Timago FS 654 LGC User manual

1
USER MANUAL
Aluminium reclining wheelchair with toilet function
Product code: FS 654 LGC
Dear Customers,
Thank you for purchasing our product. We hope that the equipment you have selected will meet
your expectations. We would like to share some important information with you.
Timago International Group is a Polish company which distributes medical, rehabilitation and
orthopaedic products to pharmacies and medical stores.
Our mission is to ensure your comfort by offering safe, functional, and high-quality products.
We have many years of experience in this sector. Timago products reach a wide range of users in
Poland and throughout Europe through our distributors (medical retailers).
Timago’s company culture promotes openness to your needs. Our goal is to promote safe and
correct use of our products for treatment and rehabilitation in order to improve comfort and quality
of life.
We invite you to access our website for more information: timago.com.

2
1. Introduction
Prior to use of our products you should inspect the equipment for any defects which may have
occurred during transport. If this happens, please contact your retailer.
Then, please read this instruction which includes important information for the user.
Please contact us if you have any questions concerning the use of the equipment. Our advisors will
provide you with any information you require on an ongoing basis.
Please note that if you have questions other than those concerning the use of our products, you
should contact your doctor, nurse or physical therapist.
2. Characteristics
The wheelchair is made of aluminium frame reinforced with cross bar. The seat and backrest are
made of material resistant to dirt and water. The wheelchair is equipped with toilet bucket, extended
backrest, anti-tip wheels, pillow, and stabilizing belts. The backrest and footrests’ angle can be
adjusted within the range of 0o-90o. Detachable armrests are made in a long version. The wheelchair
is supplied with pneumatic rear wheels (24’’) with aluminium handrims and solid front wheels (8’’).
The wheelchair is specially recommended to the users with neurologic disorders.
The set includes:
•Frame with seat
•Right footrest with footplate
•Left footrest with footplate
•Extended backrest
•Pillow stabilizing head
•Seat with wedge
•Toilet bucket
•Pump
•Set of keys

3
Elements of the wheelchair:
a. Hand grip
b. Function of backrest inclination
c. Armrest
d. Locking pin
e. Toilet bucket
f. Wheel lock
g. Handrim
h. Calf pad
i. Footrest
j. Mounting element of the footrest
k. Footrest lever
l. Adjustment of the centre of gravity
m. Anti-tip wheels
3. Application
Aluminium wheelchair is designed for people who have problems with unassisted moving and for
patients with dysfunctions and reduced mobility. The wheelchair functions as a means of transport,
stabilization, and a toilet owing to the toilet bucket. The wheelchair facilitates the user everyday
hygiene. Velcro-fastening headrest is an additional advantage as its position might be adjusted to the
individual needs of the user. This self propelled wheelchair can also be pushed by the accompanying
person owing to the hand grips fixed on the backrest. Owing to the extended backrest, the position
of the sitting person is even better stabilized. The wheelchair can be used at home, in hospitals,
clinics, and hospices. The wheelchair is especially recommended to people who have problems with
mobility caused by:
•paralysis
•cerebral palsy
•limbs injuries or amputations
•degenerations or deformity of limbs
•heart and blood vessels disease, circulatory disorders
•overweight or abnormal underweight

