Timberk SE1 VU Series User manual
Models /
SWHSE110VU
SWHSE115VU
SWHSE130VU
SWHSE110VO
SWHSE115VO
SWHSE130VO
with upper connection /
with bottom connection /
Instruction Manual
The manufacturer is entitled to modify design and colour scale of the device without any special notice.
.
Electric Storage
Water Heater
SE1 VU
SE1 VO
2www.timberk.com electric storage water heater
1. IMPORTANT INFORMATION
Please, read this instruction manual carefully prior to use of the water
heater.
This instruction manual contains important information concerning
your safety as well as recommendations on proper use of the appliance
and its maintenance. Save this instruction manual together with the
guarantee card, cash register receipt, cardboard box, if possible, and
packing material. Different types of this device are described in this
manual.
The water heater purchased by you may slightly differ from the one
described in the manual, but that does not affect its use and operation.
IMPORTANT SAFETY PRECAUTIONS AND INSTRUCTIONS CONTAINED IN
THIS MANUAL DO NOT INCLUDE ALL THE POSSIBLE MODES AND
SITUATIONS TO BE ENCOUNTERED. IT IS NECESSARY TO UNDERSTAND
THAT COMMON SENSE, CAUTION AND ACCURACY SERVE AS FACTORS
WHICH CANNOT BE 'BUILT IN' IN ANY PRODUCT. THESE FACTORS
SHOULD BE CONSIDERED BY A PERSON INTERESTED IN PROPER
OPERATION OF THE APPLIANCE. THE MANUFACTURER IS NOT
RESPONSIBLE FOR ANY DAMAGES OF THE APPLIANCE OR ITS PARTS
DURING TRANSPORTATION, CAUSED BY IMPROPER INSTALLATION,
VOLTAGE FLUCTUATIONS AS WELL AS WHEN ANY PART OF THE
APPLIANCE HAS BEEN CHANGED OR MODIFIED.
Dear customer!
We thank you for your happy choice! You've bought an electric storage
water heater Timberk with endmeled inner tank. It will serve you for a long
time.
Electric storage water heaters Timberk will provide you with a lot of water
and automatically maintain preset temperature. They are perfect to supply
with hot water country houses, cottages, baths and other personal service
rooms.
CONTENTS
1. Important information
2. Precautions
3. Performance characteristics
Main distinctive features
Technical characteristics
Dimensions
4. Water heater description
5. Delivery set
6. Water heater installation
Location
Water heater mounting
Connection to the water main
Connection to the electrical main
7. How to control water heater operations
8. Water heater control
9. Maintenance
10. Troubleshooting
11. Basic circuit diagram
12. Utilization
2
2
3
3
4
4
5
5
5
5
5
6
6
7
7
7
9
9
9
2. PRECAUTIONS
Certain precautions are to be observed upon use of the water heater.
Improper use due to ignoring precautions may harm health of the user
and other people as well as damage their property.
1. Any electrical appliance must be under control upon its use, especially
if there are children nearby. Make sure children do not touch the
appliance.
2. Prior to installation of the water heater, not connecting it to the
electrical main, check and make sure that the outlet for the water heater
has a ground contact and it is properly earthed. If there is no earth loop in
your electrical main then using of the water heater will be dangerous for
your life.
3. Connect the water heater only to 220V / 50Hz electrical main. If
necessary, find out parameters of your main at power suppliers.
4. To prevent overheating and risk of fire as well as damage of inner
electrical main do not modify the power cord's length and do not
connect the water heater through power extension cord.
3
www.timberk.com electric storage water heater
5. It is forbidden to switch on the water heater if it is not filled with water or
if water cannot go through the pressure safety valve.
6. Never use the water heater if it is damaged.
7. Do not remove the water heater cover when it is in operation.
8. Immediately unplug the water heater from the electrical main if strange
sounds, odour or smoke comes out from it.
9.Always unplug the water heater from the electrical main during
thunderstorm.
10. Prior to cleaning and maintenance of the water heater unplug it from
the electrical main every time. Cleaning and maintenance must be
performed in compliance with the instructions contained in this manual.
