THOMSON RCA DCD407RH User manual

Satellite Receiver
User’s Guide
Changing Entertainment. Again.

Cautions
Do not stack electronic components or other objects on top of the
Digital Satellite Receiver. The slots on top of the receiver must be left
uncovered to allow proper airflow to the unit. Blocking the airflow to
the unit could impair performance or damage your receiver and other
components.
Remove any sales or promotional materials attached to the product.
Do not stack the digital satellite receiver on top of a “hot component”
such as an audio power amplifier.
FCC Regulations state that unauthorized changes or modifications to
this equipment may void the user’s authority to operate it.
Your system is equipped with a RF remote control. The RF remote
control complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: 1) The RF remote may not cause harmful
interference and; 2) The RF remote must accept any interference
received, including interference that may cause undesired operation.
Note to Cable TV Installer:
This reminder is provided to call your attention to article 820-40 of the
National Electrical Code (Section 54 of the Canadian Electrical Code, Part
1) which provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding
system of the building as close to the point of cable entry as practical.
Note to Satellite Dish Installer:
This reminder is provided to call your attention to articles 810 and 820
of the 1999 National Electrical Code. Refer to article 810, in particular
to 810-1 and 810-15, for required grounding of the metal structure of
the Dish Antenna. Refer also to the 810-2 which, by reference to article
820, requires that the satellite dish coaxial cable shield be connected to
the grounding system of the building as close to the point of cable
entry as practical.
Care and Cleaning:
Use a soft cloth or dusting attachment of your vacuum cleaner to dust
your digital satellite receiver. Remove dust from the ventilation holes on
the top and bottom.
Plastic surfaces are easily scratched and can be marred by alcohol and
various solvents. Avoid excessive use of oil-based furniture polishes
since the materials used in the cabinet will accumulate more dust. A
non-abrasive, anti-static cleaner/polisher is recommended.
Important Information
Product Registration
Please fill out the product registration card (packed separately) and
return it immediately, or register online at rca.com. Returning the card
allows us to contact you if needed.
Product Information
Keep your sales receipt to obtain warranty parts and service and for
proof of purchase. Attach it here and record the serial and model
numbers in case you need them. These numbers are located on the
product.
Model No. ______________________________________________
Serial No. _______________________________________________
Purchase Date: __________________________________________
Dealer/Address/Phone: ____________________________________
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for
long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
IMPORTANT NOTICE:
This device incorporates an anticopy process technology that is
protected by U.S. patents and other intellectual property rights. The
anticopy process is licensed for non-commercial, home use only.
Reverse engineering or disassembly is prohibited.
This symbol indicates "dangerous voltage" inside the product
that presents a risk of electric shock or personal injury.
WARNING
To reduce the risk of fire or electric shock, do not expose this product
to rain or moisture. The apparatus shall not be exposed to dripping or
splashing. No objects filled with liquids, such as vases, shall be placed
on the apparatus.
This symbol indicates important instructions accompanying
the product.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
Caution: To reduce the risk of electric
shock, do not remove cover (or back). No
user serviceable parts inside. Refer
servicing to qualified service personnel.