4
4. Assembly and general recommendation for use
Note! Follow the information contained in this manual while assembly and adjustment. Users with
reduced mobility may need help from a third person who has appropriate skills.
Note! Do not sit in the wheelchair or use it in any other way before completion of assembly.
UNFOLDING AND ASSEMBLY
Step 1. Unfolding the wheelchair
Place the wheelchair on the ground. Unfold the wheelchair using the hand grips at the back of the
backrest. Fix the seat into the mounting openings and slide the wedge.
Step 2. Assembly of toilet bucket
Slide the toilet bucket without the lid into the rails which are located under the seat. (Check the
correctness of the assembled toilet bucket).
Step 3. Assembly of footrests
Assemble the right and the left footrest. Place the mounting element into the opening in the front
part of the frame and turn it inwards until the footrest lever is locked.
Step 4. Adjustment of footplates
Adjust the right and the left footplate by tightening the screw placed at the bottom of footrest with
included key. Then, adjust the inclination angle of the footplate to the ground using the lever. Proper
space should be left between the footplates and the ground as footplates set too low may cause
difficulties in overcoming such obstructions as curb. Adjust the footplate so that the angle between
trunk and thighs is 90o(as a result the user does not need to contract legs).
Step 5. Assembly of backrest extension
Assemble the backrest extension on the wheelchair backrest by putting it into the mounting
openings until the locking clip clicks, and then, fix the pillow stabilizing head with the use of Velcro.
FOLDING
The wheelchair can be re-folded in order to be transported and stored more easily.
Step 1. To fold the wheelchair, remove the toilet bucket first and disassemble the seat.
Step 2. Disassemble the headrest.
Step 3. Turn around the calf pad, swing away the footplates and set them in vertical position
(perpendicularly to the ground).

5
Step 4. Grab the straps which are on the both sides of seat frame and pull them upwards until the
frame of the wheelchair is folded.
WHEEL LOCKS
•To lock the wheels, push the wheel lock lever forwards until the wheel is fully blocked
(separately for left and right wheel). Please, note that the wheel lock only serves to lock the
wheel when the wheelchair is at a complete stop.
WHEEL LOCKS ADJUSTMENT
The correct lock of the wheel lock depends on its adjustment and position. The handle of the wheel
lock should be positioned so that the wheel lock shoe blocks the wheel firmly and the lever does not
face excessive resistance.
•In case of excessive resistance, pull the handle forwards slightly by twisting off the locking
screw which is located on the other side of the wheel lock (from the inside of the
wheelchair). Set the wheel lock shoe in such position that the wheel lock blocks the wheel
easily without resistance.
•When the wheel lock shoe does not touch or lock the wheel sufficiently, follow the above
instruction by moving the handle in the opposite direction.
FOLDING BACKREST
Smooth adjustment, up to horizontal position, is possible owing to levers located above the hand
grips on the back of the backrest.
DETACH FUNCTION OF ARMRESTS
•To dismantle the armrest, press the locking pin located at the front part of the armrest and
remove the whole armrest from the mounting openings.
•To assemble the armrest, put the back part of the armrest into the mounting element and
close the armrest until the locking pin clicks.
PUMPING THE WHEELS
•The wheelchair was equipped with pneumatic rear wheels (24’’) and swivel, PU front wheels
8’’ in diameter (tubeless tyre). Remember to control the air pressure in both wheels and
check the condition of the tyres in search of abrasion, cuts or surface depletion.
•To balance the air pressure in the wheels, turn off the cap of the valve, insert the pump
(included in the set) into the valve, and pump the air.

6
ADJUSTMENT FOR PATIENTS AFTER AMPUTATION IN THE LOWER LIMBS AREA
Note! For professional adjustment, ask your retailer or other person who has appropriate knowledge
and qualifications. Do not adjust inclination angle by yourself.
•To adjust the centre of gravity, unscrew the fixing screw in right and left wheel. Then, set the
seat inclination by moving the fixing axis upwards or downwards, the same in both wheels.
•The seat inclination angle should be set in such a way that the user does not slide down from
the wheelchair and can freely use handrims.
SEAT BELT
The belt, which is included in the standard equipment, protects the trunk in cases when the user
slides down from the wheelchair or is not able to keep correct position independently. The belt is
fastened with the use of buckle.
Note! The belt does not guarantee complete safety. It is possible that in some situations the belt
will not fulfill its function. In such case undertake other safety measures and use other belt, e.g.
with perineal band or with braces (depending on illness and the stage of dysfunction). To choose
suitable belt, contact with the retailer.
TOILET FUNCTION
From the front slide the toilet bucket into the locking rails which are under the seat.
Before each use, make sure that the toilet bucket is firmly assembled under the seat and the wedge
is removed.
Note! During transport it is recommended to use full seat with wedge.
Note! Remember to empty toilet bucket after each use.
WHEELCHAIR HANDLING
Note! The assistance of the third person may be required while first use regardless of the user’s
health condition.
BEFORE USE
Step 1. Checking the condition of the wheelchair
Check the condition of the wheel lock, construction and tyres. Check also the correctness of the
assembled components and their adjustment.
Note! Do not use the wheelchair if any defects or deficiencies are noticed.