11. Do not use hazardous chemical substances to clean the water heater
and prevent their contact with the appliance.
12. To prevent electrical shock the damaged power cord must be replaced
only by qualified specialists in manufacturer's authorized service centres.
13. To prevent electrical shock do not place the power cord nearby heating
devices and flammable or combustible agents.
14. As temperature of water in the water heater can reach 75°C when it is in
operation you should not place your body parts under hot water upon the
first run. To prevent burns you should adjust the temperature of the
outflowing water.
15. Do not use the water heater for purposes not stipulated in this
instruction manual.
16. Do not use the water heater in an explosive or corrosive environment.
Do not store petrol and any other volatile flammable liquids near to the
appliance. It is very dangerous!
17. It is forbidden to make alterations in the design of the water heater or
modify it.
18. Any service works must be performed by a specialized organisation
and qualified specialists. Improper installation may cause voiding of
guarantee maintenance.
19. The water heater is not intended for use by children and persons with
reduced physical, sensory or mental capabilities, or a lack of experience
and knowledge unless they are under supervision or instructed on using
of the appliance by a person responsible for their safety. Children should
be controlled to ensure that they do not play with the appliance.
3. PERFORMANCE CHARACTERISTICS
Main distinctive features
1.Completely automatic control: automatic water heating, continuous
automatic water temperature control.
2.Protection system:
Drop Defense leakage protection and protection against excessive
pressure inside the tank (pressure safety valve);
HOT Defense two-level overheating protection (temperature detec-
tor and temperature limiter).
3.Steel inner tank with special protection coat from titanium finely-
divided glass enamel drown down by the modern method of electrostatic
dry enamelling is resistant to corrosion and boiler scale. Additionally,
enamel possesses increased adhesive capacity and high flexibility (heat-
treated at the temperature of 850°) that allow it to expand and shrink
upon temperature differentials in the same proportion as the walls of the
inner tank not forming micro-cracks in which corrosion pits can appear.
4.Pipes of heating elements are designed taking into account high
heating load: safe and reliable with increased service life.
5.The water heater is fitted with an anode rod for protection against
corrosion of the inner tank and decrease of boiler scale on the heating
element.
6.Inner urethane foam insulation of increased thickness allows for
effective retain of temperature of heated water and minimizes heat losses
decreasing power consumption of the water heater.
The water heater has simple design and it is convenient in service.
ENGLISH
l
kW
V
Mpa
_
_
mm
kWh/day
kWh
kg
Tank capacity
Operating power consuption
Rated voltage (AC)
Process pressure
Electrical protection class
Water protection class
Rated current
Appliance dimensions (HWD)
Constant daily loss
Factual year energy consumption
NET weight
Table 1
Technical characteristics of water heater are given below in Table 1.
Technical characteristics
ATTENTION!
Technical characteristics of the water heater you purchased
correspond to data specified in the table as of the date of
manufacture. Technical characteristics and delivery set can be
revised by the manufacture without any prior notice.
4www.timberk.com electric storage water heater
10
2
~220
0,75
I
IPX4
9,1
335335285
0,65
219
7,5
15
2
~220
0,75
I
IPX4
9,1
355355335
0,7
251,85
8,0
30
2
~220
0,75
I
IPX4
9,1
435435380
1
354,05
11,9
Product item of
Name Unit of
measuremen SWH SE1 10 VO
SWH SE1 10 VU SWH SE1 15 VO
SWH SE1 15 VU SWH SE1 30 VO
SWH SE1 30 VU
Model name Capacity, l
E
AFig. 2
B
C
D
Fig. 3
Fig. 1
A
100
100
100
100
100
B
70
70
95
120
C
170
170
170
170
170
E
66
66
66
66
66
66
SWH SE1 10 VU
SWH SE1 10 VO
SWH SE1 15 VU
SWH SE1 15 VO
SWH SE1 30 VU
SWH SE1 30 VO
D
82
82
92
132
10
15
10
30
15
30
100 95 170 92
132120
Table 2
Dimensions
Dimensions of water heaters (mm) are made in accordance with fig. 1, fig. 2
and fig. 3.