1
Table of Contents
Chapter 1: Connections & Setup
Things To Consider Before You Connect Components ................ 2
Choose Your Connection................................................................ 2
Insert Your Access Card ................................................................. 2
Jacks and Cables............................................................................. 2
Excellent Connection ..................................................................... 3
Very Good Connection ................................................................... 4
Basic Connection ............................................................................ 5
RF Remote Antenna Connection .................................................. 6
Satellite Receiver Rear Panel ........................................................ 6
Place Batteries in the Remote Control ........................................ 7
Plug in and Turn on the Receiver ................................................. 7
Wait for the Receiver to Download
ADVANCED PROGRAM GUIDE™ Data ........................................ 7
Using Highlight and Select............................................................ 8
Complete the Assisted Setup ........................................................ 8
Order Programming........................................................................ 8
Chapter 2: Using the Remote Control
Remote Control Buttons ................................................................ 9
Top of the Digital Satellite Receiver .......................................... 10
Programming the Remote Control ............................................. 10
Operating Other Components ..................................................... 11
Controlling a Second RCA Satellite Receiver............................... 11
Changing the RF Remote Control Code ..................................... 11
Code List ....................................................................................... 12
Chapter 3: Satellite Receiver Features
The Program Guide....................................................................... 14
The Channel Banner ..................................................................... 15
Displaying On-screen Guides ...................................................... 16
The Detail Guide...................................................................................16
The Grid Guide ......................................................................................16
Getting Around In the Guides ..................................................... 16
Additional Program Guides ......................................................... 18
The Channel Guide ..............................................................................18
The Logo Guide .....................................................................................18
The Suggestion Guide .........................................................................18
The Category Guide .............................................................................19
The AlphaSort™ Guide ........................................................................19
The Scout™ Guide ................................................................................19
The Profile Guide..................................................................................19
The Guide Toolbar ........................................................................ 20
Chapter 4: Using On-Screen Menus
Using the Menu System............................................................... 21
Main Menu Items ......................................................................... 21
The Program Guide....................................................................... 22
Mailbox ......................................................................................... 22
Using the Purchases Menu .......................................................... 22
Reviewing and Canceling Upcoming Purchases .........................23
Spending Limits ....................................................................................23
Pay Per View Programs .......................................................................23
Timers ............................................................................................ 24
User Profiles.................................................................................. 24
Creating and Editing User Profiles..................................................24
Creating a Profile Channel List ........................................................25
Setting the Rating Limit ....................................................................25
Viewing Hours ......................................................................................26
Setting Up Spending Limits ..............................................................26
Locking a User’s Profile ......................................................................26
Locking the System .............................................................................26
Unlocking the System.........................................................................27
Choosing Your Profile .........................................................................27
Personal Settings .......................................................................... 28
Name .......................................................................................................28
Guide Settings .................................................................................28
Channel Banner ....................................................................................28
Color Scheme ...................................................................................28
Translucency .....................................................................................28
Animation .........................................................................................28
Edit Fetch ..........................................................................................28
INFO Message ..................................................................................29
System Setup ................................................................................ 30
Assisted Setup ..................................................................................30
Receiver Index ......................................................................................30
Receiver Options ..................................................................................30
Dish Pointing .........................................................................................32
System Test............................................................................................33
System Info............................................................................................33
System Upgrades .................................................................................33
New Access Card .................................................................................33
Alternate Data ......................................................................................33
Chapter 5: Technical Information
Service Control Panel................................................................... 34
Advanced Options ........................................................................ 35
Color Bars...................................................................................... 36
Chapter 6: Other Information
Troubleshooting ............................................................................ 37
Limited Warranty ......................................................................... 41
Accessory Information ................................................................. 44
Index .............................................................................................. 45

Chapter 1: Connections & Setup
2Chapter 1
Illustrations contained in this document are for representation only.
Choose Your Connection
There are several ways to connect your digital satellite receiver depending on the components you want to connect and the quality of the signal you
want to achieve. The next four pages show three options for connecting your satellite receiver to your other components, plus instructions for
connecting an antenna for an RF remote control. Choose the connection that most closely matches your components in order to get the best signal
you can. For example, if your TV has an S-Video input, use the Excellent Connection shown on the next page as a guide. If your TV only has an RF
coaxial input, use the Basic Connection shown on page 5 as a guide.
Things To Consider Before You Connect Components
Protect Your Components from Power Surges
•Connect all components before plugging any power cords into the wall outlet.
•Always turn off the digital satellite receiver, TV and other components before you connect or disconnect any cables.
Position Cables Correctly to Avoid Audio Hum or Interference
•Insert all cable plugs firmly into their jacks.
• Place the Audio/Video (A/V) cables to the sides of the TV’s back panel instead of straight down the middle after you connect your components.
•Try not to coil any twin-lead cables and keep them away from the A/V cables as much as possible.
•Make sure all antennas and cables are properly grounded. See the inside front cover of this book for more information.
Protect Your Components from Overheating
•Do not block ventilation holes in any of the components. Arrange the components so that air can circulate freely. Remove any sales or
promotional materials attached to the product.
