Thermo Scientific Smart2Pure Pro Owner's manual

Installation and Operation
50157544 • Revision A • October 2018
Thermo Scientific Barnstead
Smart2Pure Pro Ultrapure water
system

IMPORTANT Read this instruction manual. Failure to follow the instructions in this manual can result in
damage to the unit, injury to operating personnel, and poor equipment performance.
CAUTION All internal adjustments and maintenance must be performed by qualified service personnel.
Material in this manual is for informational purposes only. The contents and the product it describes are
subject to change without notice. Thermo Fisher Scientific makes no representations or warranties with
respect to this manual. In no event shall Thermo be held liable for any damages, direct or incidental, arising
from or related to the use of this manual.
© 2018 Thermo Fisher Scientific Inc. All rights reserved.

Contents
Preface ........................................................................ 1
Legal Information...................................................... 1
Warranty .................................................................. 1
Explanatory Notes on the Operating Instructions...... 1
Standards and Directives ......................................... 2
Transport and Packaging............................................. 3
Examination on Receipt............................................ 3
Complaints............................................................... 3
Packaging for Return Shipment................................ 3
Safety Precautions....................................................... 4
Contents...................................................................... 6
Contents of Smart2Pure Pro .................................... 6
Smart2Pure Pro System........................................... 8
Smart2Pure Pro System 30 L and 60 L Tanks.......... 8
Intended Use of the Device .......................................... 9
Technical Specifications............................................... 10
The Installation Area..................................................... 14
Wall Mounting the Smart2Pure Pro .......................... 14
Attaching the Wall Mounting Bracket
for 30 L or 60 L Pure Water Tank ............................. 15
Installation.................................................................... 19
Connections of the Smart2Pure Pro System ............ 19
Connections of the Smart2Pure Pro Pure
Water Storage Tank ................................................. 20

Water Connections of Smart2Pure Pro System ........ 20
Smart2Pure Pro Flow Chart ......................................... 25
How the Smart2Pure Pro System Functions ................ 26
Initial Start Up .............................................................. 27
Putting the System into Operation............................ 27
Dispensing Water from the Dispensing Valve............ 28
Install and Vent the 0.1 μm Final Filter ...................... 28
Operating Elements ..................................................... 30
Flow Chart of Menu System Control......................... 31
System Control............................................................ 32
General Information.................................................. 32
User Menu ............................................................... 32
OEM Menu............................................................... 32
Service Menu ........................................................... 34
Maintenance ................................................................ 35
Maintenance Intervals............................................... 35
Replacing the Ultrapure Cartridge............................. 35
Replacing the RO Cartridge...................................... 36
Check the Concentrate Flow of RO.......................... 37
Disinfection .............................................................. 37
Changing the Ultrafilter............................................. 38
UV-Reactor Assembly .............................................. 40
Replacing the UV Lamp............................................ 40
Replacing the 0.1 μm Final Filter............................... 41
Waste Disposal............................................................ 43
Troubleshooting........................................................... 44

Replacement Parts ...................................................... 46
Replacement Parts: Smart2Pure Pro........................ 46
Replacement Parts: Pure Water Tank
for Smart2Pure Pro .................................................. 47
Consumables............................................................... 48
Accessories ............................................................. 48
Terminal Assignment.................................................... 49
Maintenance Record.................................................... 50

