Thundercomm TurboX C450 User manual

Thundercomm TurboX™Development Kit
Quick Start Guide
Machine Type: C450, CM450, CM625, and C626
Rev. V1.0
Feb 23, 2021
DN: TC_4&6_510
Empowering Every IoT Device with Our Technology

Thundercomm TurboX™ Development Kit Quick Start Guide
Copyright©2021 Thundercomm Technology Co., Ltd. All rights reserved.
Revision History
Revision
Date
Description
1.0
Feb 23, 2021
Initial release

Thundercomm TurboX™ Development Kit Quick Start Guide
Copyright©2021 Thundercomm Technology Co., Ltd. All rights reserved.
Table List
Table 2-1: Equipment required to install and run the LA SDK (Software Development Kit)
Table 3-1: Top view specifications
Table 3-2: Bottom view specifications

Thundercomm TurboX™ Development Kit Quick Start Guide
- 1 -
Contents
Chapter 1. Introduction..............................................................................................- 2 -
Chapter 2. Equipment Requirements .......................................................................- 3 -
Chapter 3. Board Overview .......................................................................................- 4 -
1. Front view ..........................................................................................................................- 4 -
2. Back view...........................................................................................................................- 6 -
Chapter 4. Quick Start ...............................................................................................- 8 -
1. Power on with power key ...................................................................................................- 8 -
2. Power on with USB............................................................................................................- 8 -
3. Reset .................................................................................................................................- 9 -
Chapter 5. System Image Flashing.........................................................................- 10 -
Chapter 6. Service....................................................................................................- 11 -
Appendix 1. Intellectual Property Statement............................................................ - 12 -
Appendix 2. Trademarks ............................................................................................- 13 -

Thundercomm TurboX™ Development Kit Quick Start Guide
- 2 -
Chapter 1. Introduction
This quick start guide provides detailed information on equipment requirements, board overview,
startup, and system images programming.
This document shall take CM450 SOM (System on Module) as an example.
Conventions:
Function declarations, function names, type declarations, attributes, and code samples appear
in a different format, for example, cp armcc armcpp.
Code variables appear in angle brackets, for example, <number>.
Button, tool, and key names appear in bold font, for example, click Save or press Enter.
Commands to be entered appear in a different font, for example:
$adb devices.
On the host computer use # as shell prompt, for example:
#logcat.
On the target device use $ as shell prompt, for example:
$adb shell

Thundercomm TurboX™ Development Kit Quick Start Guide
- 3 -
Chapter 2. Equipment Requirements
Table 2-1: Equipment required to install and run the LA SDK (Software Development Kit)
Equipment
Description
Turbox 450-626 Platform
Based on the Qualcomm®
SDA450/SDM450/SDM625/SDA626 processor
Power adapter
12 V
2000 mA
USB to Micro USB cable
Connect serial console interface to run ADB
USB to Type-C USB cable
Connect Type-C USB 3.0 port to flash images
Host computer
Connect the development board to install
Fastboot

Thundercomm TurboX™ Development Kit Quick Start Guide
- 4 -
Chapter 3. Board Overview
1. Top view
Figure 1: Top View
Table 3-1: Top view specifications
1. RJ45 Gigabit Ethernet Connector
2. Type-C USB Connector
3. USB 3.0 Connector x 2
4. USB 3.0 Connector x 2
5. Fan Pin
6. UART TTL Pin

Thundercomm TurboX™ Development Kit Quick Start Guide
- 5 -
7. RS232 Pin
8. DC Power Connector
9. RTC Battery
10. A+G Sensor
11. Battery Port
12. PM8953 Speaker Pin
13. PM8953 Headset Port
14. Button
15. UART Jumper Pin
16. WCD9335 Headset Port
17. WCD9335 Speaker Pin
18. Switch 3
19. FM Antenna
20. Switch 2
21. 4G DRX Antenna
22. HDMI IN
23. LVDS Screen Pin
24. HDMI OUT
25. eDP Port
26. Switch 1
27. NFC Antenna Welding Point
28. Debug USB
29. WCD9335 MIC4
30. GPS Antenna
31. 4G PRI Antenna
32. BT/WIFI Antenna

Thundercomm TurboX™ Development Kit Quick Start Guide
- 6 -
2. Bottom view
Figure 2: Bottom View
Table 3-2: Bottom view specifications
1. PM8953 MIC1
2. Distance+ Ambient Light Sensor
3. Atmospheric Pressure Sensor
4. Magnetometer
5. WCD9335 MIC3
6. SIM2
7. SIM1
8. LCD Connector
9. PM8953 MIC2
10. CSI0
11. CSI1
12. CSI2

Thundercomm TurboX™ Development Kit Quick Start Guide
- 7 -
13. Flash LED
14. WCD9335 MIC2
15. TF Card Port
16. WCD9335 MIC1

Thundercomm TurboX™ Development Kit Quick Start Guide
- 8 -
Chapter 4. Quick Start
1. Power on with power key
Connect the 12V power adapter, press power key, then the LED on board will blink quickly.
2. Power on with USB
Step 1. Connect the 12V power adapter.
Step 2. Connect Thundercomm TurboXTM CM450 Open Kit to your computer with the USB cable.
Step 3. To check if the board has powered on, open the Terminal in Linux system, input Isusb, and
press Enter. Your device successfully powered on and connected to computer with the
following log displaying on your screen.

Thundercomm TurboX™ Development Kit Quick Start Guide
- 9 -
3. Reset
In Terminal window of Linux, input adb reboot, and press enter, the system will reboot.

Thundercomm TurboX™ Development Kit Quick Start Guide
- 10 -
Chapter 5. System Image Flashing
Refer to [TC_4&6_110]_Thundercomm TurboX C450,CM450,CM625,C626 Development
Kit_Release Notes_V1.0.pdf.

Thundercomm TurboX™ Development Kit Quick Start Guide
- 11 -
Chapter 6. Service
If you have any problem, please propose a request in the Thundercomm TurboX 450-626 Platform
forum: https://www.thundercomm.com/forum/category/2/thundercomm-turbox-som-platform.
For business cooperation, please email us at: [e-mail].

Thundercomm TurboX™ Development Kit Quick Start Guide
- 12 -
Appendix 1. Intellectual Property Statement
This document itself and the proprietary technical information contained herein is the property of
Thundercomm. Without prior written authority of Thundercomm, no one shall copy, modify, or reprint
the whole or part of this document. Offenders are liable for all related damages, loss, and litigations.
Documentation content is subject to change without notice. Thundercomm makes constant
improvements on the documentation.

Thundercomm TurboX™ Development Kit Quick Start Guide
- 13 -
Appendix 2. Trademarks
Hexagon is a trademark of Qualcomm Technologies, Inc. and/or its affiliated companies. Arm is a
registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere. All other
trademarks are the property of their respective owners.