•Do not stack components.
•Allow adequate ventilation when placing components in a stand.
•Place an amplifier or receiver on the top shelf of the stand so heated air rising from it will not flow around other components.
DIRECTV programming is subject to the terms and conditions of the DIRECTV Customer Agreement; a copy is provided at DIRECTV.com and with your
first bill. See page 8 for more information.
Insert Your Access Card
Find the access card in the material that came with your receiver. Make sure the card is facing
up, and fully insert it into the slot on the right side of your satellite receiver.
Jacks and Cables
Below is a description of the jacks and cables you can use to make connections. Not all cables come with your digital satellite receiver.
S-Video Jack and Cable
S-Video jacks/cables provide this receiver’s best picture quality. Remember to connect the left and right audio cables to the
TV because the S-Video cable carries only the picture signal, not the sound.
Audio/Video (A/V) Jack and Cable (RCA-type)
Audio/Video (A/V) cables provide good picture quality and stereo sound, and should be used if your TV has no S-video jacks.
The digital satellite receiver’s A/V jacks are color coded (yellow for video, red for right audio, and white for left audio). If
your TV has only one input for audio (mono), connect it to the left (white) audio jack on the satellite receiver.
RF Jack and Coaxial Cable (F-type)
RF jacks provide good picture and mono sound quality. They should be used if A/V connections are not available on your TV.
RF jacks are used for off-air antenna and cable feed connections. The RF jacks on the receiver are labeled IN FROM ANT and
OUT TO TV. The coaxial cable supplied with your system is used to connect the receiver to your TV/VCR’s antenna input jack.
Telephone Jack and Cord
The telephone line cord is required to connect your satellite receiver to a telephone line if you choose to subscribe to
DIRECTV®programming. The phone line connection is used to periodically call out to DIRECTV. You will need an RJ11-type
modulator jack (the most common type of phone jack) which might look like one of those pictured here. If you don’t have
a modular jack, call your local telephone company to find out how to get one installed.
PHONE
S-VIDEO
ANTENNA IN

Chapter 1 3
Connections & Setup
Excellent Connection
Using S-Video and A/V jacks and cables to connect to the TV,
RF coaxial cables to connect the VCR
This connection provides the best picture quality, surpassing that of A/V
cables. The S-Video cable, which carries video information only, requires that
audio cables also be used for sound.
What you will need:
•Two (2) RF coaxial cables
•Two (2) A/V cables
•One (1) S-Video cable
•One (1) telephone line cord
•Coaxial cable lines fed from a digital satellite antenna and a standard TV
antenna (or cable line)
Making the Connection
1. Connect the satellite dish antenna feed (RG-6 coaxial cable) to the
SATELLITE IN jack on the satellite receiver.
2. Connect one end of an RF coaxial cable to the OUT TO TV jack on the
satellite receiver, and the other end to the antenna input jack on the VCR.
Note: If your VCR has A/V input jacks, you can use A/V cables to connect the
satellite receiver’s second A/V jacks to the A/V jacks of the VCR instead of using
the RF coaxial cable.
3. Connect one end of an RF coaxial cable to the antenna output jack on the
VCR, and the other end to the TV’s antenna input jack.
4. Connect the cable or off-air antenna feed (RF coaxial cable) to the IN
FROM ANT jack on the satellite receiver.
5. Connect one end of the supplied telephone line cord to the PHONE JACK
on the back of the satellite receiver, and the other end to an RJ11-type
modular phone jack (the most common type of phone jack).
6. Connect two ends of the supplied A/V cables to AUDIO R and L jacks on
the satellite receiver, and the other ends to the corresponding audio input
jacks on the TV.
Note: Make sure you connect jacks by their labels. For example, AUDIO R on the
digital satellite receiver should be connected to TV’s right audio input jack, L
Audio to L Audio, etc.
If your TV only has one audio input jack, use the satellite receiver’s AUDIO L jack
to make the connection.
7. Connect one end of the supplied S-Video cable to the satellite receiver,
and the other end to the S-Video input jack on the TV.
