The Land of Nod Jenny Lind Crib User manual

- Failure to follow these warnings and assembly instructions could result in serious injury or death.
- Read all instructions before assembling crib. Keep instructions for future use.
-Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding
under an infant.
-To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
Strangulation Hazard:
- Strings can cause strangulation! DO NOT place items with a string, cord or ribbon around a child’s neck,
such as hood strings or pacifier cords. DO NOT suspend strings over crib or toddler bed, or attach strings to
toys for any reason.
-To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on loose
fasteners.
- DO NOT place crib or toddler bed near windows where cords from blinds or drapes may strangle a child.
Fall Hazard:
- When child is able to pull to standing position, set mattress to lowest position and remove bumper pads,
large toys and other objects that could serve as steps for climbing out.
-When child is able to climb out or reaches the height of 35 inches (90 cm), the crib shall no longer be used
and the child should be placed in a youth or regular bed.
CAUTION: ANY MATTRESS USED IN THIS CRIB
MUST BE AT LEAST 27-1/4 INCHES (69 cm) BY 51-5/8
INCHES (131 cm) WITH A THICKNESS NOT EXCEEDING
6 INCHES (15 cm).
- Check this product for damaged hardware, loose joints, missing pats or sharp edges before and after
assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT use crib if any
parts are missing, damaged, or broken. Contact The Land of Nod® for replacement parts and instructional
literature if needed. DO NOT substitute parts.
- If refinishing, use a non-toxic finish specified for children’s products.
- Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
- Infants can suffocate in gaps between crib sides and a mattress that is too small.
- Periodically check to see that all bolts are securely tightened.
- To clean crib: Wipe with clean soft cloth dampened with a mild cleanser and water. Rinse with clean water
using a soft cloth, and dry thoroughly.
- Follow warnings on all products in a crib.
- When a vaporizer is in use, always aim vapor steam away from the crib as well as away from other wood
furniture.
WARNING:
!
!
WARNING:
!
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Jenny Lind Crib Assembly Instructions
Made in Vietnam - r08

1 - Small Allen wrench 1 - Large Allen wrench
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Jenny Lind Crib Assembly Instructions
Page 1 of 6
Made in Vietnam - r08
This page lists the contents included in the box. Please take
time to identify the hardware as well as the individual
components of the product. As you unpack and prepare for
assembly, place the contents on a carpeted or padded area
to protect them from damage. Please follow the assembly
instructions closely. Improper assembly can result in
personal or property damage.
Note: 2 adults are required to safely assemble this product.
WARNING:
CHOKING HAZARD - SMALL PARTS
Small parts present in unassembled state.
Adult assembly required.
4 - Flat
washers
4 - Set
screws
4 - Spring
washers
4 - Brackets 4 - Corner
supports
1 - Phillips head screwdriver
NOT INCLUDED
4 - Bolts
4 - Cam screws
4 - Barrel cams
4 - Bolt caps

The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Jenny Lind Crib Assembly Instructions
Page 2 of 6
Made in Vietnam - r08
2 - End panels
2 - Side panels
1 - Mattress support panel

1
2
Insert 1 barrel cam into side panel as shown, making sure the barrel cam opening is aligned with through hole in upper
end of the side panel. Next, fit the side panel over corresponding cam screw attached to the end panel and fasten barrel
cam with a set screw as shown. Secure set screw with a screwdriver. Attach 1 bolt, 1 spring washer, 1 flat washer and 1
bracket through side panel into end panel as shown, and secure with a small Allen wrench. Do not over tighten the bolts.
Insert 2 cam screws into each end panel as shown. Secure, but do not over tighten, cam screws with a Phillips head
screwdriver.
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Jenny Lind Crib Assembly Instructions
Page 3 of 6
Made in Vietnam - r08

3
4
Insert 1 barrel cam into side panel as shown, making sure the barrel cam opening is aligned with through hole in upper end
of the side panel. Next, fit the side panel over corresponding cam screw attached to the end panel and fasten barrel cam
with a set screw as shown. Secure set screw with a screwdriver. Attach 1 bolt, 1 spring washer, 1 flat washer and 1 bracket
through side panel into end panel as shown, and secure with a small Allen wrench. Do not over tighten the bolts.
Insert 1 barrel cam into side panel as shown, making sure the barrel cam opening is aligned with through hole in upper end
of the side panel. Next, fit the side panel over corresponding cam screw attached to the end panel and fasten barrel cam
with a set screw as shown. Secure set screw with a screwdriver. Attach 1 bolt, 1 spring washer, 1 flat washer and 1 bracket
through side panel into end panel as shown, and secure with a small Allen wrench. Do not over tighten the bolts.
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Jenny Lind Crib Assembly Instructions
Page 4 of 6
Made in Vietnam - r08

5
6
Determine desired height (low, middle, high) for the crib mattress. Insert 1 corner support into each corner of the crib
assembly as shown.
The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Jenny Lind Crib Assembly Instructions
Page 5 of 6
Made in Vietnam - r08
With assistance of another adult, carefully place mattress support panel into crib assembly and onto corresponding
corner supports. Using a large Allen wrench, secure each corner support with 1 bolt cap. Turn bolt caps clockwise to
secure. Assembly is now complete.
high
middle
low

The Land of Nod
8135 River Drive • Morton Grove, IL 60053 • p: [phone] • e: [email protected] • www.landofnod.com
Jenny Lind Crib Assembly Instructions
Page 6 of 6
Made in Vietnam - r08
CLEANINGANDCARE:
Cleansurfaceswithadryordampsoftcloth.Donotuseabrasivecleaners. Periodically check and tighten hardware as necessary.
Once the crib is in use, periodically check to make sure all bolts are tight, and tighten as necessary. Keep these
instructions for future use.
MAINTENANCE
Upon completion of assembly, be sure all screws, bolts and fastening devices have been tightened securely.
Periodically repeat this check to make sure all screws, bolts and fastening devices are tight. Before each usage or
assembly, inspect crib for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use crib if parts
are missing or broken. DO NOT substitute parts. DO NOT make any alteration to this crib.
CLEANING
Mix together a mild solution of gentle dishwashing liquid and water, apply to crib surface using a soft clean cloth
lightly dampened in the solution. Rinse with clean water again using a soft clean cloth, then dry all surfaces
thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL OR COARSE RAGS
SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
STORAGE
After completing the assembly process you are advised to read and beware of all WARNINGS, CAUTIONS,
CLEANING, STORAGE, USE AND MAINTENANCE notices contained in these instructions. For long term storage of
the crib, store in a cool, dry place and keep away from moisture and extreme temperature changes.