Thomasville Nature's Retreat 12251-001 User manual

Page 1 of 2
Assembly Instructions Nature’s Retreat™Arm Chair Model # 12251-001/011/012
! KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE !
Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts that may have
come loose inside the carton during shipment. Please read all instructions carefully before starting the assembly process.
CAUTION: Some items and/or the components are cumbersome and heavy.Therefore, the assistance of one or more people
is recommended in order to prevent personal injury and insure that the item and/or its components are not damaged during
the assembly process. Perform all assembly steps on a flat, soft, non-abrasive surface. Do not overtighten the screws or bolts.
Parts & Hardware List
No. Diagram, Description, & Size (mm) Qty No. Diagram, Description, & Size (mm) Qty
Side Frame
862 x 757 x 46
Side Frame
862 x 757 x 46
Seat Frame
w/Logo Plate
723 x 600 x 46
Back Frame
620 x 513 x 24
Front Rail
660 x 60 x 24
Back Rail
620 x 60 x 24
HW-ST-01-046
F-Screw 7x90
HW-ST-18-001
Allen key 4x98
HW-MM-06-075
Adjustable Leveling Glide Ø22x27
HW-ST-01-069
Wood Screw 5x70
Additional Tools Required: #2 Phillips head screwdriver
1. Insert the front rail (E), back rail (F), and seat back
(D) into the mortise holes on the side rail (A) as
indicated in Figure 1.
Figure 1
NR_AI ArmChair_eng 8/22/07 12:08 AM Page 1

Page 2 of 2
Assembly Instructions Nature’s Retreat™Arm Chair Model # 12251-001/011/012
! KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE !
2. Place the side frame (B) on top of the front rail (E), back
rail (F), and seat back (D) so that the tenons on the
front & back rails and seat back are inserted in the
mortise holes on the inside of the seat frame. Attach
using the F-screws (G) and tighten with the Allen key
(H) as indicated in Figure 2.
Figure 2
3. Carefully turn the chair over into the upright position so
that the side frame (A) remains in place with the front &
back rails and seat back.Attach the side frame (A) using
the F-screws (G) and tighten with the Allen key (H) as
indicated in Figure 3.
Figure 3
5. Screw the adjustable leveling glides (J) into the bottom
of each leg as shown in Figure 5.
Check/Re-tighten screws.
Figure 5
4. Install the seat frame (C) on top of the front rail (E) and
back rail (F) so that the logo plate is at the back.
Position the seat frame (C) so that the seat frame front
and back rails are flush with the front rail (E) and back
rail (F).Attach the seat frame by inserting the wood
screws (I) through the bottom of the front and back
rails and into the pre-bored pilot holes in the seat
frame.Tighten using a # 2 Phillips head screw driver. See
Figure 4.
Figure 4
NR_AI ArmChair_eng 8/22/07 12:08 AM Page 2

Page 1 of 2
Assembly Instructions Nature’s Retreat™Bridge Model # 12251-001/011/012
! KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE !
Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts that may have
come loose inside the carton during shipment. Please read all instructions carefully before starting the assembly process.
CAUTION: Some items and/or the components are cumbersome and heavy.Therefore, the assistance of one or more people
is recommended in order to prevent personal injury and insure that the item and/or its components are not damaged during
the assembly process. Perform all assembly steps on a flat, soft, non-abrasive surface. Do not overtighten the screws or bolts.
Additional Tools Required:
1. #2 Phillips head screwdriver
2. Drill
3. 3/32" diameter drill bit
Note: A bottle of Espresso Touch-up
Oil (E) was provided for your
convenience. Do NOT discard. Use
when necessary to touch-up and repair
minor nicks, scratches and/or abrasions.
1. Align the holes in the Z-brackets with
the pre-bored holes in the bottom of
the bridge (A) and attach using the
wood screws (D). See Figure 1.
Figure 1
Parts & Hardware List
No. Diagram, Description, & Size (mm) Qty
Bridge
731 x 664 x 24
Nature’s Retreat
Arm Chair
864 x 829 x 752
HW-ST-04-139
Z-Bracket
47 x 25 x 27 x (t2.0)
HW-ST-01-008
Wood Screw 4x20
Espresso Touch-up Oil
NR_AI Bridge_eng 8/22/07 12:15 AM Page 1

Page 2 of 2
Assembly Instructions Nature’s Retreat™Bridge Model # 12251-001/011/012
! KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE !
2. Insert the bridge (A) between the two chairs (B) so that the notches at the back of the bridge fit around the back uprights
of the chair and the edges of the bridge are flush with the inside edges of the chair arms. Using a 3/32" diameter drill bit,
pre-bore a pilot hole through the holes in the Z-brackets into the underside of the chair arms.Attach the bridge to the
bottom of the chair arms using the wood screws (D) as indicated in Figure 2.
Figure 2
Figure 3
NR_AI Bridge_eng 8/22/07 12:15 AM Page 2