Go to Page 6
Note: Your VCR and TV back panels may not look exactly
like the ones illustrated.
Di
g
ital
S
atellite
R
ece
iv
er
Cable or
Off-air
Antenna
S
atellite
Di
s
h Ant
e
nn
a
R
J
11
mo
du
l
a
r
phone
j
ac
k
SATELLITE IN
S-VIDEO
OUT TO TV IN FROM ANT
PHONE
GROUND
– R –
AUDIO
– L –
VIDEO
LOW SPEED
DATA
RF ANT
TV
V
CR
IN
ANT
OU
T
VIDE
O
A
U
DI
O
L
R
C
H4
C
H
3
S
-VIDE
O
IN
FR
O
M
ANT
Using Your Components
To watch DIRECTV® programming:
Tune the TV to its S-Video line input (if you have difficulty finding your TV’s S-Video line input, see your TV’s User’s
Manual or page 40 in this manual). Then tune the satellite receiver to the desired channel.
To see what’s playing on the VCR:
Tune the TV to channel 3 or 4 (whichever is set on the VCR as its output channel). Begin VCR playback as usual.
1
2
3
4
5
6
7

Connections & Setup
4Chapter 1
Very Good Connection
Using A/V jacks and cables to connect to the TV,
RF coaxial cables to connect the VCR
This connection provides better picture quality than RF coaxial cables and is
recommended for use with TVs that do not have S-Video input jacks.
What you will need:
•Two (2) RF coaxial cables
•Three (3) Audio/Video cables
•One (1) telephone line cord
•Coaxial cable lines fed from a digital satellite antenna and a standard TV
antenna (or cable line)
Making the Connection
1. Connect the satellite dish antenna feed (RG-6 coaxial cable) to the
SATELLITE IN jack on the satellite receiver.
2. Connect one end of an RF coaxial cable to the OUT TO TV jack on the
satellite receiver, and the other end to the antenna input jack on the
VCR.
Note: If your VCR has A/V input jacks, you can use A/V cables to connect the
satellite receiver’s second set of A/V output jacks to the A/V jacks of the VCR
instead of using the RF coaxial cable.
3. Connect one end of an RF coaxial cable to the antenna output jack on
the VCR, and the other end to the TV’s antenna input jack.
4. Connect the cable or off-air antenna feed (RF coaxial cable) to the IN
FROM ANT jack on the satellite receiver.
5. Connect one end of the supplied telephone line cord to the PHONE JACK
on the back of the satellite receiver, and the other end to an RJ11-type
modular phone jack (the most common type of phone jack).
6. Connect the ends of the supplied A/V cables to the satellite receiver’s
AUDIO and VIDEO jacks, and the other ends to the corresponding AUDIO
and VIDEO input jacks on the TV.
Notes: Make sure you connect jacks and cables corresponding to their labels.
For example, AUDIO R output on the digital satellite receiver should be
connected to AUDIO R input on the TV, VIDEO out to VIDEO in, etc.
If your TV only has one audio input jack, use the satellite receiver’s AUDIO L
jack to make the connection.
Go to Page 6
Di
g
ital
S
atellite
R
ece
iv
er
Cable or
Off-air
Antenna
S
atellite
Di
s
h Ant
e
nn
a
R
J
11
mo
du
l
a
r
phone
j
ac
k
SATELLITE IN
S-VIDEO
OUT TO TV IN FROM ANT
PHONE
GROUND
– R –
AUDIO
– L –
VIDEO
LOW SPEED
DATA
RF ANT
TV
V
CR
IN
ANT
OU
T
VIDE
O
A
U
DI
O
L
R
C
H4
C
H
3
FR
O
M
ANT
Note: Your VCR and TV back panels may not look exactly
like the ones shown.
Using Your Components
To watch DIRECTV® programming:
Tune the TV to its video line input (if you have difficulty finding your TV’s video line input, see your TV’s User’s
Manual or refer to the instructions on page 40 in this manual). Then tune the satellite receiver to the desired
channel.
To see what’s playing on the VCR:
Tune the TV to channel 3 or 4 (whichever is set on the VCR as its output channel). Begin VCR playback as usual.