7
Step 2. Engaging the wheel lock
Engage the wheel lock when getting in or out the wheelchair.
Step 3. Setting the footplates
The footplates should be in vertical position when getting in or out the wheelchair. Do not use the
footplates as a support while getting in or out the wheelchair due to the risk of wheelchair tipping
over and falling.
Note! Do not stand on the footplates due to the risk of damage.
Step 4. Setting the wheels
Front wheels should be positioned in the direction of riding.
Step 5. Getting in the wheelchair
The wheelchair should be located at the place of changing the seat as close as possible. The
wheelchair should touch the bed or other seat being used, rear wheel and front element of the
frame. If the user cannot change his/her seat independently, transfer the user to the wheelchair.
Step 6. Unfolding the footplates
When the user sits in the wheelchair, unfold the footplates parallel to the ground so that his/her feet
are on the footplates while using the wheelchair. If necessary, adjust the elevating legrest using the
lever.
Step 7. Correct position of the user
The user should sit in the upright position and his/her knees should be bent at the angle of 90o.
The wheelchair is ready to use.
SAFETY USAGE
•Lifting the object from the ground may be dangerous for the person sitting in the wheelchair
as the shift of the centre of gravity may cause the wheelchair to tip over with the user. In
order to lift the object from the ground, a third person should be asked for help or a special
instrument should be used.
•Be particularly careful while riding upwards or downwards the inclined surfaces. When the
wheelchair is on the inclined surface, the accompanying person should always stand below
and protect the wheelchair from sliding down or tipping over. The center of gravity is always
at the back of the wheelchair!

8
•Remember that a heavy object hung on the backrest may change the centre of gravity.
•Be particularly careful when the accompanying person drives into a curb, a stair or some
other obstacles. It is essential not to lean over the wheelchair beyond its point of gravity as
the wheelchair may tip over. The weight of the wheelchair with the user will have to be
maintained by the accompanying person.
•Make sure that the accompanying person is strong enough to push the wheelchair safely.
•Do not use the wheel lock in order to slow down the wheelchair. Engaging the wheel lock
while the wheelchair is moving may pose threat to user’s safety.
•Do not use the wheelchair under the influence of alcohol or medicine that may impair the
ability of machine or vehicles operation. It concerns both the user of the wheelchair and the
accompanying person.
Note! Do not exceed maximum capacity of the wheelchair!
Note! Do not transfer the wheelchair by grasping the armrests or footrests. The wheelchair
should be transferred by grasping the frame construction. It is unacceptable to transfer the
wheelchair with the user.
Note! The wheelchair can be used both inside and outside the buildings ONLY on hardened and
even surfaces. It is unacceptable to use the wheelchair on icy, wet, greasy, and strongly sanded
surfaces as they do not provide firm stability to the user. Do not use the wheelchair outdoors
under unfavourable weather conditions.
Note! Do not overcome architectonic obstacles rapidly what affects the user’s safety. In cases of
significant difficulties, you should ask for help at least one fit person.
Note! Do not ride through e.g. doors without checking whether their width is greater than the
outer width of the wheelchair.
Note! Do not sit on the wheelchair when it is not properly unfolded and the frame is not in
connecting elements.
Note! Do not place any objects between the spokes as it may lock wheels.
Note! Do not use the wheelchair to transport heavy objects.
Note! Do not climb on the wheelchair, stand on the seat and its remaining parts.
INDEPENDED USE OF THE WHEELCHAIR
The user may use the wheelchair independently using the handrims fixed to the wheels. Depending
on user’s strength and health conditions, it is possible to move on the wheelchair and turn into
desired direction independently. Using the wheelchair requires basic skills in controlling over the
device.