5. DELIVERY SET
1. Electric storage water heater 1 pc.
2. Pressure safety valve 1 pc.
3. Mounting strip for hanging/mounting of water heater 1 pcs.
4. Instruction manual 1 pc.
5. Guarantee card 1 pc.
6. Packing 1 pc.
6. WATER HEATER INSTALLATION
Location
1. The water heater of SWH SE1 VO series can be installed over a
washbasin, a kitchen sink or in any other place where it will not hinder
you. Please, note, that pipes must be placed on the bottom part of
water heater.
2. The water heater of SWH SE1 VU series can be installed under a
washbasin, a kitchen sink or in any other place where it will not hinder
you. Please, note, that pipes must be placed on the top part of water
heater.
3. Electric water heater should be mounted on a firm wall.
4. The wall where the electric water heater is to be mounted must
withstand at least the double weight of the water heater fully filled with
water. There must be no cracks and other damages on the wall.
Otherwise, it is necessary to take measures to strengthen the mounting or
install the water heater on a special support.
5. If a bathroom is too small the water heater can be installed in any other
place unexposed to direct sunlight and beyond the reach of moisture.
However, to reduce heat losses in pipelines the location where the water
heater is to be installed must be as close to the place of hot water use as
possible.
ENGLISH
5
www.timberk.com electric storage water heater
1. Power cord
2. Temperature controller handle
3. Inlet nozzle*
4. Outlet nozzle*
5. HEATING indicator lamp
6. Face panel cover
7. Back panel
8. Inner tank
9. Face panel
10. Temperature controller pipe
11. Heating element
12. Thermal insulation
13. Groove for the hanging/mounting of water heater
14. Magnesium anode
(through the example of SWH SE1 15 VO model)
* SWH SE1 VU series requires upper connection of water inlet and outlet; nozzles in this model are
located in the upper part of the water heater.
4. WATER HEATER DESCRIPTION
Fig. 6
Fig. 5
1
2
3*
Fig. 4
4*
5
6
8
9
7
10
11
12
14
13
13*
Water heater mounting
NOTE:
To install the water heater, please, use accessories provided by the
manufacturer. Electric water heater must not be mounted onto the wall
before you make sure that the mounting strip is installed firmly and
securely. Otherwise, the electric water heater may fall down from the
wall that may cause its damage and even more serious accidents
involving harm to health and personal injuries.
1. After you have chosen a proper place to install the water heater
determine points for holes for fixing of mounting strip, putting the strip
to a wall. Drill holes of corresponding depth in the wall using a drill
dimensionally fit for anchor bolts delivered together with the water
heater. Next, fix the mounting strip on a wall with help of screws. After
that you should mount water heater on a mounting strip (fig. 7).
2. Fasten an AC main socket to the wall. Requirements to the socket are
as follows: 220V / 10, single-phase, three wires. It is recommended to
place the socket from the right side higher of the water heater.
NOTE:
In the places accessible for water the AC electrical main socket must be
installed on a height of at least 1.8 m from the ground.
Fig. 7
Connection to the water main
1. The water heater must be connected to the water main with
minimum pressure of 0.1 MPa and maximum pressure of 0.7 MPa.
NOTE:
The water heater is the appliance operating in such a manner that
pressure of water in the water heater corresponds to the pressure of
water in the water main. If pressure in the water main exceeds 0.7 MPa
then it is necessary to install a pressure reducer before the water heater
so that pressure will not exceed 0.7 MPa.
2. To connect the water heater to the water main apply pipes with
diameter of G1/2.
3. To prevent water leakage when connecting pipes use rubber sealing
gaskets on the threaded pipe ends.
4. Screw the safety pressure valve onto the inlet nozzle marked with blue
colour and an arrow pointed water flow direction so that the water flow
direction coincides with direction of the arrow on the valve case.
NOTE:
Do not install additional accessories, such as a cut-off valve, between
the safety pressure valve and inlet nozzle.
