Textron BROUWER TR130 Setup guide

TURF ROLLER
Model TR130
Starting Serial No. 1001
Owner / Operator's Manual
and
Illustrated Parts List
Form # 350019

289 N. Kurzen Rd., PO Box 504, Dalton, OH 44618
Tel. [phone] Fax. [phone]
Date of Purchase: Month ________________Day____________________Year _______________
Dealer Name _________________________Phone__________________
Serial Number ________________________
Model Number ________________________
ALWAYS GIVE MODEL AND SERIAL NUMBER WHEN ORDERING SERVICE PARTS

TABLE OF CONTENTS
INTRODUCTION SECTION 1 page
Specifications ...........................................................................................1-1
Description ...............................................................................................1-1
SAFETY SECTION 2
General Safety .........................................................................................2-1
Operator Safety........................................................................................2-1
PRE-START INSTRUCTIONS SECTION 3
Starting Instructions..................................................................................3-1
Specifications for Fuels and Oils..............................................................3-2
OPERATION SECTION 4
Controls....................................................................................................4-1
Operating Precautions..............................................................................4-1
Freewheel Control....................................................................................4-2
SERVICE SECTION 5
Service Schedule .....................................................................................5-1
PARTS SECTION 6
Figure 1 - Engine and Drive Parts............................................................6-1
Figure 2 - Hydrostatic Drive Parts ............................................................6-3
Figure 3 - Front Roller Parts.....................................................................6-5
Figure 4 - Sprocket Assembly Parts.........................................................6-7
Figure 5 - Decals......................................................................................6-9
WARRANTY....................................................................................last page
Form # 350019 rev 8/96

rev 8/96 1 - 1350019
INTRODUCTION section 1
DESCRIPTION
The Turf Roller TR130 is the compact roller that is
easy to operate and transport - to get that rolling job
done quickly. It has the dual fill / drain plugs and
special rounded-edge design roller to prevent turf
damage and a large rear support roller.
SPECIFICATIONS
Model TR130 Turf Roller
Dimensions:
Overall length _______51 in. (130 cm)
Overall width _______33-1/2 in. (85 cm)
Overall height _______40 in. (102 cm)
Weight__________Empty 425 lbs.
(193.kg) Loaded 840 lbs.
(381 kg)
Drum Size ________24 in. diameter (61
cm) 30 in. wide (76 cm)
Engine:
Honda __________5-1/2 HP
Drive Train:
Speed __________0 - 4.2 MPH
Transmission _______Hydrostatic

350019 2 - 1rev 8/96
ATTENTION: This symbol
identifies potential health
and safety hazards. It
marks safety precautions.
ATTENTION: Your safety
and the safety of others is
involved.
•Read and understand the owner's manual,
before attempting to operate this machine.
•Operate all controls from the operator's seat,
(if so equipped). NO RIDERS.
•Keep all shields in place and safety switches
adjusted properly.
•Do not leave equipment unattended. STOP
the engine and remove the key (if so
equipped).
•Do not allow minors or the inexperienced to
operate this machine.
•Keep people and pets a safe distance away
from machines using power driven
attachments. Injury could result from flying
debris.
OPERATING SAFETY
CAUTION
SAFETY section 2
SIGNAL WORD DEFINITIONS
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury. This signal word is limited to the most extreme cases.
Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in
minor or moderate injury and/or property damage. It may also be used to alert
against unsafe practices.
GENERAL SAFETY
BE ALERT!
•Do not run engine at excessive speeds.
•Do not operate the turf roller unless the chain
and engine guards are securely in place.
•Tomaintaincontrol of themachine,use onlya
lowspeedwhile walkingbeside theturf roller.
•Exercise caution when operating across the
side of a hill. If the hill is too steep (20 degree
incline or more), the machine may tip over
causing personal injury and machine dam-
age. Always walk on the up--hill side of the
turfroller whenoperating onthesideofa hill.
•To prevent accidental movement of the ma-
chine, turn the engine off.
•When parking or unattended -- turn the en-
gine off to prevent movement of the roller.

