Timago H011 User manual

1
INSTRUCTIONS FOR USE
Steel wheelchair
Product code: H011
1. Characteristics
The wheelchair is made of powder coated steel frame. It possesses
durable, black, and nylon-cotton seat and cushion. The wheelchair is
equipped with height adjustable, flip-up armrests. Footrests are
available either in standard (swing away) version or in elevating legrest
version. Rear wheels (24’’) consist of steel spokes and are equipped
with pneumatic or solid rubber tyres. Front wheels (8’’) are made of
higher-strength rubber resistant to abrasion.
Additional options: solid rubber rear wheels, elevating legrest,
attendant brakes, table.
The set includes:
•Frame with seat
•Right footrest with footplate
•Left footrest with footplate
•Protective strap
•Pump
•Set of keys for wheelchair
assembly/dismantling
Elements of the wheelchair:)
a. Hand grip
b. Armrest with
height adjustment
c. Locking pin of
the armrest
d. Wheel lock

2
e. Hand rim
f. Quick release
g. Footrest
h. Assembly pin of the footrest
2. Application
The wheelchair is designed for people who have problems with
unassisted moving and for patients with dysfunctions and reduced
mobility. This self propelled wheelchair can also be pushed by the
accompanying person. The wheelchair is suitable for indoor and
outdoor use.
3. Assembly
UNFOLDING AND ASSEMBLY
Step 1. Unfolding the wheelchair
Place the wheelchair on the ground. Unfold the wheelchair by using
the hand grips which are at the back of the backrest. Then, press the
front and rear edge of the seat so that all the elements fit together.
Step 2. Assembly of footrests
Assemble the right and the left footrest in the front part of the frame
by placing them on two pins and turn them inwards until they are
locked.
Step 3. Adjustment of footplates
Adjust the right and the left footplate with the use of pins and locking
clips which is placed on the footrest. In case of elevating legrest, adjust
the angle of inclination to the ground using the lever. Proper space
should be left between the footplates and the ground as footplates set
too low may cause difficulties in overcoming such obstructions as curb.
Adjust the footplates so that the angle between trunk and thighs is 900
(optimum sitting position is provided to the user, then).

3
Step 4. Assembly of protective strap
Put the protective strap on the footrests as it prevents user’s legs from
sliding down under the wheelchair from footplates.
Note! Do not use the wheelchair without protective strap.
On completion of the above activities, the wheelchair is ready to use.
FOLDING
The wheelchair can be re-folded in order to be transported and stored
more easily.
•Before folding the frame, swing away the footplates and set them
in vertical position (perpendicularly to the ground).
•To fold the frame, pull the seat upwards by holding the front and
the back edge in the middle, so that the frame jumps out from the
connecting elements.
FLIP-UP FUNCTION OF ARMRESTS
•Press the locking button located in the front part of the armrest
and push the armrest backwards.
•To close the armrest, push it downwards so that the locking
button clicks.
HEIGHT ADJUSTMENT OF ARMRESTS
•To adjust the height of the armrest, pull the locking clip on the
inside of the armrest frame.
•Then raise the armrest up or lower it down (in 2.5 cm increments)
and release the locking clip.
PUMPING THE WHEELS
•The wheelchair was optionally equipped with pneumatic rear
wheels 24’’ in diameter and swivel, PU front wheels 8’’ in
diameter (tubeless tyre). Remember to control the air pressure in

4
both wheels and check the condition of the tyres in search of
abrasions, cuts or surface depletion.
•To balance the air pressure in the wheels, twist off the cap of the
valve, insert the pump (included in the set) into the valve, and
pump the air.
WHEEL LOCKS
•To lock the wheels, push the lock lever forwards until the wheel is
fully blocked (separately for left and right wheel). Please, note
that the wheel lock only serves to lock the wheels when the
wheelchair is at a complete stop.
WHEEL LOCKS ADJUSTMENT
The correct lock of the wheel lock depends on its adjustment and
position. The handle of the wheel lock should be positioned so that the
wheel lock shoe blocks the wheel firmly and the lever does not face
excessive resistance.
•In case of excessive resistance, pull the handle forwards slightly by
twisting off the locking screw which is located on the other side of
the wheel lock (from the inside of the wheelchair). Set the wheel
lock shoe in such position that the wheel lock blocks the wheel
easily and without resistance.
•When the wheel lock shoe does not touch or block the wheel
sufficiently, follow the above instruction by moving the handle in
the opposite direction.
SEAT BELTS
The belt, which is included in the standard equipment, protects the
trunk in cases when the user slides down from the wheelchair or is not
able to keep correct position independently. The belt is fastened with
the use of buckle.

5
4. Technical data
Overall width
57-67 cm
Inner width
40, 43, 46, 48, 51 cm
Overall depth
104 cm
Seat height from the ground
50 cm
Overall height
91 cm (88 cm)
Seat dimensions
39, 42, 45, 47, 50 cm x 40 cm
Weight
18.6-21 kg
Maximum capacity*
115 kg up to the width 48 cm
135 kg for the width 51 cm
Folded width
30 cm
Frame colour
silver, dark blue
* depending on seat width
5. Notes
Timago International Group does not bear responsibility of improper
use of the wheelchair, failure to comply safety regulations and
misuse.
6. Cleaning and maintenance
Carry out the maintenance of the wheelchair components regularly:
•The upholstery and the cushion can be cleaned with damp (not
wet) cloth and cold or warm water, without the use of detergents.
Difficult stains can be cleaned with a sponge. Do not soak the
upholstery too much. Dry away from heat sources.
•Plastic elements should be cleaned with damp cloth possibly with
the use of appropriate detergents for plastic elements. In such
case follow the instructions given by the producer and safety
measures.

6
7. Storage and transport conditions
Device should not be exposed to direct sunlight, water or moisture.
8. Warranty information
All products distributed by our company are covered by a warranty, the
terms of which are described in the warranty card available on our
website. Please contact the retailer from whom you purchased the
product. Please, keep in mind that for warranty purposes, the proof of
purchase (receipt or invoice) should be retained.
9. Labels
Reference
number
Manufacturer
LOT number Manufacture date
Serial number Medical device
Note
Please read the
instruction
The manufacturer checked for compliance with
essential medical devices requirements.
Our complete line of products is available from our distributors.
Learn more at: www.timago.com. Thank you for choosing Timago!

7
Timago International Group
Spółka z o.o. i Spółka – Spółka komandytowa
ul. Karpacka 24/12
43-316 Bielsko-Biała, Polska
T.: [phone]
F.: [phone]
E.: [e-mail]
Rev. II, date 20.05.2021