5. Water heater with the mounted valve must be connected to the water
main install a shut-off valve at the water inlet point. You need to connect
a drain pipe to the opening of the pressure relief of safety valve. Next you
should put a drain pipe to the sewer.
6. Connect a desired number of consumption points to the outlet nozzle
marked with red colour.
7. Check leak tightness of joints: open the cut-off valve and one of the
outlet valves. After the tank is filled with water, as evidenced by outflow of
water from the outlet valve, turn off the outlet valve and check leak
tightness of all the joints.
6www.timberk.com electric storage water heater
ATTENTION!
If water in the location of installation contains a large amount of
calcium, manganese or ferric salts it is necessary to mount an
appropriate filter in the supply system to reduce the amount of
boiler scale in the tank and on the heating element.
Connection to the electrical main
ATTENTION!
Prior to connecting the tank water heater make sure that the water
heater is properly grounded. Proper grounding is important to
minimize electric shocks and risk of fire. The power cord is equipped
with a plug with a grounding pin. The appliance must be used with a
properly grounded power outlet. If the outlet you intend to use is
not properly grounded or grounded by a time-delay fuse or a circuit
breaker address to a qualified electrician to install a proper outlet.
1. The water heater is designed to be connected to 220V single-phase
electrical main. Prior to connecting make sure that parameters of the
electrical main in the point of connection correspond to the parameters
specified on the identification plate with technical characteristics of the
appliance. You should observe the current electrical safety code when
installing the water heater.
2. Power outlet must be designed for rated current of 10A at least; copper-
conductor power cord must be at least 3x1.5 mm2 in cross-section (for
copper). The power outlet and the plug must always remain dry to prevent
current leakage. Check regularly if the power plug is tightly connected to
the outlet. Do it in the following order: insert the power plug into the
outlet; in half an hour switch off the water heater and unplug the cord;
check by your hand if the plug is heated. If the plug is heated over 50°C
replace the outlet with a new one to prevent damages, accidents and fire
due to bad electrical contact. A specialist must do this.
ATTENTION!
To guarantee reliable operation and safe use of the water heater
check prior to the first run if it is properly connected to the 220V AC
electrical main. The water heater to be connected must be securely
wired up to the earth loop of your electrical main.
1. Thermostate handle
2. «HEATING» indicator lamp
8. WATER HEATER CONTROL
1. At first, open one of the outlet valves on the outlet of the water heater;
then open the inlet valve. The electric water heater will start filling in with
water. When water flows from the outlet valve freely it means that the
water heater is fully filled with water, and you can close the outlet valve.
Warning: During normal operation the inlet valve must be set open.
2. Plug the power cord into the outlet, after this the handle light will be on.
ATTENTION!
Power outlet must be designed for rated current of 10A at least;
copper-conductor power cord must be at least 3x1.5 mm2 in cross-
section (for copper).
7. HOW TO CONTROL WATER HEATER OPERATIONS
Control panel (fig. 8)
2
Fig. 8
1
ENGLISH
7
www.timberk.com electric storage water heater
ATTENTION!
Water can drip from the pressure safety valve upon heating. IT IS
IMPOSSIBLE TO AVOID DRIPPING AND IT IS FORBIDDEN TO
PREVENT IT BECAUSE IT CAN RESULT IN TANK RUPTURE (IN THE
CASE OF EQUIPMENT FAILURE). Working ability of the pressure
safety valve should be inspected every 14 days. The inspection
method is described in the section 9 (MAINTENANCE).
9. MAINTENANCE
1. Check the power plug and outlet as often as possible. Secure electrical
contact and proper grounding must be granted.T he plug and outlet must not
heat excessively.
2. If the water heater is not used for a long time, especially in regions with low air
temperature (below 0°C), it is necessary to drain the water heater to prevent
damage of the appliance (due to water freezing in the inner tank). To do so it is
necessary to:
- d isconnect the water heater from the electrical main;
- t urn the water off by the cut-off valve;
- open the hot water tap and drain the system.
3. Set the desired temperature of water by the temperature controller han-
dle by rotating the handle; HEATING indicator lamp (fig. 8) will flash on.