9
Note! A help from the third person is required to overcome difficult ground barriers (ramps, steps,
stair, etc.)
Note! First independent attempts should be undertaken under the security of the third person!
Moving forwards. First steps
Step 1. Place hands on handrims.
Step 2. Lean forwards slightly.
Step 3. Move your arms forward, straightening your elbows using the same force in both hands.
Step 4. Release the handrims.
Step 5. The wheelchair was put in motion. Grab the handrims again.
Step 6. Make next cycles of movements looking ahead.
Braking
•To brake, stop the handrims with your hands gradually or make a slight backward move.
Moving backwards
•Put hands on handrims in the front part of the wheels so that they are straight in elbows.
•Make a move backwards by pulling right and left handrim using the same force in both
hands.
•Watch the course of the wheelchair by turning the head back and forth alternately by the
right and left arm.
Turning in place
•Put one hand on the handrim behind your hip and the other one in front of your hip.
•Push one wheel forwards and the other wheel backwards simultaneously.
•The greater the span between hands, the greater the turn.
Turning while riding
•Make more vigorous move forwards on the handrims with one hand.
•With a stronger turn, you can stop the wheel with one hand and with the other make more
vigorous move on the handrim forwards.
•Follow this rule also when moving backwards.

10
USAGE WITH THE HELP OF THE ACCOMPANYING PERSON
The wheelchair can be pushed by the accompanying person who holds hand grips placed on the
backrest. The accompanying person must obey the following rules:
•Before the ride, make sure that no user’s body part or piece of clothing is exposed to moving
parts o the wheelchair.
•When the user is not able to keep sitting position independently, stabilize the user using
stabilizing belt.
•The wheelchair should be pushed with both hands. When it is necessary to raise the front
wheels, press the lower grip of the frame with one foot and simultaneously pull the hand
grips towards you; lean over the wheelchair backwards.
•To stop the wheelchair, move the wheel lock lever (located at the rear wheels) towards the
front of the wheelchair until the wheel is locked (perceptible resistance). Repeat the action
with the other wheel. To release the wheel lock and allow further riding move the lever
towards the back of the wheelchair.
Note! While getting in or out the wheelchair, changing the user’s position or stop, the wheels must
be absolutely locked.
Note! Never leave the user in the wheelchair unattended (even with engaged wheel locks put) on
ramps and landings, etc.!
Riding down the step
•Ride up to the edge of the step and grab handrims.
•Pull both hand grips towards you and simultaneously press the tube of the frame with your
foot in order to lift front wheels.
•Keeping the wheelchair in this position, move the wheelchair carefully down the step and
push it forwards so that the front wheels touch the ground.
Riding up the step
•Place the wheelchair backwards to the step.
•Pull both hand grips towards you in order to lift the front wheels from the ground, and pull
the rear wheels over the edge of the step so that the front wheels can be placed on the
ground again.
TRANSPORT WITH HELP OF THIRD PERSON
Stairs
The help of at least two fit people is required in order to transport the user in the wheelchair. Any
obstacles which may pose a risk for the user or other people must be removed.

11
•To transport the wheelchair upwards or downwards, one person grabs hand grips and pull
the wheelchair towards him/her, slightly lifting front wheels.
•The second person grabs the frame from the front (remove the footrests for this purpose)
and assisting each other, pull or lower the wheelchair.
•Perform these activities smoothly and calmly with no sudden moves which may cause an
accident.
Note! Remember to protect the user properly by fastening the belts around user’s trunk.
Car
Note! Wheelchair users should not be transported in vehicles while in wheelchair. To travel safely,
the user should be secured in the seat of the car while the folded wheelchair should be placed in the
boot.
Note! Do not transport the wheelchair inside the car! It may pose a huge risk for the passengers in
case of car accident!
•To transport the wheelchair, fold it, and if necessary, dismantle the footrests and rear
wheels.
•If such, follow dismantle/assembly instructions given in this manual.
Ramps
In order to transport the user in the wheelchair on ramps, strictly follow the safety rules and act as in
case of transporting the user on stairs (see above).
Note! Follow the manufacturer’s recommendations of ramp and strictly comply with permitted
loads.