Smart2Pure Pro Ultrapure water system Preface | 1
Preface
These operating instructions are protected by copyright.
Rights resulting thereof, particularly reprint, photomechanical
or digital post-processing or reproduction, even in parts, are
only allowed with the written consent of Thermo Fisher
Scientific. This regulation does not apply to reproductions for
in-plant use. The contents of this operating instructions
manual may change at any time and without any prior notice.
In case of conflicting translations into foreign languages the
English-language version of these operating instructions shall
be binding.
Read through the information given in these operating
instructions on installing and operating the system before you
begin installation and use of your water purification system.
This is of particular importance, as we, the manufacturer, do
not assume any liability for damage due to incorrect operation
or use of the system other than the intended use.
Thermo Fisher Scientific Inc. provides this document to its
customers with a product purchase to use in the product
operation. This document is copyright protected. Any
reproduction of the whole or any part of this document is
strictly prohibited, except with the written authorization of
Thermo Fisher Scientific Inc. The contents of this document
are subject to change without notice. All technical information
in this document is for reference purposes only. System
configurations and specifications in this document supersede
all previous information received by the purchaser.
Thermo Fisher Scientific Inc. makes no representations that
this document is complete, accurate or error-free and
assumes no responsibility and will not be liable for any errors,
omissions, damage or loss that might result from any use of
this document, even if the information in the document is
followed properly.
This document is not part of any sales contract between
Thermo Fisher Scientific Inc. and a purchaser. This document
shall in no way govern or modify any Terms and Conditions of
Sale, which Terms and Conditions of Sale shall govern all
conflicting information between the two documents.
Legal Information
Note: Specifications, terms and pricing are subject to
change. Not all products are available in all countries. consult
your local sales representative for details.
Warranty
Thermo Fisher Scientific warrants the operational safety and
functions of the Thermo Scientific Barnstead Ultrapure Water
Systems only under the condition that:
• The system is installed and operated as per the operation
manual. Do not use this product for anything other than
its intended use.
• The system feed-water is not modified.
• Only original spare parts and accessories that have been
approved by Thermo Fisher Scientific are used (third-
party spares without Thermo Fisher Scientific approval
will void the limited warranty).
• Inspections and maintenance are performed at the
specified intervals.
• An installation verification test is performed on
commissioning the system for the first time and repeated
after each preventative maintenance and repair activity.
The warranty is valid from the date of delivery of the
system to the customer.
• The above mentioned warranty conditions are subject to
the general terms and conditions of sale, in effect at the
time of purchase, which apply as well.
Explanatory Notes on the
Operating Instructions
EU Mark of Conformity
CSA - admission
CAUTION: This symbol, in the context of a
CAUTION, indicates a potentially hazardous
situation which if not avoided could result in minor
to moderate injury or damage to the equipment.
WARNING: This symbol, in the context of a
WARNING, indicates potentially hazardous
situations which, if not avoided, could result in
serious injury or death.

2 | Preface Smart2Pure Pro Ultrapure water system
This information is valid for the system that is received. For
quick and correct service, include the following information on
all inquiries and replacement parts orders which relate to your
system:
• The serial number (located on the right side of the system
on the nameplate)
• The catalog number
Standards and Directives
The Thermo Scientific Barnstead Ultrapure Water Systems
complies with the following standards and directives:
• Low Voltage Directive 2014/35/EC
• EMC Directive 2014/30/EU
• ASTM D1193-6
• RoHs 2011/65/EU
Additionally, the ultrapure water system is in compliance with
many other international standards, regulations and directives
not listed here. Should you have any questions regarding
compliance with national standards, regulations and
directives applicable for your country, contact your Thermo
Fisher Scientific sales organization.
DANGER: This symbol, in the context of a
DANGER, indicates potentially hazardous
situations which, if not avoided, could result in
serious injury or death.
This symbol indicates situations where dangerous
voltages exist and potential for electrical shock is
present. Electrical work on the system is only to be
carried out by qualified personnel.
This symbol represents protective conductor
connection. Connect the power supply to an
electrical socket with a protective connection.
This symbol indicates a need to use gloves during
the indicated procedures.
This symbol indicates a need to wear protective
goggles gloves during the indicated procedures.
This symbol indicates a situation in which
breathing protection must be used.
Note: Is used for application hints and useful information.

