Ronbow Signature Series Assembly instructions

INSTALLATION AND CARE GUIDE
BRIT WALL CABINET
E027013

BRIT WAll Cabinet
Model : E027013
161027ronbow.eu | ronbow.comINSTALLATION SHEET
1
Designed By: DANELONMERONI | UNITED KINGDOM
Tools Required
PRE-INSTALLATION
3 long screws
1 set of wall cleats
2 glass shelves
8 shelf clips
1 2x4 beam
Materials Included
Materials Required

BRIT WAll Cabinet
Model : E027013
161027ronbow.eu | ronbow.comINSTALLATION SHEET
2
Designed By: DANELONMERONI | UNITED KINGDOM
See Figure 1.
See Figure 2.
Step 1: Determine the ideal location of your
new wall cabinet.
NOTE: Make sure the location has at
least two studs. Front notch the studs
and install a 2x4 beam.
Figure 1.
Step 2: Install the wall cleat at the desired lo-
cation and drill pilot holes.
Fasten the cleat to the wall.
Verify the cleat is level.
Figure 2.
Step 3: Secure the cleat in the back of the
cabinet to the wall cleat.
Check if the wall cabinet is level.
INSTALLATION

BRIT WAll Cabinet
Model : E027013
161027ronbow.eu | ronbow.comINSTALLATION SHEET
3
Designed By: DANELONMERONI | UNITED KINGDOM
See Figure 4.
See Figure 3.
Step 1: Unhinge the door by popping o the
hinge from the base of the cabinet.
Figure 3.
Step 2: Unscrew the hinge plate from the base
of the cabinet.
Measure the distances of the existing
screw holes and copy that to the
oppposite side.
Figure 4.
Step 3:
Step 4:
Install the hinge plate.
REVERSE DOOR OPENING FOR INVERTED INSTALLATION
Bracket
Hook
Install the door to the base of the
cabinet. Push the hinge until you hear
a click to lock the hinge into place.
Cup

BRIT WAll Cabinet
Model : E027013
161027ronbow.eu | ronbow.comINSTALLATION SHEET
4
Designed By: DANELONMERONI | UNITED KINGDOM
See Figure 5.
Step 1: Unhinge the door by popping o the
hinge from the base of the cabinet.
See page 3.
Figure 5.
Step 2: Unscrew the shelf clip from
the under-side.
Remove the glass shelf.
REMOVE GLASS SHELVES

BRIT WAll Cabinet
Model : E027013
161027ronbow.eu | ronbow.comINSTALLATION SHEET
5
Designed By: DANELONMERONI | UNITED KINGDOM
Figure 6.
Locate the screw nearest the hinge
cup and rotate clockwise or counter-
clockwise to move the door from side
to side.
Locate the screw furthest away from
the hinge cup and turn the screw
clockwise or counter-clockwise to
move the door from front to back.
Locate the screw pictured in Figure 6.
Turn the screw clockwise or counter-
clockwise to move the door from top
to bottom.
ADJUST DOOR HINGE
Figure 7.
Figure 8.
NOTE: When adjusting the door hinges keep in mind
to adjust the other hinges.
Side to Side
Front to Back
Top to Bottom
See Figure 6.
See Figure 7.
See Figure 8.
Side
Depth
Height

BRIT WAll Cabinet
Model : E027013
161027ronbow.eu | ronbow.comINSTALLATION SHEET
6
Designed By: DANELONMERONI | UNITED KINGDOM
Wood Surfaces
Recommended Products
The fine furniture finish of your new vanity, mirror or other bathroom accessories are designed to
protect against normal home use. With proper care, your product will provide years of use and beauty
in your home.
General Care Tips
PRODUCT CARE AND MAINTENANCE
• If a spill occurs, clean and dry the surface immediately as liquid can soak through the surface and cause
greater damage.
• Do not place in direct sunlight. Exposure to sunlight may affect the appearance of your vanity, and the
finish will eventually crack.
• Keep away from direct sources of extreme temperatures as heat, cold or moisture from humidity.
Color changes, or blemishes in the wood can occur if recommended care of is not met. Try to avoid
these extremes.
• Most wood surfaces can be cleaned, or dusted, with any commercial wood cleaning product. For general
cleaning, use a non-abrasive, or lint-free cloth while dusting along the wood grain to preserve the
wood’s chacteristics.
• Pledge Orange Oil, or similar
• Orange-Glo Wood Cleaner
DISCLAIMERS: Wood naturally ages, darkens and changes color over time due to several environmental conditions that may cause materials to vary from their
original color and/or to warp, split or crack. These variations are considered to be the nature of the material in relation to their environmental exposure and may
be significant over a long period of time. The eectiveness of cleaning Ronbow product is dependant on various factors that include sunlight, smoke, moisture,
household cleaners and/or amount of cleaning product used over time. Ronbow cannot guarantee that the above Product Care & Maintenance methods will
eectively clean your product.
• Test cleaning product on small, discrete area prior to applying to entire surface.
• Wipe surfaces frequently with dry, soft, non-abrasive and lint-free towel.
• Do not allow liquids and moisture to accumulate on the surface of products.
• For warranty information, please visit our website at www.ronbow.com or contact the Customer Service
Department at [phone].

161027
40650 Encyclopedia Circle
Fremont, CA 94538
T 510.713.1188
F 510.657.9388 ronbow.eu | ronbow.com