thomann Ignition 2bright Pint FC150 IP User manual

2Bright Expo 575 TW
LED Spotlight
User Manual

Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: [phone]
Internet: www.thomann.de
14.09.2022, ID: 542637

Table of contents
1 General information................................................................................................................................. 4
1.1 Further information........................................................................................................................... 5
1.2 Notational conventions.................................................................................................................... 5
1.3 Symbols and signal words............................................................................................................... 6
2 Safety instructions..................................................................................................................................... 8
3 Features....................................................................................................................................................... 12
4 Installation.................................................................................................................................................. 13
5 Starting up.................................................................................................................................................. 16
6 Connections and controls................................................................................................................... 18
7 Operating.................................................................................................................................................... 20
7.1 Main menu.......................................................................................................................................... 20
7.2 Menu overview................................................................................................................................. 25
7.3 Functions in DMX mode................................................................................................................ 26
8 Technical specications....................................................................................................................... 27
9 Plug and connection assignments.................................................................................................. 30
10 Troubleshooting...................................................................................................................................... 31
11 Cleaning....................................................................................................................................................... 33
12 Protecting the environment.............................................................................................................. 34
Table of contents
2Bright Expo 575 TW 3
LED Spotlight

1 General information
This user manual contains important information on the safe operation of the device. Read and
follow all safety notes and all instructions. Save this manual for future reference. Make sure
that it is available to all persons using this device. If you sell the device to another user, be sure
that they also receive this manual.
Our products and user manuals are subject to a process of continuous development. We there‐
fore reserve the right to make changes without notice. Please refer to the latest version of the
user manual which is ready for download under www.thomann.de.
General information
42Bright Expo 575 TW
LED Spotlight

1.1 Further information
On our website (www.thomann.de) you will nd lots of further information and details on the
following points:
Download This manual is also available as PDF le for you to download.
Keyword search Use the search function in the electronic version to nd the topics of
interest for you quickly.
Online guides Our online guides provide detailed information on technical basics
and terms.
Personal consultation For personal consultation please contact our technical hotline.
Service If you have any problems with the device the customer service will
gladly assist you.
1.2 Notational conventions
This manual uses the following notational conventions:
General information
2Bright Expo 575 TW 5
LED Spotlight

The letterings for connectors and controls are marked by square brackets and italics.
Examples: [VOLUME] control, [Mono] button.
Texts and values displayed on the device are marked by quotation marks and italics.
Examples: ‘24ch’ , ‘OFF’ .
1.3 Symbols and signal words
In this section you will nd an overview of the meaning of symbols and signal words that are
used in this manual.
Signal word Meaning
DANGER! This combination of symbol and signal word indicates an
immediate dangerous situation that will result in death or
serious injury if it is not avoided.
WARNING! This combination of symbol and signal word indicates a pos‐
sible dangerous situation that can result in death or serious
injury if it is not avoided.
NOTICE! This combination of symbol and signal word indicates a pos‐
sible dangerous situation that can result in material and
environmental damage if it is not avoided.
Letterings
Displays
General information
62Bright Expo 575 TW
LED Spotlight

Warning signs Type of danger
Warning – high-voltage.
Warning – dangerous optical radiation.
Warning – suspended load.
Warning – danger zone.
General information
2Bright Expo 575 TW 7
LED Spotlight

2 Safety instructions
This device is intended for use as an electronic lighting eect by means of LED technology. The
device is designed for professional use only and is not suitable for use in households. Use the
device only as described in this user manual. Any other use or use under other operating con‐
ditions is considered to be improper and may result in personal injury or property damage. No
liability will be assumed for damages resulting from improper use.
This device may be used only by persons with sucient physical, sensorial, and intellectual
abilities and having corresponding knowledge and experience. Other persons may use this
device only if they are supervised or instructed by a person who is responsible for their safety.
Extend the operating life of the device by regular breaks and by avoiding frequent
switching on and o. The device is not suitable for continuous operation.
Safety
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking
hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and
choke! Never let children unattended use electrical devices.
Intended use
Safety instructions
82Bright Expo 575 TW
LED Spotlight