Smart2Pure Pro Ultrapure water system Transport and Packaging | 3
Transport and Packaging
Ultrapure water systems are carefully inspected and packed
prior to shipping, but damage could still possibly occur during
transport. Lifting and carrying the Thermo Scientific
Barnstead Smart2Pure Pro ultrapure water system, e.g. to
the installation location, should be carried out by two people.
Examination on Receipt
1. Ensure all components for complete system was ordered
and received. This should include:
• Smart2Pure Pro water system
• Pretreatment
• Storage tank 30 L or 60 L
• Wall bracket for Smart2Pure Pro water system (if wall
mounting)
• Wall bracket for 30 L or 60 L tank (if wall mounting)
2. Carefully unpack system and inspect system for damage.
Note: If the packaging show signs of damage, inspect the
system for damage.
Figure 1. Unpacking
Complaints
If there has been any damage occurred to the goods during
transportation:
• Immediately contact your delivery transport agency.
• Save the complete packaging, including the cardboard
box, for a possible inspection of them and/or return
shipment of the system.
Packaging for Return
Shipment
If possible, use the original box and packaging material. When
these are no longer available, then:
• Protect the system from shock by packing it in bubble
wrap and/or packaging foam and a strong cardboard
box.
Note: The time limit for claims is 6 days from the time of
receipt of the goods. The right to claim for damages ceases
when this time has elapsed.
Note:
• Only a trained person should take the system out of
operation.
• Prior to sending back an operated device, empty the
water, dry the system and take out the cartridges.
• Pack the ultrapure cartridges into a bubble wrap and/or
packaging foam and put it into the package of the
Smart2Pure Pro ultrapure water system.
DANGER: Do not pull the plastic foil over your
head. Risk of suffocation. Use the plastic foil only
for packaging.

4 | Safety Precautions Smart2Pure Pro Ultrapure water system
Safety Precautions
Observe these safety precautions for your own safety!
• Do not install or operate the system until you have
carefully read through these operating instructions and
the notes and notices contained therein.
• Lifting and carrying the ultrapure water system, e.g. to
the installation location, should be carried out by two
people. To do this, lift the system in tandem at the two
corner points beneath the bottom plate.
• The CE mark is nullified if you make any structural
changes to the system or install products from other
manufacturers in/on the system.
• Protect the system from frost. The temperature at the
installation area must be between +2°C and +40°C.
• Always observe the applicable, pertinent codes and
regulations valid at the installation location of the system
and follow all applicable accident prevention regulations.
• The feed-water pressure must be at least 2 bar and at
max. 6 bar or 29 to 87 PSI. When the feed-water
pressure is higher, install an external pressure reducer.
• A low pressure check valve is recommended to prevent
back flow of feed-water from water system.
• A grounded 100 - 240 V, 50/60 Hz electrical outlet must
be available (refer to Electrical Connections table in the
section Technical Specifications).
• Access to the power supply cord and plug may never be
restricted or obstructed.
• Unplug the system from the power outlet for all
maintenance work on the system.
• An atmospherically vented floor drain with a nominal
diameter of at least 63 mm (2.48 inch) (DN50 tube) must
be present at the installation location. If no drain is
provided it is recommended that a water detector be
installed for safety reasons (for European specifications
only). Failure to provide this will release the manufacturer
from liability for any water-induced damage that may
result.
• Proceed as follows if the system is not to be operated for
an extended period, e.g., over extended weekend, or
during a vacation period:
- Switch the system OFF or unplug the mains plug
- Close the feed-water inlet (close the feed-water tap)
The pump will be damaged if the system runs without any
supply of feed-water. The manufacturer will not accept
any liability if this occur.
• The system must be disinfected or rinsed after an
extended down time. The disinfection procedure is
described under section Disinfection.
• The surface or wall on which the system is to be installed
or mounted must have an adequate load-carrying
capacity (check the maximum capacity of load the wall
can sustain and stability of the wall). The dry and wet
weight of the system is given under section Technical
Specifications.
• The surface on which the system is installed must be
level and stable not to exceed a maximum of 2%
deviation from evenness is recommended.
• When installing the water purification system, always
ensure that there is adequate space all around the
system (refer to the section Technical Specifications)
to ensure that ease of use or easy replacement of
materials (e.g., filter change, connection) is possible at all
times.
• Visually inspect the system at regular intervals. Clean up
any water or spills found around the system immediately.
CAUTION: The Thermo Scientific Barnstead
Ultrapure Water Systems are modern water
purification system intended solely for the
treatment of potable water. The water it produces
is not fit for drinking.
DANGER: Work may only be performed on the
system electronics when the system has been
switched OFF and when ESD protection is in
place. Only specially trained personnel may work
on the system’s electronics.
WARNING: Never look directly into a switched
ON UV-lamp, as UV-light endangers eyesight and
exposure to body may causes skin irritation.
CAUTION: To avoid the risk of pinching, crushing,
cutting or electrical shock, never perform
maintenance on the system without its protective
housing, or while it is in operation. Maintenance
work on the system may only be performed by
trained, authorized specialists.

