Texecom Premier 412 User manual

User Guide
Premier 412/816/832
IINS195-3

Premier 412/816/832 User Guide
INS195 2
Operating Your Alarm System
This document covers the everyday operation of your alarm system, for details on
more advanced operation and system programming, please refer to the Premier
412/816/832 Master User Manual.
Away Arming the System
Enter your Access code  followed by the /key. The Armed
light will flash and the exit sounder will sound for the duration of the exit time.
Stay Arming the System
Enter your Access code  followed by the key. The system will
normally arm immediately, the Armed light will flash slowly indicating that the
system is Stay armed.
Disarming During Entry
Enter the premises via the designated entry point. The entry tone will sound,
proceed directly to the remote keypad and enter your Access code
.
Disarming When Not in Entry
Proceed directly to the remote keypad and enter your Access code
 followed by the /key. Note: If your system consists of
only one partition you will not have to press the /key.
Bypassing Zones
Enter your Access code  followed by the !key. Enter the zone
or zones to be bypassed e.g. 02, 04 etc. When all required zones have been
selected, press:
/to Away arm the system with the selected zones bypassed
to Stay arm the system with the selected zones bypassed
to return to the normal disarmed state with the selected zones bypassed
Reset Alarms/Faults
Enter your Access code , then enter  or press .
Last Alarm Log
Enter your Access code , and then enter . The remote
keypad will display the zones that caused an alarm when the system was last
armed. Press to return to the normal disarmed state.

Premier 412/816/832 User Guide
INS195 3
Acknowledging a New Service Fault
Should the Service light start flashing, enter your Access code ,
and then enter . The remote keypad will display all Service Faults (see
Service Faults Table on back page). Press or to acknowledge the fault
and return to the normal disarmed state.
Toggle Chime On and Off
Enter your Access code , and then enter ) or .
Change User Access Code
Enter your existing Access code , and then enter . Enter
your new Access code  followed by the /key. Now re-
enter your new Access code  for confirmation.
Abort Communications
Enter your Access code , and then enter .
Operating Your Alarm System with Quick Commands
If your Installer has programmed the Quick Commands the following procedures
can be used:
Away Arming the System
Press the /key. The Armed light will flash and the exit sounder will sound
for the duration of the exit time.
Stay Arming the System
Press the key. The system will normally arm immediately, the Armed light will
flash slowly indicating that the system is Stay armed.
Bypassing Zones
Press the !key. Enter the zone or zones to be bypassed e.g. 02, 04 etc. When
all required zones have been selected, press:
/to Away arm the system with the selected zones bypassed
to Stay arm the system with the selected zones bypassed
to return to the normal disarmed state with the selected zones bypassed

Premier 412/816/832 User Guide
INS195 4
Service Faults Displayed on LED Keypads
Light Fault Condition
1 AC Fail
2 Telephone Line Fault
3 2-Wire Smoke Alarm
4
Box Tamper & Auxiliary Input:
Press )to view type, lights 1 - 5 indicate:
Light 1 = Box Tamper
Light 2 = Auxiliary Tamper
Light 3 = Auxiliary PA
Light 4 = Auxiliary Tamper (UK Bell Module)
Light 5 = Bell Tamper (UK Bell Module)
5 Date or Time Lost
6 Zone Tamper/Trouble
Press to view zone number
7 Keypad Tamper/Removed
Press to view keypad number
8
Equipment Faults
Press to view fault type:
Light 1 = Output 1 Fault
Light 2 = Output 2 Fault
Light 3 = Siren/Bell Fault
Light 4 = 2-Wire Smoke Sensor Fault
Light 5 = Auxiliary Fuse Failed
Light 6 = Battery Fault
Light 7 = Service Timer/Zone Soak Test Failed
Light 8 = Communication Fault

Premier 412/816/832 User Guide
FCC Statement
Operation is subject to the following conditions.
•The device must not cause harmful Interference.
•The device must accept any interference received, including interference
that may cause undesired operation.
LAB545 Premier 816 UL label LAB545 Premier 832 UL label
LAB558 Premier 832 RTC UL Label
Canadian Emissions Statements
This class B digital apparatus complies with Canadian ICES – 003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada
INS195 5

Premier 412/816/832 User Guide
ANSI/SIA CP-01-2007 Defaults.
For the following please see INS141 Master User Manual
FEATURE REQUIREMENT DEFAUL
T
Exit Time Required
(programmable)
60 Seconds
Progress Annunciation / Disable - for
Silent Exit
A
llowed
A
ll annunciators enabled
Exit Time Restart
Required Option
Enabled
A
uto Stay Arm on Unvacated Premises Required Option
(except for remote arm)
Enabled
Exit Time and Progress Annunciation /
Disable - for Remote Arm
A
llowed Option
(for remote arm)
Enabled
Entry Delay(s)
Required
(programmable)
30 Seconds
A
bort Window
–
f
or Non-Fire Zones Required Option
Enabled
A
bort Window Time – for Non-Fire Zones
Required
(programmable)
30 Seconds
A
bort annunciation Required Option
Enabled
Cancel Window
Required
Not required to be
programmable.
Cancel Annunciation Required Option
Enabled
Duress Feature
A
llowed Option
Disabled
Cross Zoning Required Option
Disabled
Programmable Cross Zoning Time
A
llowed
Per manufacturer
Swinger Shutdown Required
(programmable)
One trip
Swinger Shutdown Disable
A
llowed
Enabled
Fire Alarm Verification Required Option
Disabled
Arming and Disarming the alarm system please refer to the UL-CUL notes on Page 7 & 8
System Programming Menus. Please refer to UL-CUL Notes on Page 16
Glossary Please see page 25
INS195 6

Premier 412/816/832 User Guide
Notes

Premier 412/816/832 User Guide
Texecom Limited, Bradwood Court, St. Crispin Way, Haslingden, Lancashire BB4 4PW, England.
© Texecom Limited 2007
INS195