Thermalright Macho Direct User manual

Thermalright
Macho Direct

× 1
× 1
4
8
× 8
× 1
× 4
× 5
× 3
× 5
× 4
× 4
Chill Factor 2g
Macho Direct
Assembly package

Macho Direct
1
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
Intel 1150/1151/1155/1156
Heatsink Body Fan Clip
TY-140 Black
Anti-Vibration Pads
Mounting Plate
M3L6 Screw
M3L7 Screw
Screw Nut
Back Plate (Intel)
Motherboard
M3L8 Screw

The Ultimate Cooling Solutions!
www.thermalright.com
2
Component
1
1
2
2
3
3
4 5 6
7 8
9
9
10
13
11
12
12
13
1110
Macho Heatsink Body ×1
Thermal paste ×1 Screw driver ×1
Back Plate ×1
M3L8 Screw ×5
M3L7 Screw ×3
Anchoring Mount ×1
Screw Nut ×4
Chill Factor 2g
M3 L6 Screw ×5 Anti-Vibration Pad x8
4 5 76 8
LGA2011 Type B
Screw Pillars x4
Fan Clip ×4
TY-140 Black ×1

3
Installation Instructions:
Step 1:
Step 2:
Step 3:
Step 1 : Fan clips installaion
Take out Macho Direct Heat-sink from the color box. Pull both ends of the fan clip and make them go
through holes on the corners of the heat-sink (as shown in the picture.) Repeat for the other fan clip.
Leave both fan clips on the heat-sink body for fan installation later on . Do not remove them.
Step 2 : Backplate Installation
Make four M3L8 Screw Pillars go through the Backplate from bottom towards top. And then place the
Backplate on the table. Put the four washers (for Intel) around the Screw Pillars.
Step 3 : Place the motherboard on top of the Back Plate. See the four Screw Pillars go through the four
holes around the processor socket.Cap the four Screw Pillars with the four Screw Nuts.Make sure the
side with a washer is facing the Back Plate.
1150
1151
1155
1156
12
4
3

The Ultimate Cooling Solutions!
www.thermalright.com
4
Step 4: Step 5:
Step 6: Step 7:
Step 8: Step 9:
Chill Factor 2g Chill Factor 2g
Chill Factor
2g
Chill Factor
2g
Step 8: Fan Installation
Place the included TY-140 Black onto the Heatsink
Body. And then secure it with the Fan Clips, by
pulling the Fan Clips to place the four ends at the
four holes on the TY-140 Black.
Step 5 : Applying Thermal Paste
Apply the Thermal Paste to the base of the heat-
sink and the surface of the CPU evenly. (A at
edge, like a business card or an old credit card
would be beneficial in spreading the thermal
paste.)
Step 9: Installation completed
Plug in the fan connector to the CPU PWM Fan
socket on the motherboard. Installation complete.
Step 6: Easy Access
Pass the supplied Screw
Driver through the central hole
of the Heatsink Body, for easier
access to the M3L7 Screw with
washer underneath the cooler.
Step 7: Apply fan cushion pads
Among the parts you will
find four pads that look like
elongated diamonds with a
whole in the center. Apply one
of the pads over each of the
four holes in the fan, please
take care to put them over
the holes on the fan according to your choice of
airflow. For push configuration (air flowing thru
the heat sink, apply as shown in the drawing. For
pull conguration (air being sucked out of the heat
sink), place them on the opposite side of the fan.
Then install the fan in your choice of conguration,
with the pads on the fan facing the heat sink.
12
4
3
Step 4 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw
Nuts. Use the four M3L6 Screws to fix the
Anchoring Mount on to the Screw Nuts.

Macho Direct
5
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
LGA2011 Type B Screw Pillars
Intel 2011/2011-3
Heatsink Body Fan Clip
TY-140 Black
Anti-Vibration Pads
Mounting Plate
M3L6 Screw
Motherboard
M3L7 Screw

Macho Direct
The Ultimate Cooling Solutions!
www.thermalright.com
6
Component
1
1
2
2
3
3
4 5 6
7 8
9
9
10
13
11
12
12
13
1110
Macho Heatsink Body ×1
Thermal paste ×1 Screw driver ×1
Back Plate ×1
M3L8 Screw ×5
M3L7 Screw ×3
Anchoring Mount ×1
Screw Nut ×4
Chill Factor 2g
M3 L6 Screw ×5 Anti-Vibration Pad x8
4 5 76 8
LGA2011 Type B
Screw Pillars x4
Fan Clip ×4
TY-140 Black ×1

7
Installation Instructions:
Step 1:
Step 2:
Step 3:
Step 1 : Fan clips installaion
Take out Macho Direct Heat-sink from the color box. Pull both ends of the fan clip and make them go
through holes on the corners of the heat-sink (as shown in the picture.) Repeat for the other fan clip.
Leave both fan clips on the heat-sink body for fan installation later on . Do not remove them.
Step 2 : Screw Pillar Installation
Place the motherboard (the processor installed) on top of the desk or a workbench. Fix the four included
LGA2011 Type B Screw Pillars into the heat-sink studs on the Intel ILM Assembly Frame around the
processor socket in a criss-cross pattern.
Step 3 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw Pillars. Use the four M3L6 Screws to x the Anchoring Mount
on to the Screw Pillars, also in a criss-cross pattern to ensure balanced mounting.
1
1
2
2
4
4
3
3

