L.L.Bean SEASHORE User manual

SEASHORE IRON BED
Thank you for purchasing our product Seashore iron bed. Assembly of this product
requires an open wrench (not included) and Allen wrench (included-item). We have
found it helpful to have a second person present during the assembly process.
0FCY7/8/9&FDA10073003

STEP 1
Read through these instructions thoroughly before
beginning assembly. We have found this to be of
great value when first assembling this product.
STEP 2
Remove all parts and hardware from packing
material. Bed should be placed on a clean, non-
abrasive surface to prevent soiling fabric or
scratching metal pieces.
STEP 3
Identify all parts using description at right.
PARTS
STEP 4
Assembly of this product requires these tools: open
wrench (not included) and Allen wrench
(included-item number 7). We have found it
helpful to have a second person present during
the assembly process.
1 of 4 0FCY7/8/9&FDA10073003

STEP 5 (TWIN & FULL) A- Swing out CROSS ARMS to 90 degrees as shown in Figure 1. For 634 only: Slide (12) END CAPS
onto side rails (9). WARNING: END CAPS MUST BE PLACED OVER ENDS OF SIDE RAILS TO AVOID SERIOUS INJURY.
B- Determine the desired bed size (Twin or Full). Overlap CROSS ARMS and engage SHOULDER RIVETS into proper keyholes. Note:
Both rivet heads must engage in keyhole slots. See Figure 2.
C- If optional CENTER SUPPORT is provided: Line up CENTER SUPPORT halfway between SIDE RAILS. Position slots in the CENTER
SUPPORT over holes in CROSS ARMS and bolt together as shown in Figure 3
D- Install GLIDES as shown in Figure 4. METAL RINGS should be used on corner glides.
STEP 6 (QUEEN & KING) A- Swing out CROSS ARMS to 90 degrees as shown in Figure 1. For 656 only: Slide END CAPS
onto end of side rails. WARNING: END CAPS MUST BE PLACED OVER ENDS OF SIDE RAILS TO AVOID SERIOUS INJURY.
B- Turn CENTER SUPPORT over with legs pointing up. Attach CENTER CROSS ARM by inserting RIVET “A” into NOTCH “A” then
pivot so RIVET “B” locks into NOTCH “B” as shown in Figure 2. Repeat with both CENTER CROSS ARMS.
C- Determine desired bedding size (Queen, Cal. King, or King). Note: The 856 Bed Frame does not accommodate California King bedding.
Slide SHOULDER RIVETS into proper keyholes of CENTER CROSS ARMS as indicated in Figure 3. Note: Both rivet heads must engage
in keyhole slots.
D- Install GLIDES as shown in Figure 4. METAL RINGS should be used on corner GLIDES.
2 of 4 0FCY7/8/9&FDA10073003

STEP 7- Align top reduction of extension legs (8) with bottom of headboard posts. Make sure the 3 holes on extension legs are
perpendicular to headboard panel. Now carefully insert extension legs (8) into bottom of headboard (1) posts.
STEP 8- Place headboard and frame in desired location in room. Place 2 screws (3) through holes located in leg (8). Align bed
frame bracket over screws. Place a flat washer (6) and a nut (5) on each screw. Hand-Tighten, DO NOT TIGHTEN screws all the
way. Repeat on other side of headboard. Tighten all screws securely using the Allen wrench (7).
STEP 9- Position footboard panel (2) and align holes in the post with holes in the frame bracket. Place flat washer (6) on each
screw (4). Insert through bracket and into post. Hand-tighten, DO NOT TIGHTEN screws all the way. Repeat on other side of
footboard panel. Tighten all screws securely using the Allen wrench (7).
3 of 4 0FCY7/8/9&FDA10073003

CARE
Vacuuming is the only recommended
cleaning method for the mattresses. Do
not dry clean. The chemicals used in dry
cleaning agents and spot removers may be
harmful to the fabric or underlying
material. A solution of mild soap and cold
water may be applied lightly to tackle a
stain, making sure not to soak the
mattress.
www.llbean.com
Product Support 1 800 341 4341
4 of 4 0FCY7/8/9&FDA10073003