rev 7/01 3 - 1350019
PRE-START INSTRUCTIONS section 3
BEFORE STARTING:
1. READ SAFETY DECALS
2. Check engine and hydrostatic transmission oil
levels.
3.Visually checkfor looseor missingpartsorbolts.
4. Fill with clean fuel.
STARTING INSTRUCTIONS:
1. Turn the fuel valve to the ON position.
2. Move the choke lever to the CLOSE position.
NOTE: The choke may not be needed if the en-
gine is warm.
3. Move the throttle lever slightly to the left.
4. Turn the engine switch to the ON position.
5. Pull the recoil starter grip lightly until resistance
is felt, then pull briskly. NOTE: Do not allow the
starter grip to snap back against the engine.
6. As the engine warms up, gradually move the
choke lever to the OPEN position.
7. Position throttle for the desired engine speed.
NEVER USE ETHER AS A STARTING AID, OR
SEVERE DAMAGE TO ENGINE MAY OCCUR.
NEVER FILL FUEL TANK WITH ENGINE
RUNNING!
SPECIFICATIONS FOR FUELS AND OILS
ENGINE OIL
Fill the crankcase with oil that meets API service
designation SF, SF/CC, or SF/CD. Do not mix brands
or grades of oil. Recommended weight for general all
temperature use is:
SAE 10W-30 or SAE 10W-40
FUEL
Use clean, fresh, regular or unleaded fuel. Use of
unleaded fuel results in less maintenance.
HYDRAULIC OIL
Fill hydrostatic transmission reservoir to the safe
level with approved hydraulic oil. Use only Steiner
Trans--Hydraulic Oil or SAE 30 engine oil. Do not use
automatic transmission fluid, multi-grade motor oil, or
any other type of hydraulic oil.
USE ONLY STEINER TRANS--HYDRAULIC OIL OR
SAE 30 ENGINE OIL. THE USE OF ANY OTHER OIL
MAY VOID WARRANTY AND IS NOT
RECOMMENDED.

350019 4 - 1rev 8/96
OPERATION section 4
Operating Instructions
ENGINE
The Brouwer Turf Roller is equipped with a 5--1/2 HP
engine.
Complete details and operation instructions can be
found in the engine manufacturer's manual.
LOCATION OF CONTROLS
The hydrostatic drive control is located on the left
side of the steering column.
The freewheel control crank is located on the front of
the hydrostatic air duct.
STARTING THE ENGINE
For complete engine starting and stopping
procedures, see the engine manual.
Always start the engine with
the hydrostatic drive lever in
neutral. Failure to observe this precaution could
result in serious personal injury and/or machine
damage.
CONTROL OPERATIONS
Hydrostatic drive control:
This control governs the travel direction (forward or
reverse) and travel speed of your turf roller. (See
Drawing 1)
To move forward, move lever to the left from neutral.
The further the lever is moved, the faster the forward
travel speed.
To reverse, move the lever to the right from neutral.
The further the lever is moved, the faster the reverse
travel speed.
When the engine is running
and the control lever is in
neutral, the machine can roll if left unattended.
Personal injury or machine damage may result.
Always use a slow steady movement when moving
the control lever from neutral to forward or reverse
so that the machine will not leap forward or reverse
-- not only for the safety of the operator, but also to
prevent damage to the machine.
Abrupt movement of the hydrostatic control lever can
cause the rear roller to lift. Shift slowly to avoid
injury.
Drawing 1 - Forward - Reverse Control

rev 8/96 4 - 2350019
OPERATION section 4
ENGINE SPEED CONTROL
This control is located on the engine. Set engine
speed between 2/3 and full throttle as desired. For
operation, see the engine manual.
Running engine at low throttle
settings could cause
hydrostatic transmission damage due to
inadequate cooling air flow.
FREEWHEEL CONTROL
The freewheel control allows the turf roller to be
moved by external means when the engine has
been shut off. Release the crank lock and turn the
freewheel control crank clockwise to engage the
freewheel and turn counter clockwise to disengage
the freewheel. Re--lock the control crank with the
crank lock. (See Drawing 2)
Do not activate the freewheel
control when the turf roller is
stopped on an incline or when the engine is
running.
Drawing 2 - Freewheel Control

350019 5 - 1rev 7/01
SERVICE section 5
PERIODIC MAINTENANCE
Check the hydrostatic drive oil level daily. Make sure the oil is at the correct
level for hot or cold. Markings for hot or cold levels are located on the breather
level indicator.
Tofilltheexpansion tank,unscrewthereservoir breather cap.Afterfilling to the
correct level, replace the cap. If additional oil is required, use only Steiner
Trans--Hydraulic Oil or SAE 30 engine oil. Do not use automatic transmission
fluid, multi-grade motor oil, or any other type of hydraulic oil.
Change hydraulic oil annually.
Grease the turf rollers with Lithium--based grease every 50 hours or monthly
(whichever occurs first). (See lubrication chart below)
DO NOT GREASE CHAINS. Lubricate chains with SAE 10W-30 motor oil
every 30 hours or weekly (whichever occurs first).
Change engine oil every 100 hours of operation or bi-monthly, whichever
occurs first. Use SAE 10W-30 or SAE 10W-40 with API service designation of
SF, SF/CC, or SF/CD.
Drawing 3 - Lubrication Chart

