Third Millennium OC1 User manual

ISSUE - A : new format and layout - JUNE 2021

ISSUE - B : amendments to bring in line with new’ format and layout - forum meeting 18/08/2021 + decisions forum 01/09/2021 & 08/09/2021

Third Millennium Systems Ltd. 18 / 19 Torfaen Business CentrePanteg Way New Inn PONTYPOOL NP4 0LS United Kingdom tel: +44 (0) 1495 751 992 web: www.tm-readers.com contact: [email protected]

‘MIFARE’, ‘MIFARE Classic’ and ‘MIFARE DESFire’ are trademarks of NXP B. .

All copyrights © and trademarks ® / ™ are acknowledged and remain the property of their respective owners.

Scan the QR code or visit the address below to find a list of datasheets to all products and other support information.https://www.tm-readers.com/downloads.htm Key features•OSDP Secure communication•Use existing cabling•Easy access (with SECURE AREA)•Communicates with -Third Millennium OSDP readers•UK design and manufacture•Matt black finish•Slim profile•RGB LED•1 year limited warrantyThe OC1 is not an RFID card reader. The unit, plus a Third Millennium OSDP reader, makes use of existing reader cabling, which minimises installation cost and cosmetic damage, and will eliminate the security vulnerability of the traditional Wiegand interface between an access control reader, and the control panel.44mm (1.7 inches)

72mm (2.8 inches)

25mm(1.0 inch) MODEL CurrentmAVoltageVdcWiegandClock & DataUL294 OC1 35(without reader)10 - 16••

P A R T N E R

Registered PartnerMechanical

Dimensions 72 x 44 x 25 mm (2.8 x 1.7 x 1.0 inches)

Housing Moulded polycarbonate

Fixing 4mm., max’ diameter

Environmental

Operating temp’ 0°C to +49°C

Humidity 85±5% at 30±2°C (86±3°F)

Ingress Suitable for INDOOR USE only

(ensure you locate and position the OC1 in a SECURE area)

Electrical

Voltage see table below

Current see table below

Data Voltage Rest >4Vdc / Active <1Vdc

Data output see table below

Indication 1 RGB LED

Sounder NONE

Termination screw terminal connection block

Reader Models are sold as customer-specific configurations.Please call +44 (0) 1495 751 992 to discuss your custom configuration or LEGIC® reader requirements.OverviewThe OC1 advanced access control interface provides an OSDP Secure communications link to a compatible Third Millennium OSDP reader.Mounted close to the control panel, the OC1 provides a compatible Wiegand output to allow the security of an access control system to be upgraded cost effectively.The integrated RGB LED provides a visual indication of the state of the link between the OC1 unit and the reader.+49

1yr

ISSUE - A : new format and layout - JUNE 2021

ISSUE - B : amendments to bring in line with new’ format and layout - forum meeting 18/08/2021 + decisions forum 01/09/2021 & 08/09/2021

Third Millennium Systems Ltd. 18 / 19 Torfaen Business CentrePanteg Way New Inn PONTYPOOL NP4 0LS United Kingdom tel: +44 (0) 1495 751 992 web: www.tm-readers.com contact: [email protected]

‘MIFARE’, ‘MIFARE Classic’ and ‘MIFARE DESFire’ are trademarks of NXP B. .

All copyrights © and trademarks ® / ™ are acknowledged and remain the property of their respective owners.

EASY ACCESS Slide the front cover verticallyas shown below.Once disengaged, pull the frontcover away from the base.Safely set aside the front coverfor reuse. . CONNECTION Make wire connections to the terminal blocks in accordance with the diagram and pin-outs shown below.NOTE: If using more than one OC1 converter, you may wish to fix cable markers to each unit to identify the reader to which it is linked. .

existing

WIEGAND

access control

panel

existing

WIEGAND

access control

panel

to reader

- 1

- 2

- 3

- 4

- 5

- 6

- 7

- 8

+Vdc IN

DATA1/CLK

DATA0/DATA

GREEN

RED

Buzze

TMPR

4 - RS485+

3 - RS485-

2 - +Vdc OUT

1 - 0V

OSDP

reader #1

INSTALLATION When installing, ensure the OC1 (OSDP CONVERTER) is positioned in a SECURE AREA adjacent to your access control panel.Secure OSDP communication is between a Third Millennium OSDP reader and the OC1 unit, using existing cabling, and eliminating the security vulnerability of the traditional Wiegand interface. .Secure

existing

WIEGAND

access control

panel

Wiegand output

OSDP CONVERTER

OSDP converter

to be located

adjacent to your

access control

panel in a

SECURE AREA