DANGER!
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts
inside. Do not use the device if covers, protectors or optical components are missing or damaged.
DANGER!
Electric shock caused by short-circuit
Always use proper ready-made insulated mains cabling (power cord) with a protective contact plug. Do not modify the mains cable
or the plug. Failure to do so could result in electric shock/death or re. If in doubt, seek advice from a registered electrician.
WARNING!
Risk of injury caused by falling objects
Make sure that the installation complies with the standards and rules that apply in your country. Always secure the device with a
secondary safety attachment, such as a safety cable or a safety chain.
WARNING!
Eye damage caused by high light intensity
Never look directly into the light source.
WARNING!
Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive persons should avoid looking at strobe lights.
NOTICE!
Risk of re
Do not block areas of ventilation. Do not install the device near any direct heat source. Keep the device away from naked ames.
Safety instructions
2Bright Expo 575 TW 9
LED Spotlight

NOTICE!
Risk of re and overheating
The use with closed barn doors can cause re or overheating in the spotlight. The lifetime of the LEDs will be reduced when using
the device with closed barn doors. Otherwise, the integrated thermostat causes a thermically reasonable shutdown. Use the device
only with open barn doors.
NOTICE!
Risk of overheating
The distance between light output and the illuminated surface must be more than 1.5 m (19.7in). Provide sucient ventilation. The
ambient temperature must always be below 104 °F (40 °C).
NOTICE!
Risk of re
The optical lenses of the device focus the light and can cause a burning glass eect when exposed to sunlight. Never expose unas‐
sembled lenses to direct sunlight.
NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never expose the device to any liquid or moisture. Avoid
direct sunlight, heavy dirt, and strong vibrations. Only operate the device within the ambient conditions specied in the chapter
‘Technical specications’ of this user manual. Avoid heavy temperature uctuations and do not switch the device on immediately
after it was exposed to temperature uctuations (for example after transport at low outside temperatures). Dust and dirt inside can
damage the unit. When operated in harmful ambient conditions (dust, smoke, nicotine, fog, etc.), the unit should be maintained by
qualied service personnel at regular intervals to prevent overheating and other malfunction.
Safety instructions
10 2Bright Expo 575 TW
LED Spotlight

NOTICE!
Power supply
Before connecting the device, ensure that the input voltage (AC outlet) matches the voltage rating of the device and that the AC
outlet is protected by a residual current circuit breaker. Failure to do so could result in damage to the device and possibly injure the
user. Unplug the device before electrical storms occur and when it is unused for long periods of time to reduce the risk of electric
shock or re.
NOTICE!
Fire hazard due to exceedance of the maximum current
The device can power other devices of identical construction. The current consumption of all other devices connected in series must
not exceed the values indicated in the technical specications. Otherwise you risk injuries and irreparable damages to the device.
Only connect so many identical devices that the maximum current consumption is not exceeded. Ensure the sucient dimensioning
(wire cross section) of the power cables used for all devices connected in series.
Safety instructions
2Bright Expo 575 TW 11
LED Spotlight

3 Features
Powerful and exible LED spotlight for showrooms, studios, exhibition booths, etc.
n31 white light LEDs
nReplacement for 575 W daylight lamps
nControl via DMX (3 channels) as well as via buttons and display on the unit
nLockable connections (Power Twist) for self-supply and to supply further devices
nSturdy bracket for secure attachment to trusses or rm footing on the ground
nIncludes safety cable, barn doors, diuser and colour lter frame
nOptional accessories
– 2Bright Expo 575 15° Lens Kit (item no. 542635)
– 2Bright Expo 575 35° Lens Kit (item no. 542636)
nSpare parts
– 2Bright Expo 575 Barndoor (item no. 543174)
– 2Bright Expo 575 Diusor (item no. 543176)
For technological reasons, the light output of LEDs decreases over their lifetime. This eect
increases with higher operating temperature. You can extend the service life of the illuminants
by providing adequate ventilation and operating the LEDs with the lowest possible brightness.
Features
12 2Bright Expo 575 TW
LED Spotlight