rev 10/00 6 - 1350019
PARTS section 6
Engine and Drive
Parts
Figure 1

350019 6 - 2rev 12/00
PARTS section 6
Parts List for Figure 1
Ref Part no. Description Quantity
1M5268 ENGINE, HONDA 5.5 HP 1
2115013 CHAIN, ROLLER #50 X 47-1/4" LG 1
381-055 HALF LINK, #50 1
481-053 CONNECTOR LINK, #50 1
5301686 GUARD, CHAIN 1
699-K02 FLANGE BOLT, 5/16 X 1 4
794-05 FLAT WASHER, 5/16 USS 12
895-04 FLAT WASHER, 1/4 SAE 8
10 301429 MOUNT, ENGINE 1
11 F5728 BOLT, 1/2 X 4 GR 5 FULL THREAD 4
12 301723 WASHER, FLAT CUPPED 8
13 M5221 MOUNT, RUBBER 7/16 ID 1-3/8 OD 8
14 F5012 LOCKNUT, 1/2 NYLON JAM 4
15 99-E10 JAM NUT, 1/2 4
16 350003 HANDLEBAR WELDMENT 1
17 350022 DUCT, AIR 1
18 90-0606 BOLT, 3/8 X 3/4 (SERIAL NO. 1001-1398) 6
99-K26 BOLT, FLANGE 1/4 X 3/4 (SERIAL NO. 1399- ) 5
19 96-06 LOCK WASHER, 3/8 (SERIAL NO. 1001-1398) 6
20 90-0624 BOLT, 3/8 X 3 4
21 99-E40 LOCKNUT, NYLON 3/8 4
22 90-0508 BOLT, 5/16 X 1 2
23 95-05 FLAT WASHER, 5/16 SAE 2
24 99-E12 FLANGE NUT, 5/16 2
25 90-0820 BOLT, 1/2 X 2-1/2 2
27 99-E41 LOCKNUT, NYLON 1/2 2
28 90-0822 BOLT, 1/2 X 2-3/4 2
29 96-08 LOCK WASHER, 1/2 2
30 301505 FRAME WELDMENT, FORK 1
31 301522 ROLLER, 8" 1
32 B0002 BEARING, FLANGE 5/8 SET SCREW 2
33 90-0416 BOLT, 1/4 X 2 4
34 99-E39 LOCKNUT, NYLON 1/4 4
35 114025 CHAIN, ROLLER: #40 X 42" LG 1
37 81-056 CONNECTOR LINK, #40 1
38 99-E18 WING NUT, 3/8 1
39 301690 CRANK, FREE WHEEL 1
40 90-0512 BOLT, 5/16 X 1-1/2 4
41 94-05 FLAT WASHER, 5/16 USS 8
42 99-E38 LOCKNUT, NYLON 5/16 4
43 90-0610 BOLT, 3/8 X 1-1/4 1
44 92-06 NUT, 3/8 1
45 95-06 FLAT WASHER, 3/8 SAE 4

rev 5/00 6 - 3350019
PARTS section 6
Hydrostatic Drive
Parts
Figure 2

350019 6 - 4rev 12/00
PARTS section 6
Parts List for Figure 2
Ref Part no. Description Quantity
185-K0312 KEY, SQ. 3/16 X 3/16 X 1-1/2 (C/W ENGINE) 1
2301656 COUPLING, HALF 1
387-021 INSERT, JS4U BROWNING 1
4301456 COUPLING, HALF 1
5301748 FAN, 7" OD 1
601-043 SCREW, MACHINE 10-24 X 3/8 4
7F0080 WASHER, #10 SHAKEPROOF 4
885-W0204 KEY, WOODRUFF 1/8 X 1/2 2
9D8011 HYDROSTATIC TRANSMISSION 1
*21-990314 SEAL KIT 1
10 301457 DRIVE SPROCKET 1
11 90-0610 BOLT, 3/8 X 1-1/4 1
12 43-006A ROD END, 3/8 2
13 93-06 NUT, 3/8-24 NF 4
14 95-06 FLAT WASHER, 3/8 SAE 6
15 41-065 SPRING, COMPRESSION 2
16 99-E13 FLANGE NUT, 3/8 1
17 99-E40 LOCKNUT, NYLON 3/8 1
18 350014 ARM WELDMENT, F-R CONTROL 1
19 85-W0204 KEY, WOODRUFF 1/8 X 1/2 1
20 350012 ROD, NEUTRAL ADJUSTMENT 1
21 99-K27 BOLT, FLANGE 1/4 X 1 2
22 350011 RETAINER, NEUTRAL SPRING 1
23 03-0610 CLEVIS PIN, 3/8 X 1-1/4 1
24 02-CP0406 COTTER PIN, 1/8 X 3/4 2
25 350010 ROD WELDMENT, F-R CONNECTING 1
26 350006 LEVER WELDMENT, SPEED CONTROL 1
27 99-E21 JAM NUT, 3/8 1
28 21-101680-156 SNAP RING 1
29 21-97121 RETAINING RING 1
30 21-90797 INPUT SHAFT BEARING 1
31 21-62184 INPUT SHAFT 1
32 21-93955 INPUT SHAFT SEAL 1
33 D8047 RESERVOIR 1
34 D8048 RESERVOIR CAP 1
35 350025 BRACKET, REVERSE STOP 1
36 350024 BRACKET, FORWARD STOP 1
37 99-K26 FLANGE BOLT, 1/4 X 3/4 2
38 F1002 JAM NUT, 1/4 1
39 F1603 SET SCREW, 1/4 X 1-1/2 SQHD 1
40 99-E20 FLANGE NUT, 1/4 2
41 94-04 FLAT WASHER, 1/4 USS 2
* Not Illustrated