1
2
3
4
5
6

Chapter 1 5
Connections & Setup
Basic Connection
Using RF Coaxial cables for all connections
This connection provides standard picture quality. This connection is only
recommended for use with TVs that do not have S-Video or A/V input jacks.
What you will need:
•Two (2) RF coaxial cables
•One (1) telephone line cord
•Coaxial cable lines fed from a digital satellite antenna and a standard TV
antenna (or cable line)
Making the Connection
1. Connect the satellite dish antenna feed (RG-6 coaxial cable) to the
SATELLITE IN jack on the satellite receiver.
2. Connect one end of an RF coaxial cable to the OUT TO TV jack on the
satellite receiver, and the other end to the antenna input jack on the
VCR.
Note: If your VCR has A/V input jacks, you can use A/V cables to connect the
satellite receiver’s second A/V jacks to the A/V jacks of the VCR instead of
using the RF coaxial cable.
3. Connect one end of an RF coaxial cable to the antenna output jack on
the VCR, and the other end to the TV’s antenna input jack.
4. Connect the cable box or off-air antenna feed (RF coaxial cable) to the
IN FROM ANT jack on the satellite receiver.
5. Connect one end of the supplied telephone line cord to the PHONE JACK
on the back of the satellite receiver, and the other end to an RJ11-type
modular phone jack (the most common type of phone jack).
Go to Page 6
Di
g
ital
S
atellite
R
ece
iv
er
Cable or
Off-air
Antenna
S
atellite
Di
s
h Ant
e
nn
a
R
J
11
mo
du
l
a
r
phone
j
ac
k
SATELLITE IN
S-VIDEO
OUT TO TV IN FROM ANT
PHONE
GROUND
– R –
AUDIO
– L –
VIDEO
LOW SPEED
DATA
RF ANT
TV
V
CR
IN
ANT
OU
T
VIDE
O
A
U
DI
O
L
R
C
H4
C
H
3
FR
O
M
ANT
Note: Your VCR and TV back panels may not look exactly
like the ones shown.
Using Your Components
To watch DIRECTV® programming:
Tune the TV to the satellite receiver’s output channel (either channel 3 or 4).
Note: You can change the satellite receiver’s output channel by pressing the remote control’s DIRECTV button, then the MENU button,
then select System Setup, then System Options, and finally select Output Channel. Use the remote control’s arrow and SELECT buttons
to highlight and select the desired output channel. Tune the TV to that channel to see the satellite receiver’s picture.
To see what’s playing on the VCR:
Tune the TV to channel 3 or 4 (whichever is set on the VCR as its output channel). Begin VCR playback as usual.
1
2
3
4
5

Connections & Setup
6Chapter 1
Satellite Receiver Rear Panel
This diagram illustrates each of the back panel jacks found on
your digital satellite receiver. When working with cables, be
sure to connect corresponding outputs and inputs (Video out
to Video in, Right Audio out to Right Audio in, etc.).
For more information on the function of the back panel jacks
and many other features of your digital satellite receiver, press
the MENU button and select System Setup from the Main
menu, then select Receiver Index.
SATELLITE IN
S-VIDEO
OUT TO TV IN FROM ANT
PHONE
GROUND
– R –
AUDIO
– L –
VIDEO
LOW SPEED
DATA
RF ANT
Back Panel Jacks (in alphabetical order)
AUDIO (R and L) Audio cables offer better sound quality than RF coaxial cables. Connect a second set of audio cables to another component, such
as a VCR or stereo.
Note: If your TV only has one audio input jack, use the satellite receiver’s AUDIO L jack to make the connection.
IN FROM ANT Connect a standard TV antenna or cable feed to the satellite receiver using this jack. You can then switch between the satellite
receiver’s signal and the TV/cable feed using the remote control’s ANTENNA button to toggle between the two.
LOW SPEED DATA This port allows you to connect your digital satellite receiver to future services and accessories as they become available. A
shielded cable and additional hardware may be required.
OUT TO TV Connects the satellite receiver to your TV or VCR using RF coaxial cable. This jack provides the most basic connection, carrying average
sound and video quality.