Macho Direct
The Ultimate Cooling Solutions!
www.thermalright.com
8
Step 4:
Step 5:
Step 7: Step 8:
Step 7 : Fan Installation
Place the included TY-140 Black onto the Heatsink
Body. And then secure it with the Fan Clips, by
pulling the Fan Clips to place the four ends at the
four holes on the TY-140 Black.
Step 4 : Applying Thermal Paste
Apply the Thermal Paste to the base of the heat-sink and the surface of the CPU evenly. (A at edge,
like a business card or an old credit card would be benecial in spreading the thermal paste.)
Step 8 : Installation completed
Plug in the fan connector to the CPU PWM Fan
socket on the motherboard. Installation complete.
Step 5: Easy Access
Pass the supplied Screw
Driver through the central
hole of the Heatsink Body,
for easier access to the
M3L7 Screw with washer
underneath the cooler.
Chill Factor
2g
Chill Factor
2g
Chill Factor
2g
Chill Factor
2g
Step 6:
Step 7: Apply fan cushion pads
Among the parts you will
find four pads that look like
elongated diamonds with a
whole in the center. Apply one
of the pads over each of the
four holes in the fan, please
take care to put them over the
holes on the fan according to
your choice of airow. For push conguration (air
owing thru the heat sink, apply as shown in the
drawing. For pull conguration (air being sucked
out of the heat sink), place them on the opposite
side of the fan. Then install the fan in your choice
of conguration, with the pads on the fan facing
the heat sink.

Macho Direct
9
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
AM2/AM2+/AM3/AM3+/FM1
Heatsink Body Fan Clip
TY-140 Black
Anti-Vibration Pads
Mounting Plate
M3L6 Screw
M3L7 Screw
Screw Nut
Back Plate (AMD)
Motherboard
M3L8 Screw

Macho Direct
The Ultimate Cooling Solutions!
www.thermalright.com
10
Component
1
1
2
2
3
3
4 5 6
7 8
9
9
10
13
11
12
12
13
1110
Macho Heatsink Body ×1
Thermal paste ×1 Screw driver ×1
Back Plate ×1
M3L8 Screw ×5
M3L7 Screw ×3
Anchoring Mount ×1
Screw Nut ×4
Chill Factor 2g
M3 L6 Screw ×5 Anti-Vibration Pad x8
4 5 76 8
LGA2011 Type B
Screw Pillars x4
Fan Clip ×4
TY-140 Black ×1

11
Installation Instructions:
Step 1:
Step 2:
Step 3:
Step 1 : Fan clips installaion
Take out Macho Direct Heat-sink from the color box. Pull both ends of the fan clip and make them go
through holes on the corners of the heat-sink (as shown in the picture.) Repeat for the other fan clip.
Leave both fan clips on the heat-sink body for fan installation later on . Do not remove them.
Step 2 : Backplate Installation
Make four M3L8 Screw Pillars go through the Backplate from bottom towards top. And then place the
Backplate on the table. Put the four washers (for AMD) around the Screw Pillars.
Step 3 : Place the motherboard on top of the Back Plate. See the four Screw Pillars go through the four
holes around the processor socket.Cap the four Screw Pillars with the four Screw Nuts.Make sure the
side with a washer is facing the Back Plate.
AMD
12
4
3

The Ultimate Cooling Solutions!
www.thermalright.com
12
Step 4: Step 5:
Step 6: Step 7:
Step 8: Step 9:
Chill Factor 2g Chill Factor 2g
Chill Factor
2g
Chill Factor
2g
Step 8: Fan Installation
Place the included TY-140 Black onto the Heatsink
Body. And then secure it with the Fan Clips, by
pulling the Fan Clips to place the four ends at the
four holes on the TY-140 Black.
Step 5 : Applying Thermal Paste
Apply the Thermal Paste to the base of the heat-
sink and the surface of the CPU evenly. (A at
edge, like a business card or an old credit card
would be beneficial in spreading the thermal
paste.)
Step 9: Installation completed
Plug in the fan connector to the CPU PWM Fan
socket on the motherboard. Installation complete.
Step 6: Easy Access
Pass the supplied Screw
Driver through the central hole
of the Heatsink Body, for easier
access to the M3L7 Screw with
washer underneath the cooler.
Step 7: Apply fan cushion pads
Among the parts you will
find four pads that look like
elongated diamonds with a
whole in the center. Apply one
of the pads over each of the
four holes in the fan, please
take care to put them over
the holes on the fan according to your choice of
airflow. For push configuration (air flowing thru
the heat sink, apply as shown in the drawing. For
pull conguration (air being sucked out of the heat
sink), place them on the opposite side of the fan.
Then install the fan in your choice of conguration,
with the pads on the fan facing the heat sink.
Step 4 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw
Nuts.Use the four M3L6 Screws to fix the
Anchoring Mount on to the Screw Nuts.
12
4
3

Macho Direct
13
Technical Spec
Heatsink Specifications:
Dimension: Length 140mm x Width 102mm x Height 158mm
Weight: 660g
Heatpipe: 6mm heatpipe*5 units
Copper Base: C1100 Pure copper
Fan Specification:
Dimension: L152mm x H140mm x W26.5m
Weight: 160g
Fan speed: 300~1300RPM (4-Pin PWM)
Fan noise: 15~21dBAdBA MAX (4-Pin PWM)
Airflow: 16.9~73.6CFM MAX
Connector: 4 Pin (PWM Fan connector)

The Ultimate Cooling Solutions!
www.thermalright.com
14
117.05
78.5523.45
15.05158.35
140
140 78.5523.45
41.3
38.3

Macho Direct
15
Awards

The Ultimate Cooling Solutions!
www.thermalright.com
TEL: [phone]
FAX: [phone]
EMAIL: [email protected]