
12340V 12V
Trigger Inputs
Trigger Inputs programmed for -ve operation
Tamp: These terminals provide tamper protection for the dialler and should be
connected to the auxiliary tamper circuit on the alarm control panel.
OP1 & OP2: Two programmable switched –ve @100mA outputs.
Mic: A Texecom Remote Microphone Module can be connected to this input, to
enhance the listen-in mode.

Speech Dialler Installation Manual
8 INS232-2
Control Panel Connection Table
The table below shows connection details for various alarm control panels:
Trigger Inputs
Control Panel 1
Fire
2
PA
3
Intruder
Trigger
Polarity +12V 0V
A1 Advantage N/A N/A Bell - -ve Aux + Aux -
ADE Accenta 6 N/A N/A B -ve 13V + 13V -
ADE Concept 6 N/A N/A B -ve 13V + 13V -
ADE Optima 2+ Fire PA Intruder -ve 13V + 13V -
ADE Optima XM N/A N/A B -ve 13V + 13V -
Ademco Infra 6 N/A N/A 3 +ve Aux + Aux -
Ademco Infra 16 1* 2 3 +ve Aux + Aux -
C & K 700L N/A N/A S- -ve Aux + Aux -
CQR Premier 9 FA* PA IA +ve Aux 12V Aux 0V
DA Abacus 6 N/A N/A Bell -ve +12V 0V
DA Abacus 8 N/A N/A Bell -ve +12V 0V
Gardtec 500 Series N/A N/A Bell - -ve Power + Power -
Gardtec 800 Series D1* PA 12Hr -ve 12V 0V
Menvier TS400/TS410 Zone 4 Zone 5 ALM -ve Aux + Aux -
Menvier TS510 N/A OP 2 * OP 1 * +ve Aux + Aux -
Menvier TS690R OP 1 OP 2 OP 3 -ve Aux + Aux -
Menvier Networker Series Digi 1 Digi 2 Digi 3 -ve Aux + Aux -
Pyronix Paragon +/E N/A N/A BA -ve Aux + Aux -
Pyronix Octagon N/A PA ALM -ve Aux + Aux -
Pyronix Conqueror N/A N/A BA -ve Aux + Aux -
Scantronic 9448 N/A COM 2 COM 3 -ve 12V 0V
Scantronic 9452/3/4/5 N/A COM 1 COM 3 -ve 12V 0V
Scantronic 9750/9850 Pin 1 Pin 2 Pin 3 -ve Pin 9 Pin 8
Texecom Veritas 8 Compact N/A N/A B -ve Aux + Aux -
Texecom Veritas 8/R8 N/A N/A B -ve Aux + Aux -
Texecom Veritas R8 Plus Com 1 Com 2 Com 3 -ve Aux + Aux -
Texecom Veritas Excel Com 1 Com 2 Com 3 -ve Aux + Aux -
Texecom Premier 24 O/P 1 * O/P 2 * O/P 3 * -ve Aux + Aux -
Texecom Premier 48/88/168 Digi 1* Digi 2 * Digi 3 * -ve Aux + Aux -
* Control panel output may require programming to the correct function.

Speech Dialler Installation Manual
INS232-2 9
Connections to the Telephone Line
The easiest way to connect the dialler to the telephone line is to use the telephone
lead that is provided with the unit as shown below:
Black
Yellow
Standard BT telephone plug
R1 T1 R T
Connect to Earth
However, if the lead is not long enough or the serial connection is required the dialler
can be hard wired to the telephone socket as shown below:
3
2
1
6
5
4
White/Blue
BT Master Jack (NTE5)
User accessible connections Cable type 1/0.5mm CW1308
Blue/White
R1 T1 R T
Connect to Earth
To other telephone
extension sockets
Failure to fit an earth cable may prevent proper operation of the system
and will invalidate the Texecom warranty and product approval.
The telephone cable must be secured using the screw mount cable tie
provided.
#"

Speech Dialler Installation Manual
10 INS232-2
Commissioning
1. Once all necessary connections have been made to the unit, re-connect the
loudspeaker to the main circuit board and clip the cover on to the base taking
care not to trap any cables.
2. Re-apply mains power to the control panel and reconnect the battery.
3. The dialler will enter its initialisation mode (15 seconds), during which you can:
•Press the red record !key 5 times to load the factory default parameters
then the "key. The display will show: “!"#$%&'()'*+,,,
-"#$.#)/$&0,,,”.
•Press the #key to select the language then "key to accept.
4. After the unit has finished initializing/loading defaults the display will show
“,,,,1&.$2"#1,,,,”. The unit will beep once if it is a Speech Dialler and
twice if it is a Speech & Text Dialler. To select the programming mode enter the
default passcode of $%&'.
5. The display will show “345)67).898:6;<)!7=6>:6)186>?9@” The unit is
now ready for programming and testing. Please refer to the “Operating
Instructions” for full details.
6. After the dialler has been programmed and tested, secure the front cover with
screw and screw cap that is provided in the spares pack.
Specifications
Supply Voltage: 10 - 14VDC
Current Consumption: 35mA (Standby), 100mA (Active)
Trigger Inputs: 4; +ve applied or +ve removed (5 - 24VDC)
Outputs: 2; Open collector switched –ve @100mA
Telecommunications Approval: CTR21
REN Rating: 1
Dialling Formats: Pulse or DTMF
Dimensions: 140mm x 115mm x 30mm
Packed Weight: 360g (Approximately)

Speech Dialler Installation Manual
INS232-2 11
Standards
The Speech Dialler is manufactured to meet all European Area telecommunication
network requirements. These devices have been approved for use with Council
Decision 98/482/EC for pan-European single terminal connection to the public
switched telephone network (PSTN). However due to differences between the
individual PSTNs provided in different countries, the approval does not in itself give
unconditional assurance of successful operation with every PSTN network termination
point.
In the event of problems, you should contact Technical Support at Texecom Ltd.
The Speech Dialler conforms to European Union (EU) Low Voltage Directive (LVD)
73/23/EEC (amended by 93/68/EEC) and Electro-Magnetic Compatibility (EMC) Directive
89/336/EEC (amended by 92/31/EEC and 93/68/EEC).
The CE mark indicates that this product complies with the European requirements for
safety, health, environment and customer protection.
Warranty
All Texecom products are designed for reliable, trouble-free operation. Quality is carefully
monitored by extensive computerised testing. As a result the Speech Dialler is covered
by a two-year warranty against defects in material or workmanship.
As the dialler is not a complete alarm system but only a part thereof, Texecom cannot
accept responsibility or liability for any damages whatsoever based on a claim that the
dialler failed to function correctly. Due to our policy of continuous improvement Texecom
reserve the right to change specification without prior notice.
Speech Dialler is a Trademark of Texecom Ltd.
The Speech Dialler is protected by UK and/or International Registered Design.
Registered Design Number: 2089016

Texecom Limited, Bradwood Court, St. Crispin Way, Haslingden,
Lancashire BB4 4PW, England.
Technical Support:
Tel: [phone]
Tel: [phone]
Fax: [phone]
© Texecom Ltd. 2000 - 2003
INS232-2