PHONE Connects the satellite receiver to a telephone line. The digital satellite receiver requires a telephone line connection to periodically
communicate with your program provider.
RF ANT This jack connects an antenna that allows the remote control to use both infrared (IR) for line-of-sight, and radio-frequency (RF) signals,
which work through walls, to operate the satellite receiver.
SATELLITE IN Use to connect the satellite receiver to the satellite dish antenna.
S-VIDEO Provides better picture quality than VIDEO or RF coaxial cable jacks. If your TV has an S-Video jack, use it along with the audio jacks (S-
Video only carries picture information, not sound) to connect to your TV.
VIDEO Provides better picture quality than the OUT TO TV jack. Connect the second VIDEO jack to another device, such as a VCR. You must also
connect the AUDIO cables when using the VIDEO connection.
S
ATELLITE I
N
S
-VIDE
O
OU
T T
O
T
V
IN FR
O
M AN
T
PH
O
N
E
GROUND
–
R
–
A
U
DI
O
–
L
–
VIDE
O
RF ANT
RF Remote Antenna Connection
This connection allows your remote control to communicate with
your digital satellite receiver even when you do not have line-of-
sight to the receiver’s front panel remote sensor.
Just as you would adjust a rabbit-ear antenna to get a better
picture, your RF remote may need similar adjustments depending
upon your environment. RF remote performance will be optimal
when the receiving antenna is moved away from other electrical
noise sources such as computers, VCR’s, video games, etc., and the
cables connecting these products.
Note: The RF antenna can be connected to the IRD using standard 75 ohm
TV coaxial cable which will allow greater flexibility in positioning the
antenna away from noise sources for best performance.
What you will need:
•One RF remote antenna
Making the Connection
Connect the RF remote antenna to the RF ANT jack on the back of your digital satellite receiver.
Using Your Component
As soon as the above connection is made, the RF feature of your remote is in effect. For information about programming the remote control to
operate other devices, see page 10. If you have other RF remote controls, you may want to change the RF code to avoid conflicts. To change the RF
code, see the instructions on page 11.

Chapter 1 7
Connections & Setup
Place Batteries in the Remote Control
Follow these steps whenever you need to install or change the batteries in your digital satellite
receiver’s remote control.
Note: When replacing old batteries, you may need to reprogram the remote control to operate other devices.
Avoid pressing any of the remote control buttons while you’re replacing old batteries. If you press a remote control
button while replacing batteries, you will need to reprogram the remote control to operate other devices.
1. Remove the cover from the battery compartment.
2. Insert batteries in the battery compartment, matching
the + and – end of each battery.
3. Replace the cover.
Plug in and Turn on the Receiver
Plug the end of the power cord into the wall outlet. Be sure to insert the plug completely.
To turn on the satellite receiver, press the DIRECTV button on the remote control or the ON•OFF
button on the front panel. If your TV brand is RCA, GE, or Proscan, press the TV button on the remote
control to turn on the TV. If your TV brand is not RCA, GE, or Proscan, see page 10 in the next section,
Using the Remote Control, for details on programming the satellite receiver’s remote control to
operate your TV.
Note:
The message “Searching for Satellite Signal” might
appear briefly at the bottom of your screen when
you turn on your satellite receiver for the first time.
This is normal.
If this message stays on the screen for more than
one minute, check your receiver’s on-screen signal
meter to make sure your antenna is receiving the
strongest possible satellite signal. See “Signal
Meter” on page 32 for more information.
Wait for the Receiver to Download ADVANCED PROGRAM GUIDE™ Data
The first time you connect a receiver to a satellite antenna you’ve already installed and pointed
correctly, the receiver starts to gather information for the program guide.
After you turn on your receiver and tune your TV to the correct video input channel, a progress bar
appears indicating that the receiver is gathering this program guide information.
To prevent any damage to your TV screen, the progress bar disappears after 2 minutes (the screen
goes blank).
Note: When the progress bar reaches 100%, there might be a delay before you actually see video on the screen.
If the screen stays blank for more than 2 to 3 minutes, you need to reset the receiver.
