Thermo Sphere SCP-W Manual

SCP-W SCP-BINSTRUCTION GUIDE
CONTROL | TOUCH
SINGLE PROGRAMMABLE
Live well...

2
Contents
Compatibility ..............................................................
What's in the box? .....................................................
Before you start ..........................................................
Installing your thermostat ...........................................
Wiring diagram ...........................................................
User interface .............................................................
Heating modes ...........................................................
Set the time and date .................................................
Heating schedule ........................................................
Energy saving features ...............................................
Advanced settings ......................................................
Factory reset & key lock ..............................................
Technical data ...........................................................
Troubleshooting guide ..............................................
3
4
5
6
10
14
15
17
18
20
21
24
25
26

3
Compatibility
Sensor probes
This thermostat is compatible with ThermoSphere
NTC 10kΩ@ 25°C oor sensor probes.
Heating systems
This thermostat is compatible with all ThermoSphere
electric underoor heating systems
Replacing an existing thermostat?
Contact the manufacturer's technical department
and ask for the rating of the oor sensor at 25°C.

4
What’s in the box?
Check you've got everything:
• Programmable thermostat
• Floor sensor probe (3m)
• Floor sensor conduit (2m)
• Fixing screws
• Installation guide and warranty information
• Portrait mounting plate
You will also need:
• Electrical screwdriver
• Deep electrical back box
• Electrical test meter

5
Before you start
Your thermostat should be:
• Installed at least 1.2m from the oor
• On an internal wall
• Outside any wet zones (IP30)
• Installed on an RCD protected circuit
• Away from any hot or cold inuences
• Installed so that the oor sensor probe can be laid in a
heated area of the oor
• Installed by a professional, in line with current
electrical regulations and relevant local standards

6
Installing your thermostat
1. Switch off mains power
You will be installing your thermostat as
part of a high voltage mains electrical
circuit. To ensure your safety and to
protect the thermostat, switch off the
mains power and remove fuse from the
spur before you start the installation.
Fuse Box Fused Switch
CAUTION
High Voltage
Cables
OFF
ON ON ON ON ON
OFF
!

7
Installing your thermostat
2. Installation location
At this stage it its likely that an RCD protected
electric underoor heating system has been
installed and a back box is already in place.
The underoor heating cold tail should be pulled
up through the back box, and the sensor probe
installed (in the conduit provided) within the wall
cavity or pre chased channel in a solid wall.

8
3. Maximum distances
Your thermostat can be installed up to 50m away from the
underoor heating system it is controlling, provided that the
oor sensor is used to control the temperature.
Underoor heating cold tails and oor sensor probes can be
extended up to 50m.
Connect multiple heaters in parallel.
50m max.
Installing your thermostat

9
4. Un-clipping the mounting plate
Installing your thermostat
Lay thermostat screen side
down on a at surface
Release the mounting plate
form the clips
Carefully un-clip the white
ribbon cable
Press the white clip down
with a at screwdriver
Push the mounting plate
towards you
Use your phone camera
to watch the video

10
Installing your thermostat
230/240V AC Supply Live
230/240V AC Supply Neutral
UFH Neutral (Load N)
UFH Live (Load L)
Earth (Ground)
Sensor connections
(No polarity)
5. Wiring diagram
Connect the Thermostat to the underoor
heating (UFH) cold tail, power supply and oor
temperature sensor.
The oor temperature sensor is not polarity sensitive.
7654321

11
Installing your thermostat
6. Fix mounting plate in position
Use a cross-head screwdriver to x the mounting plate to the
back box in the wall. Now you can connect the white ribbon
cable to the fascia.

12
Installing your thermostat
7. Fix thermostat fascia in place
Locate the thermostat onto the mounting plate and
push down to clip in place.