Smart2Pure Pro Ultrapure water system Safety Precautions | 5
Note: The Hg content in the UV lamp is so low so that no
damage to the environment can arise.
• To avoid tripping, ensure that the tubing do not lay over
the floor.
• Apply the general rules of hygiene for laboratories when
working with the system.
• Proceed as follows when the system has a defect:
- Switch the system OFF and unplug the system from
power outlet.
- Shut off the feed-water supply.
- Contact your local service organization.
• Wear safety gloves when working with
disinfection solutions.
• If your skin should come into contact with a
chlorine product, rinse it immediately with
ample, fresh water.
• The system, or system components, may
heat up as a result of a defect. It is
recommended to always wear appropriate
safety gloves to prevent skin damage or
burns.
• Wear safety gloves when changing the UV
lamp, in order to prevent that your skin comes
in contact with the UV lamp glass.
• Wear safety glasses when working with
disinfection solutions.
• If your eyes come into contact with a chlorine
product, rinse them immediately with ample,
fresh water and contact a physician at once.
• Check the UV-lamp before initial start.
• If the UV-lamp is broken
- Wear a breathing protector, filter category
FFP3 and replace the UV lamp. For
disposal the UV lamp refer to the section
Waste Disposal.
- Ventilate the room well.

6 | Contents Smart2Pure Pro Ultrapure water system
Contents
Contents of Smart2Pure Pro
The following items are included with the Smart2Pure Pro water system:
Table 1. Content List of Smart2Pure Pro
Sr
No. Item Item Number
11 x Smart2Pure Pro ultrapure water system 50157573
21 x Ultrapure cartridge 09.1020
31 x RO cartridge 50157608
Including 1 x Assembly kit consisting of:
41 x Final filter (sterile filter 0.1 m) 50157375
51 x Feed-water connecting kit 25.0071
61 x Connecting tube outer diameter ¼“ 6 m / 8.22 inch 18.0137
12
5
10, 11
6
7
817
4
13
14
19
18
9
15
20
21
16
23
22

Smart2Pure Pro Ultrapure water system Contents | 7
71 x External Dispenser Valve ¼“ 50158317
81 x Disinfection Adapter 50133431
91 x Table Top Power Pack 50149597
10 1 x Universal Adapter 21.1006
11 1 x Universal Holder 21.1007
12 1 x Rubber connector to nema plug connector 50132200
13 1 x Rubber connector to British ST plug connector 50132203
14 1 x Rubber connector to Euro plug connector 50132215
15 1 x Plug Angle Connector ¼” 50157605
16 1 x RO Flush assembly 50157605
17 1 x T-Connector ¼” 14.0362
18 1 x Female Adaptor ½” BSP Thread x ¼” Tube OD 50157861
19 1 x PE Tubing 8 mm 18.0036
20 1 x PE Tubing 6 mm 50148369
21 1 x Straight Reduction Connector, D8 mm - D6 mm 14.0318
22 2 x Nylon Dowel Plug S6 6 x 30 mm 21.0002
23 2 x Screw DIN 7997 4 x 35 ZNPL 21.0069
Additional Required Accessories:
24
1 x Ultrapure water tank:
- 30 L storage tank
Or
- 60 L storage tank
50155494
50155499
25 1 x Pretreatment Assembly 50157886
Table 1. Content List of Smart2Pure Pro
Sr
No. Item Item Number

8 | Contents Smart2Pure Pro Ultrapure water system
Smart2Pure Pro System
Smart2Pure Pro System 30 L and 60 L Tanks
Note: Smart2Pure Pro will not operate with Smart2Pure 12 storage tanks.