To reset the receiver:
1. Unplug the satellite receiver’s power cord from the power outlet.
2. Wait a few seconds, and plug the power cord back into the outlet.
3. Turn on the receiver and wait for it to download program guide information.
Note
The Satellite Data Acquisition screen will also
appear when:
• your unit loses power (either from a power
outage or being unplugged)
• your unit loses the satellite signal for an
extended period of time.

Connections & Setup
8Chapter 1
Using Highlight and Select
All on-screen menus can be handled the same way, using highlight and select navigation.
Highlight and select navigation has two steps:
1. Use the arrow buttons (up, down, left, and right) on the remote control to highlight different
choices on the screen.
2. Press SELECT to select the highlighted item.
Note: When a highlighted on-screen menu choice has a number beside it, you can also press the corresponding
number button on the remote control to select it.
Once you know how to navigate on-screen menus, you can complete the Assisted Setup (see the next
step) and explore the menu system.
To display the on-screen menu system, press the remote control’s DIRECTV button, then press the
MENU button.
Note: Don’t worry about getting stuck inside a menu. Pressing the CLEAR button on the remote control takes you out
of the menu system and back to the program you were watching.
TV
ON•OFF
VCR
AUX2
DVD
FETCH GO BACK
SKIPMUTE
INFO
MENU CLEAR
GUIDE
AUX1
VOL
VOL
CH -
CH +
(-)
SELECT
DIRECTV
SELECT
button
MENU
button
CLEAR
button
Arrow
buttons
DIRECTV
button
Complete the Assisted Setup
If you installed your satellite dish antenna yourself, you may have already used the Assisted Setup to find dish-pointing coordinates, acquire and fine-
tune the signal, and run a system test.
If you need to run the setup again, select System Setup from the Main menu, then select Assisted Setup.
To check your dish-pointing coordinates or run the signal strength meter, display the Main menu, then select System Setup, and finally Dish Pointing.
Order Programming
After you have installed your DIRECTV® System, you should contact DIRECTV to order DIRECTV®
programming.
With this receiver and the proper satellite dish antenna, you may be able to subscribe to local
channels from DIRECTV in certain areas. Additional equipment may be required in some markets.
Check with your retailer or visit DIRECTV.com for information on availability of local channels from
DIRECTV in your area.
ACTIVATION OF PROGRAMMING MAY BE SUBJECT TO CREDIT APPROVAL AND REQUIRES VALID
SERVICE ADDRESS, SOCIAL SECURITY NUMBER AND/OR MAJOR CREDIT CARD. DEPOSIT OR
PREPAYMENT MAY BE REQUIRED. Professional and collegiate sports subscriptions sold separately.
Eligibility for local channels based on service address within certain designated market areas as
defined by Nielsen Media Research, Inc. In some areas served by members or affiliates of the National
Rural Telecommunications Cooperative, local channels may be available from DIRECTV rather than the
NRTC member or affiliate. Programming, pricing, terms and conditions subject to change. Hardware
and programming sold separately. Pricing is residential. Taxes not included. Equipment specifications
and programming options may vary in Alaska and Hawaii. DIRECTV services not provided outside the
U.S. DIRECTV programming is sold separately and independently of DIRECTV System hardware. A valid
programming subscription is required to operate DIRECTV System hardware. Receipt of DIRECTV
programming is subject to the terms of the DIRECTV Customer Agreement; a copy is provided at
DIRECTV.com and in your first bill. Activate your DIRECTV®programming today at 1-800-DIRECTV
(1-800-347-3288).
Tip
When you order programming, you need to know
your access card and receiver ID numbers. To get
these numbers, select System Setup from the Main
menu, then System Test.
Wait for the system to run all of its tests. The access
card and receiver ID numbers are displayed at the
end of the system test.
Write the access card and receiver ID numbers in the
space below for easy reference:
Important!
If local channels are available in your area and you
decide to subscribe, the receiver will need to
download all of your program guide information
again. This might take a few minutes. See “Wait for
the Receiver to Download ADVANCED PROGRAM
GUIDE™ Information” on page 7 for more
information.