13
Do not switch your underoor heating on
unless the entire heating cable, cold tail
joint and end termination are fully encased
in tile adhesive.
It is important that all adhesives and
grouting are dry and fully cured before you
switch on your underoor heating.
Most adhesives take between 7 to 10 days to cure. Follow
manufacturer guidelines.
The temperature of your underoor heating should be
increased gradually to avoid thermal shock in the oor. Start at
15°C and work up to your desired temperature 2-3°C per day.
Observe any maximum temperature guidelines from your oor
manufacturer.
Wait for
7 - 10 Days
before you
switch on
!
Switching on for the rst time

14
User interface
1
2
311
12
13
10
4
5
7 86 9
1. Day indicators
2. Time
3. Measured temperature
4. Heating on icon
5. Lock icon
6. Mode button
7. Up arrow
8. Down arrow
9. Power button
10. Event icons
11. Set temperature
12. Manual mode icon
13. Schedule mode icon

15
Heating modes
When your thermostat is on you can tap to switch
between Manual and Schedule heating modes.
Manual mode
Your thermostat will simply maintain the temperature you set
manually until you ask it to do something else!
Schedule mode
Your thermostat will follow a heating schedule that you can set up.

16
Temperature override
When the thermostat is in Schedule mode, running your heating timer
settings, it is possible to manually override the temperature without
adjusting the schedule or switching to manual mode.
You can adjust the temperature with the and arrows.
If you override the temperature while the thermostat is running the
heating schedule, the new override temperature will be maintained
until the next scheduled temperature change.
The thermostat will then revert to the preset heating schedule.
Temperature override

17
Setup
Setting the day and time
Switch the unit off by pressing .
Press and hold for 7 seconds until the time
begins to ash.
Use and to select the correct minute.
Press to switch to hours and use and to
select the correct hour.
Press again to edit the day and use and to
select the correct day. 1 = Monday & 7 = Sunday.
Press to save your settings.
NOTE: The thermostat will switch off after 30 seconds of
inactivity and any unsaved settings may be lost

18
Set up your heating schedule
*Check with your oor nish manufacturer for recommended maximum temperatures
1. Turn the thermostat on by pressing .
1. Press to switch to mode before you start.
2. Press to switch the unit off.
3. Press and hold for 7 seconds to edit your schedule. If
you have already set the clock press x3 to skip it.
4. Use and to adjust the start time for event 1 and
press to save. Now use and to select the desired
Comfort (or “On”) temperature between 20 - 28°C
depending on your oor nish*.
5. Press to advance to event 2 and use and to select
the desired time to switch to a lower temperature.
6. Press to save. Now use and to select the desired
Eco (or “Off”) temperature between 16 - 20°C.
7. Press to advance to event 3 and use and to select
the desired time to switch to a higher temperature.
Event 1
Wake Up
Event 2
Out
Event 3
Home

19
Set up your heating schedule
8. Press to save. Now use and to select the desired
Comfort (or “On”) temperature between 20 - 28°C.
9. Press to advance to event 4 and use and to select
the desired time to switch to a lower temperature.
10. Press to save. Now use and to select the desired
Eco (or “Off”) temperature between 16 - 20°C.
11. Press to advance to event 5 and use and to select
the desired time to switch to a higher temperature.
12. Press to save. Now use and to select the desired
Comfort (or “On”) temperature between 20 - 28°C.
13. Press to advance to event 6 and use and to select
the desired time to switch to a lower temperature.
14. Press to save. Now use and to select the desired
Eco (or “Off”) temperature between 16 - 20°C.
15. Press to activate your schedule and you’re done!
Event 4
Out
Event 5
Home
Event 6
Sleep
Don‘t want to use all of the available heating events? You can
skip events by setting the same temperature as the previous event

20
Energy saving features
Adaptive Start
With the Adaptive Start feature enabled your thermostat will measure
how long it takes for your individual oor to heat up and ensure the target
temperature is achieved at the set time.
So if you set your heating schedule to 24°C at 07:00, the oor will be at
24°C at 07:00. No need to set the heating to come on early!
your thermostat starts learning from the rst time you enable the heating
schedule. It turns on an hour early to start with and gradually optimises the
heat up time over 7 days.
Open Window Detector
When the Open Window Detection feature is enabled your thermostat can
detect sudden drops in temperature and will switch off your heating to
eliminate wasted energy.
Your thermostat will come back on after 30 minutes, provided the
temperature has stabilised.
You can activate and adjust these features in the advanced settings
menu. See page 21 - 23.