Smart2Pure Pro Ultrapure water system Intended Use of the Device | 9
Intended Use of the Device
The Thermo Scientific Barnstead Ultrapure Water Systems
are laboratory systems used for the treatment of water. The
system allows the purification of water into the water
categories mentioned in the standards of ASTM 11.01 and
ASTM 11.02.
The Thermo Scientific Barnstead Ultrapure Water system are
designed to be installed and used in the following application
areas:
• Laboratories for cell biological and biotechnological work
with the safety levels L1, L2 and L3.
• Medical and microbiological laboratories according to
DIN EN 12128.
• Laboratories in the central area of clinics and hospitals.
The system must not be operated outside of the
specifications as described in the operating manual. In
particular, the system should not be used for production of
drinking water and drugs manufacturing. The system must
not be used as a medical device and outside of laboratories.

10 | Technical Specifications Smart2Pure Pro Ultrapure water system
Technical Specifications
Note: Check at regular intervals the quality of your feed-water.
*RO flows at 15°C
Feed-water requirements
Source Potable tap water pretreated with Barnstead Pretreatment System (50157886)
Silt density index (SDI) <3
Turbidity <1 NTU
Conductivity (reference
temperature +25 °C) 1500 S/cm (670 ·cm)
Hardness Hardness stabilized
Chlorine Max. 0.1 ppm
pH range 4 - 11
Temperature +2°C - +35°C
Pressure 2 - 6 bar / 29 - 87 PSI (at a pressure >6 bar / 87 PSI a pressure reducer must be
installed upstream of the system.
Product water quality ASTM Type I
(from dispensing valve) UV/UF
Conductivity (reference
temperature +25°C) S/cm 0.055
Resistance (reference
temperature +25°C) M·cm 18.2
Product water quality ASTM Type II
(tank quality) UV/UF
Conductivity (reference
temperature +25°C) S/cm 0.1 – 1.0
Resistance (reference
temperature +25°C) M·cm 1 - 10
Retention rate for bacteria and
particles %99
External tank capacity
Smart2Pure Pro Liter 30 or 60
Smart2Pure Pro RO cartridge
permeate flow* L/hr 16lph +/-15%
Smart2Pure Pro RO cartridge
concentrate flow* L/hr 60
TOC value ppb 1 - 5
RNase ng/ml <0.003
DNase pg/ul <0.4
Bacteria CFU/ml <0.01
Bacterial endotoxins EU/ml <0.001
Particle >0.2m, #/ml m/ml <1
Dispense rate L/min up to 1

Smart2Pure Pro Ultrapure water system Technical Specifications | 11
Figure 2. Smart2Pure Pro Dimensions
Dimensions and weight of Smart2Pure Pro
Height 545 mm / 21.46 inch
Width 305 mm / 12.01 inch
Depth 300 mm / 11.81 inch
Base Area 277 x 372 mm / 10.91 x 14.65 inch
Weight including ultrapure cartridge and RO cartridge 28 kg / 61.74 lbs
305 mm (12.01”) 300 mm (11.81”)
545 mm
(21.46”)
Clearance around Smart2Pure Pro systems
and pure water tank
Clearance on left and right from
the side of the system
At least 300 mm /
11.81 inch
Top space At least 400 mm /
15.75
inch
Materials in contact with water
Adjustable pressure
retaining valve
NBR = Acrylnitril Butadien
Rubber
Pump head Nylon with glass fibre
UV lamp High-purity synthetic quartz
UV housing Stainless steel
Ultrapure cartridge PP = Polypropylene
UF housing PC = Polycarbonate

