Thomas&Betts WTID400 User manual

O
M
L
N
R
S
T
U
V
W
X
Y
Z
–
·
2
3
4
5
6
7
8
9
A
K
J
I
H
G
C
E
F
B
D
Operating Instructions
For SS Tape Embosser WTID400
• Replacement rolls of SS ID tape: Part # WTID405 -1/2” wide X .005” thick X 21’ long
• Reverse Image wheel included for special projects requiring mirror script labels.
The Thomas & Betts WTID400 stainless steel tape embossing tool is ideal for identifying electrical cable runs, valves,
motors, switches, and anything else needing the durability of stainless steel identification. Choose either to hole-punch
for hang tags or cut and form cable tie slots for additional strength and security. The 1/2" wide SS tape embossed with
3/16" inch characters provides a corrosion resistant, easy-to-read, quick to install, identification tag you can make on
the spot.
A - Character Wheel
B - Character Viewing Window
C - Hole Punch Slot
D - Tag Centering Guide
E - Tape Exit
F - Tie Forming Slot
G - Start Line
H - Cut Off Handle
I - Tape Advance Knob
J - Tape Cassette Door
K - Embossing Handle
L - Tape Waste Exit (located on the bottom)
M - Depth Adjustment Knob
N - Release Lever
O - Rollers
TA04624 A
Page 1 of 2

WARRANTY: Thomas & Betts sells this product with the understanding that the user will perform all necessary tests to determine the suitability of this product
for the user's intended application. Thomas & Betts warrants that this product will be free from defects in materials and workmanship for the period stated on
the enclosed warranty card. Upon prompt notification of any warranted defect, Thomas & Betts will, at its option, repair or replace the defective product or
refund the purchase price. Proof of purchase is required. Misuse or unauthorized modification of the product voids all warranties.
Limitations and Exclusions: THE ABOVE WARRANTY IS THE SOLE WARRANTY CONCERNING THIS PRODUCT, AND IS IN LIEU OF ALL OTHER
WARRANTIES EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, WHICH ARE SPECIFICALLY DISCLAIMED. LIABILITY FOR BREACH OF THE ABOVE WARRANTY IS LIMITED TO COST OF
REPAIR OR REPLACEMENT OF THE PRODUCT, AND UNDER NO CIRCUMSTANCES WILL THOMAS & BETTS BE LIABLE FOR ANY INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
1) The tape must be flat and free of kinks and burrs on the leading
edge.
2) Check that the embossed characters on the tape are not set so
deep that the tape appears wrinkled at the top and bottom edges.
3) When the hole punch is used, the punched hole must be clean and
free of excessive burrs.
4) Before withdrawing the tape backward beyond the front edge of
the cutter, ensure that the front edge of the tape is flat and free of
burrs.
5) After withdrawing the tape backward, take up the slack of the tape
below the hands by winding excessive tape into the holder before
further usage.
6) If tape is slipping, clean the rollers (O) using a soft cloth and
alcohol while turning the rollers several revolutions.
7) Regularly check for cut SS tape scrap build up in the bottom of
the tool (L).
Punching holes and slots in your ID Tag
1) Insert one end of the tag in the appropriate slot on the front of the
tool. The slots are marked appropriately.
2) IMPORTANT:
a. The letters must face down for proper positioning of cable tie slot.
b. Plan enough space for slot to be clear of letters and punched
holes.
3) Lift the cut-off handle (H) and perform the punch operation easily.
The tool is capable of punching holes (C), cable tie slots (F) or both.
Centering the Text on the ID Tag
1) After cutting the previous label, emboss your next label.
2) Pull the tag centering guide (D) forward from its normally retracted
position.
3) Advance the tape until the last character is even with the letter "L"
on the tag centering guide.
4) Cut off the tag, the tag should be centered.
5) To center the tag with a short lead, first retract the tag until tape
edge is at the start line. Emboss the next label; advance the tape
until the last character is even with the letter "S" on the tag
centering guide (D).
6) Cut off the tag which is now centered.
The tool is equipped with a retractable tag centering guide (D) to
allow a short or long lead.
Retracting the SS Tape
1) While pulling back the Release Lever (N), turn the Tape Advance
Knob (I) counter-clockwise.
The SS tape may have been advanced too far or you may need to
re-center the label.
Cutting the Tape & Label
1) Advance the tag forward far enough to clear the embossed
lettering or see the directions for Centering.
2) Lift the cutter handle up and forward to cleanly cut the band.
This tool is equipped with a heavy duty cutter bar (H) which will
cut SS tags to length.
Adjusting the Depth of Characters
1) This adjustment may be used to optimize the clarity of the
characters on the tape. Determine the best setting by turning the
adjustment knob (M) towards the + or -symbol.
IMPORTANT: An impression which is too deep may cause the SS
tape to wrinkle between the characters and may jam in the tool.
Embossing your SS Tape
1) Turn the character wheel (A) until the desired letter is centered in
the character viewing window (B).
2) Squeeze the embossing handle (K) firmly, one time. Release the
embossing handle fully before selecting the next character. Each
time the handle is squeezed the SS tape will advance one space.
3) Add a space between words or numbers by squeezing the handle
gently 1/2 way and releasing the handle. Also, a space can be
added by releasing the handle completely and turning the SS tape
advance knob one click in a clockwise direction.
IMPORTANT: Avoid squeezing the handle while turning the character
wheel!
Loading Tape
1) Place the tool in front of you on a flat surface, open the SS tape
door (J) and remove any remaining pieces of SS tape in the
storage cavity or in between the tape feed rollers (O) .
2) Hold the next roll of SS tape securely and remove the strip of
plastic tape taking care not to allow the roll to unravel.
3) Place the roll of SS tape into the tape storage cavity (J) allowing
2-3" of material to extend from the tape slot and close the SS tape
door.
4) Feed the SS tape into the two rollers (O) and begin to squeeze the
handle (K) 1/2 way several times to advance the SS tape.
The WTID400 is presented with one roll of SS tape already installed
as part of our factory adjustment and testing. To refill, follow these
simple instructions:
1
2
3
4
5
6
7
Trouble Shooting
8
Operating Instructions
Thomas & Betts Corporation
Memphis, Tennessee
www.tnb.com
For Parts or Service, contact the
Thomas & Betts Tool Service
Center at 1-800-284-TOOL (8665).
© 2010 Thomas & Betts. All Rights Reserved.
TA04624 A
Page 2 of 2
WARNING
To ensure smooth operation and free movement of the tape:
The edges of the stainless steel tape may be sharp. Use
caution when removing tape from your tool or installing a new
roll of tape.
NOTE: Letters in bold correspond to the illustration on front
page.