12
5. Technical data
Overall width
67.5 cm
Inner width
46 cm
Overall depth
125 cm
Seat height from the ground
48.5 cm
Overall height
123.5 cm (83.5 cm)
Seat dimensions
45 cm x 39 cm
Weight
21.5 kg
Maximum capacity
100 kg
Folded width
41 cm
Frame colour
silver
6. Notes and recommendations
Note! Check the condition of the wheelchair regularly and promptly contact with the retailer in case
of any damage that may raise doubts of the safety use of the wheelchair.
Note! Keep the wheelchair in dry places below 40oC and do not expose it to sun rays, water, dust,
sand, etc. The wheelchair must be properly protected (i.e. covered) and free from any external loads
while storage. Remember that the surface temperature of upholstery and frame components may
increase when exposed to the sun or other heat source, which may cause burns.
Note! Only use original spare parts admitted to operation by the manufacturer. For this purpose,
contact with the retailer.
Note! Do not make any repairs or modifications by yourself.
Note! Do not adjust the angle of the seat by yourself.
NOTE! Timago International Group does not bear responsibility of improper moving in the
wheelchair, failure to comply safety regulations and misuse.
7. Cleaning and maintenance
Reviews
Check the condition of the wheelchair regularly:

13
•Before each use: check the condition of mechanical components, correct assembly of
removable components, proper work of wheel locks, tyre condition, and proper unfolding of
the wheelchair.
•Every 4 weeks: check the condition of mechanical components including proper greasing,
wheel lock adjustment and seat condition.
•Every 6 months: it is recommended to do review at the service point indicated by the
manufacturer (according to the applicable service price list).
Cleaning and maintenance
Carry out the maintenance of the wheelchair components regularly:
•The upholstery can be cleaned with damp (not wet) cloth and cold or warm water, without
the use of detergents. Difficult stains can be cleaned with a sponge. Do not soak the
upholstery too much. Dry away from heat sources.
•Plastic elements should be cleaned with damp cloth possibly with the use of appropriate
detergents for plastic elements. In such case follow the instructions given by the producer
and safety measures.
•Empty and disinfect the toilet bucket and toilet seat after each use. Use cleaning agents
according to producer’s recommendations.
8. Warranty information
All products distributed by our company are under a warranty, the terms of which are described in
the warranty card received at the time of purchase. Please, keep in mind that for warranty purposes,
the proof of purchase (receipt or invoice) should be retained.
As a user friendly company, we only supply products which have been thoroughly tested with respect
to materials, quality and functionality.
Please contact us if you have any questions concerning our servicing procedure.

14
9. Labels
Reference number Manufacturer
LOT number Manufacture date
Serial number
Representative in Euro-
pean Union
Note
Please read the
instruction
The Manufacturer checked for compliance with essential
medical devices requirements.
10. Recommended products
Products offered by Timago International Group include:
Orthoses and joint stabilizers, anti-decubitus equipment and accessories
Manual and special-use wheelchairs
Walkers and rollators, crutches and canes
Rehabilitation beds, stabilizing and immobilizing belts
Ancillary and sanitary equipment, disposable medical equipment
Electro-medical equipment
Our complete line of products is available from our distributors. Learn more at: timago.com.
Manufacturer:
Timago International Group
Spółka z o.o. i Spółka – Spółka komandytowa
ul. Karpacka 24/12
43-316 Bielsko-Biała, Polska
T.: [phone]
F.: [phone]
E.: [email protected] q
Issue I, date 29.07.2016