12 | Technical Specifications Smart2Pure Pro Ultrapure water system
Figure 3. 30 L and 60 L pure water tank dimensions
Note: A minimum of 250 mm (10") clearance is needed above the tank.
Rinsing solenoid valve PA = Polyamide
Dispensing valve PET =
Polyethyleneterephthalate
Conductivity measuring
cell
POM = Polyoxymethylen,
stainless steel
Distributor block POM = Polyoxymethylen
Materials in contact with water
Connections POM = Polyoxymethylen
Tubing PE = Polyethylene
O-Rings EPDM = Ethylene propylene
diene rubber
Materials in contact with water
Dimensions and weight 30 L and 60 L pure water tank
System 30 L pure water tank 60 L pure water tank
Height 606 mm / 23.86 inch 920 mm / 36.22 inch
Width Ø 388 / 15.28 inch Ø 388 / 15.28 inch
Depth Ø 384 / 15.12 inch Ø 384 / 15.12 inch
Weight with full capacity 37,5 kg / 82.57 lbs 71,5 kg / 157.66 lbs
Height with CO2 Filter 778 mm / 30.63 inch 1092 mm / 43 inch
388 mm (15.28”)
388 mm (15.28”)
778 mm (30.63”)
1092 mm (43”)

Smart2Pure Pro Ultrapure water system Technical Specifications | 13
Water connections
Feed-water tubing Tube ¼” outer diameter
Concentrate tubing Tube ¼” outer diameter
Tank Flow tubing (Smart2Pure Pro) Tube 6 mm outer diameter
Tank back flow tubing (Smart2Pure Pro) Tube 6 mm outer diameter
Remote dispenser tube jumper Tube ¼” outer diameter
External dispensing valve Tube ¼” outer diameter
Electrical connections
Input voltage AC 100 – 240 VAC, 50 – 60 Hz, 2.0 A Max
Output voltage DC 24 V, 5.0 A Max
System connection DC 24 V, 120 W
Serial Interface RS232
Potential free contact Maximum 30 V, 2 A
Protection class Class II (external SMPS certified as Class I)
Ambient conditions During Operation Storage
Operation area Indoor rooms Indoor rooms
Maximum altitude above sea level up to 2000 m up to 2000 m
Temperature range Min. +2°C, Max +40°C, 80% rel. rH,
non-condensing
Min. +2°C, Max. +60°C, 90% rel. rH,
non condensing
Line-voltage variation Not more than +/- 10% of the line
voltage -- (not applicable)
Transient over voltages
As usually occur in the supply network
(overvoltage category II acc. to IEC
60364-4-443)
Note: The rated level of transient
overvoltage is the withstand impulse
voltage acc. to overvoltage category II
of IEC 60364-4-443.
-- (not applicable)
Ventilation requirements no special requirements no special requirements
Degree of pollution 2 2
Airborne sound emission
Sound pressure level 49 dB (A)