rev 5/00 6 - 5350019
PARTS section 6
Front Roller
Parts
Figure 3

350019 6 - 6rev 5/00
PARTS section 6
Parts List for Figure 3
Ref Part no. Description Quantity
1A31611 ROLLER ASSY, FRONT (Incl. Ref. 2 - 14) 1
299-E21 JAM NUT, 3/8 1
399-K33 BOLT, 3/8 x 2 ALL THREAD GRADE 2 1
492-07 NUT, 7/16 6
595-07 FLAT WASHER, 7/16 SAE 6
690-0712 BOLT, 7/16 X 1-1/2 5
7F4705 BOLT, 7/16 X 2-1/4 NF GRADE 8 1
890-0718 BOLT, 7/16 X 2-1/4 1
9301466 FRAME, FRONT COVER 1
10 301541 SCRAPER, ROLLER 1
11 301551 SPACER, ROLLER SCRAPER 1
12 301664 WASHER 1
13 90-0710 BOLT, 7/16 X 1-1/4 1
14 96-07 LOCK WASHER, 7/16 7
15 A31609 ROLLER ASSEMBLY, 24" DIA (Incl. Ref. 16 - 21) 1
16 301513 ROLLER, WELDMENT 24" OD 30" LG 1
17 301697 SPROCKET, ROLLER 1
18 B0108 BEARING, 1" 2 BOLT FLANGE 2
19 99-E01 WHEEL NUT, 1/2 NF 4
20 99-E26 JAM NUT, 1/2 NF 4
21 H8030 PLUG, 3/4" NPT SQUARE HEAD 2

rev 5/00 6 - 7350019
PARTS section 6
Sprocket Assembly
Parts
Figure 4

350019 6 - 8rev 5/00
PARTS section 6
Parts List for Figure 4
Ref Part no. Description Quantity
1A31628 ASSEMBLY, SPROCKET IDLER SPINDLE (Incl Ref. 2-11) 1
2301758 SPROCKET WELDMENT, IDLER 1
3M5222 PLUG, PLASTIC SNAP IN 1-1/4" 1
4G1515 RING, RETAINING, EXT. 3/4 SHAFT 1
5L4006 RING, INNER .75" ID X 1" OD X 3/4 LONG 1
6B3003 BEARING, NEEDLE 1"ID X 3/4 LG 1
7L4007 WASHER, THRUST 3/4" ID 1
8B2014 BEARING, BALL 1
9G1001 RING, RETAINING 1
10 301755 SPINDLE, 3/4" 1
11 F4705 BOLT, 7/16 X 2-1/4 NF GRADE 8 1
12 96-07 LOCK WASHER, 7/16 1

rev 10/00 6 - 9350019
PARTS section 6
Decals
Figure 5
NFR
BEFOREUSE:
Makesure all guardsarein place.
Cleararea ofbystanders.
DURINGUSE:
Wearhearing protection.
Avoidsudden machine movements,move
shift leverSLOWLY.
Avoidroll over:
-stayoff side slopeswhen rollersare empty.
-avoidside slopesgreaterthan 20°
when rollersarefull.
Stop engine when leaving unit.
Beforerefuelling,allowengine tocool.
Do notparkunitwithfree-wheeling plunger
depressed.
2
7
8
6
4
5
6
3
1

350019 6 - 10 rev 10/00
PARTS section 6
Parts List for Figure 5
Ref Part no. Description Quantity
1A31639 DECAL, PACKAGE (Includes Ref. 2 - 8) 1
2301678 DECAL, F. N. R. 1
3301775 DECAL, MAINTENANCE 1
4301800 DECAL, OPERATING INSTRUCTIONS 1
5301799 DECAL, CAUTION / SAFETY INSTRUCTIONS 1
6401257 DECAL, “BROUWER” 2-1/2 X 10 2
7301771 DECAL, ENGINE THROTTLE 1
800-209 DECAL, MADE IN USA 1