4 Installation
Unpack and check carefully there is no transportation damage before using the unit. Keep the
equipment packaging. To fully protect the product against vibration, dust and moisture during
transportation or storage use the original packaging or your own packaging material suitable
for transport or storage, respectively.
WARNING!
Risk of injury caused by falling objects
Make sure that the installation complies with the standards and rules that apply
in your country. Always secure the device with a secondary safety attachment,
such as a safety cable or a safety chain.
NOTICE!
Risk of overheating
The distance between light output and the illuminated surface must be more
than 1.5 m (19.7in).
Provide sucient ventilation.
The ambient temperature must always be below 40 °C (104 °F).
Installation
2Bright Expo 575 TW 13
LED Spotlight

NOTICE!
Use of stands
When mounting the device onto a stand, ensure that the stand is in a safe and
stable position and that the weight of the device does not exceed the maximum
permissible load capacity of the stand.
NOTICE!
Possible data transmission errors
For error-free operation make use of dedicated DMX cables and do not use ordi‐
nary microphone cables.
Never connect the DMX input or output to audio devices such as mixers or ampli‐
ers.
You can install the unit in hanging or standing position. When in use, the device must always
be attached to a solid surface or an approved truss. Use the openings provided on the two-
piece bracket for attaching.
Always work from a stable platform whenever installing, moving or servicing the unit. In doing
so, the area underneath the unit must be cordoned o.
The safety cable must be attached to the safety cable eyelet on the back of the device.
Mounting options
Installation
14 2Bright Expo 575 TW
LED Spotlight

Please note that this device must not be connected to a dimmer.
Installation
2Bright Expo 575 TW 15
LED Spotlight

5 Starting up
Create all connections while the device is o. Use the shortest possible high-quality cables for
all connections. Take care when running the cables to prevent tripping hazards.
Connect the DMX input of the device to the DMX output of a DMX controller or another DMX
device. Connect the output of the rst DMX device to the input of the second one, and so on
to form a daisy chain. Always ensure that the output of the last DMX device in the daisy chain
is terminated with a resistor (110 Ω, ¼W).
Connections in DMX mode
Starting up
16 2Bright Expo 575 TW
LED Spotlight

When you congure a group of devices in master/slave mode, the rst unit will control the
other units for an automatic, sound-activated, synchronized show. This function is ideal when
you want to start a show immediately. Connect the DMX output of the master device to the
DMX input of the rst slave device. Then connect the DMX output of the rst slave device to
the DMX input of the second slave device and so on.
Connect the device to the power supply to start operation.
Connections in master/slave
mode
Starting up
2Bright Expo 575 TW 17
LED Spotlight

6 Connections and controls
MENU UP DOWN ENTER
2bright Expo 575 TW
100-240V~50/60Hz
$
&
'
%
(
#
Connections and controls
18 2Bright Expo 575 TW
LED Spotlight

1[DMX In] | DMX input, designed as XLR panel plug, 3-pin
2[DMX Out] | DMX output, designed as XLR panel socket, 3-pin
3 Display and control buttons
[MENU] | activates the main menu and toggles between menu items. Closes an opened submenu.
[UP] | increases the displayed value by one.
[DOWN] | decreases the displayed value by one.
[ENTER] | selects an option of the respective operating mode.
4[F3AL250V] | fuse holder
5 Safety cable eyelet
6[Power In] | lockable input socket (Power Twist) for the power supply of the device
7[Power Out] | lockable output socket (Power Twist) for powering a connected device
Connections and controls
2Bright Expo 575 TW 19
LED Spotlight

7 Operating
7.1 Main menu
1. Press [MENU] to activate the main menu.
2. Use [UP] or [DOWN] to select the desired parameter or to change the respectively dis‐
played value.
3. When the display shows the desired parameter or value press [ENTER] to enter the
respective submenu or to conrm a new value.
4. To return to the previous menu level without changes, press [MENU].
1. Press [MENU] to activate the main menu.
2. Use [UP] or [DOWN] until the display shows ‘Address’ and conrm with [ENTER].
3. Use [UP] or [DOWN] to select a value between ‘Add: 001’ and ‘Add: 512’ to set the
desired DMX address and conrm with [ENTER].
Make sure that this number matches the conguration of your DMX controller. This set‐
ting is only relevant when the device is controlled via DMX.
4. To return to the previous menu level without changes, press [MENU].
DMX address
Operating
20 2Bright Expo 575 TW
LED Spotlight