14 | The Installation Area Smart2Pure Pro Ultrapure water system
The Installation Area
Note: The operator is obliged to ensure, that the installation of
the water purification unit and its operation are carried out in
compliance with all national and international guidelines,
applicable and valid for the place of installation.
Note: If necessary, measures to protect the drinking water
have to be taken by installing appropriate components.
Take the following criteria into consideration when selecting
the installation area:
• Feed-water pressure (potable tap water) not be less than
2 bar (29 PSI) and not greater than 6 bar (87 PSI).
• There must be a feed-water shut off valve installed ahead
of the Smart2Pure Pro system, with a male ¾” NPT fitting
for connection.
• Minimum air temperature +2°C, Maximum air
temperature +40°C.
• The surface on which the system is installed must be
level and stable. It should not exceed a maximum of 2%
deviation from evenness is recommended.
• A smooth wall is required when the system is to be wall
mounted. The bench or wall surface must be strong
enough to hold the system (for system weight, refer to
the section Technical Specifications).
• An atmospherically floor drain with an outside diameter of
63 mm or 2.48 inch (DN 50 tube) shall be provided.
• Unobstructed draining of the rinsing water to the drain
must be ensured. When no floor drain is available, install
a water watcher to protect against water damage
(available only for Europe).
• A check valve is recommended in the feed-water line to
prevent back flow of feed-water from the water system.
• An electric socket with protective connection must be
available for connection of the system to the voltage
supply (refer to Electrical Connection table in the section
Technical Specifications). The electric socket must be
within 2 meters (6 feet) of the intended installation
location.
• Ample working space must be provided around the
system for easy and pleasant replacement of parts and
for ease of operation (refer to the section Technical
Specifications).
• Easy access for operation and control of the system.
Determine best layout of system to fit lab space. Place the
Smart2Pure Pro system, pretreatment and storage tank at
the desired location (on the workbench, under the
workbench, or wall mount).
Note: Refer Figure 9, Figure 13 and Figure 14 for system
layout setup.
Note: Pretreatment system, Smart2Pure Pro and storage
tank can be installed at different heights or under counter as
long as requirements as listed in “Installation Area” are
followed.
Note: The maximum tube distance between system and
storage tank should be 2 m / 78.7 inch. The minimum tube
distance between system and storage tank should be 0.5 m /
20 inch.
Mount Pretreatment to wall (refer to Pretreatment System
manual for mounting instructions). If not wall mounting
pretreatment, skip to next section.
Wall Mounting the
Smart2Pure Pro
Detailed instructions and needed hardware for mounting the
bracket on the wall are provided with the Wall Mounting Kit.
The kit adapts to the typical stud spacing of 16 inch.
1. Attach the 2 mounting BRACKETS to the back plate of
the Smart2Pure Pro system, using the (4x) M8 x 25 mm
long screws and 10 mm tall spacers (included in the kit).
Attach as shown in the Figure 4).
CAUTION: Free gravity flow to drain must be
ensured.
CAUTION: The wall mounting fixture (Item No.
50157885) supplied with the complete system or
purchased separately as an accessory.Before
mounting the system on the wall, verify the
strength of the wall to ensure that it is suitable for
supporting the system (refer to the section
Technical Specifications).
CAUTION: The screws and anchors supplied with
the wall mounting brackets are only suitable for
attaching the wall mounted bracket to a 16 inch
wooden stud construction, concrete, or solid
masonry wall.

Smart2Pure Pro Ultrapure water system The Installation Area | 15
Figure 4. Smart2Pure Pro wall mount bars
2. Using (4x) included 5/16” lag bolts and washers, attach
the wall mount bracket on the wall where you want to
mount your Smart2Pure Pro system.
3. Lift the system (2 people recommended) and hang it on
the wall mounting bracket.
The spring loaded pin locks itself on the bottom lip of
mounting bracket to prevent tipping.
Figure 5. Smart2Pure Pro wall mount bracket
4. To remove the unit from the wall, pull on both cords at the
bottom of the mounting brackets (refer to Figure 4), and
lift (2 people recommended) the unit slightly and pull
away from wall bracket.
Attaching the Wall
Mounting Bracket for 30 L
or 60 L Pure Water Tank
Note:
• Wall mounting hardware for the 30 L or 60 L pure water
tanks (purchased separately).
• 30 L pure water tank wall mounting bracket,
Item No.: 06.5015
• 60 L pure water tank wall mounting bracket,
Item No.: 06.5016
• The wall on which the pure water tank is to be installed or
mounted must have an adequate load-carrying capacity
(check the capacity and stability of the wall. Refer to the
section Technical Specifications for weight and
dimensions for pure water tanks).
(4x) Included M8 x 25 mm
Side View of
Release
(2x) Device Mounted Bracket
Hook
Cord
(4x) included
Back Plate
Smart2Pure Pro
long screws
Down
(floor)
10 mm Spacer
Wall Mounted Bracket
(4x) Mounting Holes for attaching 16” spaced wooden studs
CAUTION: Always lift and carry the system in
tandem (two people), never alone, to avoid any
risk of injury.
Lift the system at the two bottom corners.
Release Cord
Hook
(2x) Device Mounted Brackets
Spring loaded
pin lock
Mounted
Bracket
Wall