thomann Millenium MPS-400 User manual

MPS-400
e-drum set
assembly instructions

Musikhaus Thomann e.K.
Treppendorf 30
96138 Burgebrach
Germany
Telephone: [phone]
E-mail: [email protected]
Internet: www.thomann.de
15.05.2012

Table of contents
1 Safety instructions.......................................................................................................................................................................................................... 4
2 Contents of package....................................................................................................................................................................................................... 5
3 Assembly.............................................................................................................................................................................................................................. 6
4 Protecting the environment.................................................................................................................................................................................... 13
Table of contents
MPS-400
3

1 Safety instructions
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children.
Choking hazard!
Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and
choke!
Never let children unattended use electrical devices.
Safety instructions
e-drum set
4

2 Contents of package
Before you assemble your kit, make sure the contents of package is complete according to the following illustrations.
Millenium MPS-400 e-drum stereo set
nMillenium e-drum module
nPads:
1 × snare / stereo
3 × tom / mono
1 × bass drum
2 × cymbals / stereo
1 × hi-hat
nHi-hat controller
nDrum pedal
nRack with pad brackets
nComplete pad wiring
nMains adapter
Millenium MPS-400 e-drum hi-hat MINE set
nMillenium e-drum module
nPads:
1 × snare / stereo
3 × tom / mono
1 × bass drum
2 × cymbals / stereo
1 × hi-hat
nHi-hat controller Millenium MINE V2.0
nStage hi-hat Millenium DHS 1018
nDrum pedal
nRack with pad brackets
nComplete pad wiring
nMains adapter
Contents of package
MPS-400
5

3 Assembly
Assembling the rack
CAUTION!
Danger of cuts on hands and fingers
When plugging the connections, take care for sharp edges on the metal pipes, screws etc.
Loosen the screws of each terminal before inserting the pipes. Mount the various elements in the specified sequence. The posi‐
tions of the pads, cymbals, etc. are shown in the illustration below.
Assembly
e-drum set
6

Connect the left side pipe (mainstay L) to the left base and tighten the allen screw with the supplied drum key. Stabilise the unit
with a crossbar (see figure). Then connect the right side pipe (mainstay R) to the right base and tighten the allen screw with the
supplied drum key. Stabilise the unit with a crossbar (see figure).
Connect the upper two clamps of the left and right mainstay using both crossbars of the rack and tighten the allen screws of the
clamps using the supplied drum key (see figure).
Assembly
MPS-400
7

Connect the upper left side arm (L1) to the second clamp. Connect the lower left side arm (L2) to the third clamp of the left main‐
stay. Tighten the allen screw of the clamps firmly using the supplied drum key. Then connect the right side arm (R) to the second
clamp of the right mainstay and tighten the allen screw of the clamp firmly using the supplied drum key.
Assembly
e-drum set
8

Mounting pads on the rack
Attach the supplied L-pieces to the pads. First, tighten the wing nuts on the pads by hand. Then slide the plastic ends of the L-
pieces up to the stop into the designated terminals on the rack (see figure). Align the pads on the rack to meet your needs, then
tighten the wing nuts of the pad brackets and the bolts of the pad terminals on the rack firmly and evenly.
Mounting cymbals on the rack
Assembly
MPS-400
9

Put the cymbal holders into the designated terminals on the rack (see figure) and tighten the allen screws of the terminals with
the supplied drum key firmly.
Unscrew the wing nuts from the cymbal holders and take the felt washers off the holders. Place the cymbals as shown in the
figure on the holders. Then place the felt washers on the cymbals and tighten the cymbals with the associated wing nuts on the
holders.
Mounting the drum module on the rack
Attach the supplied L-piece to the drum module. Tighten the wing screw of the module hand-tight first. Then slide the plastic end
of the L-piece up to the stop into the designated terminal on the left side arm of the rack (see figure). Align the module on the
rack according to your needs and tighten the wing nut on the module as well as the screw of the pad clamp on the rack firmly
and evenly.
Assembly
e-drum set
10