Thermalright Archon IB-E X2 User manual

Thermalright
Archon IB-E X2

Archon IB-E X2
Assembly Package
× 4
× 7
× 1
× 1
× 1
4
4
8
× 4
× 5
× 1
× 8
× 1
× 4
× 4
× 4
× 1
× 1

Archon IB-E X2
1
Intel 775/1150/1151/1155/1156/1366
Exploded View
Heatsink Body
14cm Fan Clip
TY-141SV FAN
M3 L10 Screw
Mylar Film
Metal Back Plate
Anti Vibration Pad
Mounting Plate
M3 L6 Screw
Back Plate Cap
(For LGA775)
Anchoring Mount
Screw Nut
Intel Washer (small)
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.themalright.com

The Ultimate Cooling Solutions!
www.thermalright.com
2
Component
1
1
2
2
3
3
4
4
5
5
6
6
7 8
9
9
10 11
10
13
16
14
15 16 17
11
13
12
15
14
7 8
12
Heatsink Body ×1
LGA2011 Type B
Screw Pillars x4
M3 L6 Screw ×7
Back Plate Cap ×1
Mylar Film×1
Chill Factor III ×1
Intel Washer (small) ×4
Mounting Plate ×1
Metal Back Plate ×1
M3 L10 Screw ×5
AMD Washer (big) ×4
Anchoring Mount ×1
Screw Nut ×4
14cm Fan Clip ×4
Anti Vibration Pad ×8
TY-141SV Fan ×2
17
PWM Y-cable ×1

3
Installation Instructions:
Step 1:
Step 3: Step 4:
Step 2:
Step 4 : Place the motherboard on top of the Back
Plate. See the four Screw Pillars go through the
four holes around the processor socket. Cap the
four Screw Pillars with the four Screw Nuts in
a criss-cross pattern.Make sure the side with a
washer is facing the Back Plate.
Step 1 : Part Installation
Take out Archon IBE X2 heat-sink body from the brown box. Apply Anti-Vibration Paddings to 4 corners
on both sides of the Heatsink Body. Pull both ends of the Fan clip and make them go through holes
on the corners of the heat-sink. Repeat for the other three fan clips. Leave all four fan clips on the
Heatsink Body for fan install later on. Do not remove them.
12
4
3
Step 3 : 775 Back Plate cap
Note: When installing on a 775 platform, please
rst insert the Back Plate Cap into the opening on
the Back plate, make sure you have the Cap facing
downwards. Only for LGA775 platform, all other
platforms go directly to Step 4.
Step 2 : Back Plate Installation
Choose the platform (LGA 775/1150/1151/1155/1156/1366) you are in use. Make four M3L10 Screw
Pillars go through the Metal Back Plate and the Mylar lm from bottom towards top.And then place the
Metal Back Plate on the table. Put the four Washers (for Intel) around the Screw Pillars.
1366
775
1150
1151
1155
1156

Step 6:
Step 7:
Step 8: Step 9:
Step 8 : Fan Installation
Place the included TY-141SV fan onto the
Heatsink body. And then secure it with the Fan
Clips, by pulling the Fan Clips to place the four
ends at the four holes on the TY-141SV fan, Now
repeat the same for the second fan on the other
side of the heat-sink.
Step 7 : Mounting Plate Installation
Place the Heatsink Body on top of the CPU. Make Mounting Plate go through the Heatsink Body. And
then use the two M3L6 screws to secure the Mounting Plate, one side at a time in several turns to
ensure balanced mounting.
Step 9 : Installation completed
Connect the two TY-141SV fans to the PWM
Y-Cable then connect the cable to the CPU PWM
Fan socket on the motherboard. Installation
complete.
Step 6 :Applying Thermal Paste
Apply the included Thermal Paste, Chill Factor
III to the base of the Heatsink and the surface
of the CPU evenly. (A at edge, like a business
card or an old credit card would be benecial in
spreading the thermal paste.)
Step 5:
Step 5 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw
Nuts. Use the four M3L6 Screws to fix the
Anchoring Mount on to the Screw Nuts.
12
4
3

Archon IB-E X2
5
Exploded view
Heatsink Body
TY-141SV FAN
Anti Vibration Pad
Mounting Plate
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.themalright.com
M3 L6 Screw Anchoring Mount
LGA2011 Type B
Screw Pillars
Intel 2011/2011-3/2066
14cm Fan Clip

The Ultimate Cooling Solutions!
www.thermalright.com
6
Component
1
1
2
2
3
3
4
4
5
5
6
6
7 8
9
9
10 11
10
13
16
14
15 16 17
11
13
12
15
14
7 8
12
Heatsink Body ×1
LGA2011 Type B
Screw Pillars x4
M3 L6 Screw ×7
Back Plate Cap ×1
Mylar Film×1
Chill Factor III ×1
Intel Washer (small) ×4
Mounting Plate ×1
Metal Back Plate ×1
M3 L10 Screw ×5
AMD Washer (big) ×4
Anchoring Mount ×1
Screw Nut ×4
14cm Fan Clip ×4
Anti Vibration Pad ×8
TY-141SV Fan ×2
17
PWM Y-cable ×1

7
Installation Instructions:
Step 1:
Step 2:
Step 3:
Step 3 : Screw Pillar Installation
Screw on the four LGA2011 Type B Screw Pillars into the Heatsink studs on the ILM Assembly Frame
around the processor socket.
Step 2 : Anchoring Mount Installation
Place the Anchoring Mount onto the four LGA2011 Type B Screw Pillars, secure it by tightening it with 4
M3L6 Screws.
Step 1 : Part Installation
Take out Archon IBE X2 heat-sink body from the brown box. Apply Anti-Vibration Paddings to 4 corners
on both sides of the Heatsink Body. Pull both ends of the Fan clip and make them go through holes on
the corners of the heat-sink. Repeat for the other three fan clips. Leave all four fan clips on the Heatsink
Body for fan install later on. Do not remove them.
1
1
2
2
4
4
3
3