When water reaches the preset temperature HEATING indicator lamp will
go out. When water temperature drops to a certain level heating will be
switched on automatically and restore the required water temperature.
4. After rotating the handle to the position «MIN» the minimum tempera-
ture +30°C (± 5°C) would be seted. After puting the handle in to position
«MAX», the maximum temperature would be set +70°C (± 5°C).
5. There is a COMFORT sign on the panel. It signifies optimal temperature
of heating. Fixing the temperature controller handle in position COM-
FORT you choose the most efficient mode of electricity consumption.
6. To turn off the water heater set the switch handle to position « » and
unplug the power cord.
3. To ensure long-term reliable operation of the water heater it is recom-
mended to clean the inner tank regularly and remove deposits from the
electric heating elements of the appliance as well as check condition (fully
decomposed or not) of the magnesium anode and, if necessary, replace it
with a new one in case of full decomposition.
Frequency of tank cleaning depends upon hardness of water available in a
given territory. Cleaning must be performed by special maintenance
services. You can ask the seller for the address of the nearest service centre
or find it on the website .www.timberk.com
ATTENTION!
The manufacturer grants an extended guarantee for particular
water heater components provided that timely and proper routine
maintenance is performed by specialists of an authorized service
centre (see the guarantee card).
For S WH S E1 V O series:
- unscrew the back pressure safety valve screw and set the handle in horizontal
position; water will flow out from the pressure relieving opening (refer to the
figure 9).
For S WH SE1 V U series:
- disconnect the water heater from the water main and consumption point;
rotate it 180 degrees; water will flow out from the outlet nozzle.
It is possible not to drain the tank, but set the water heater on minimum heating
temperature with constant connection to electric supply.
ATTENTION!
Never drain the appliance if water temperature is over 50°C since it
may result in burns.
Screw
Pressure drop hole
Flow control handle Displacement of
water drainage
Fig. 9
8www.timberk.com electric storage water heater
5. The water heater is equipped with a temperature
limiter (figure 10) which cuts off power supply to the
heating element upon water overheating or its
absence in the water heater. If the water heater is
connected to the electrical main, but water does not
heats and the handle lamp does not light then the
temperature limiter was switched off or not switched
on. To reset the water heater to the operating condi-
tion it is necessary to:
- unplug the water heater from the electrical main, remove the face panel
cover;
- press the button located in the centre of the temperature limiter placed on the
heating element until it clicks;
- if the button cannot be pressed and there is no click then you should wait until
the temperature limiter cools down to the initial temperature.
Fig. 10
ATTENTION!
If these actions have no positive result or the temperature limiter turns
off repeatedly during a short period of time then you should unplug the
water heater from the electrical main, cut off water supply and contact
your local Timberk Authorized Service Centre for a consultation or
repair of the appliance.
ATTENTION!
If water does not flow then the valve is damaged. In this case you
must not use the heater; it is recommended to call for a service
technician.
7. Wipe external surfaces of the water heater by a damp cloth with soap
when necessary.
6. Bear in mind to check serviceability of the pressure safety valve every 14
days. The inspection method is as follows:
- turn the handle for draining to the upper position until you feel the
change of thread, then water must start flowing out from the valve
opening; after checking the water outflow return the handle to its initial
position.
4. Schedule maintenance should be performed under strict observance of this
instruction manual and safety precautions.
ENGLISH
10. TROUBLESHOOTING
All the disorders in operation of the water heater should be fixed as well
as putting of the appliance in long-term storage should be performed
in appropriate service centres. The water heater must be prepared for
long-term inactivity only by specially trained qualified specialists,
because improperly performed repair can result in hazard during water
heater operating.
You can ask the seller for the address of the nearest service centre or
find it on the website www.timberk.com.
Table 3 Possible malfunctions and troubleshooting methods
FAILURE POSSIBLE CAUSES REMEDIAL PROCEDURE
Indicator lamps do not
light, water does not
heats
Water does not flow
out from the hot water
tap
Water temperature is
too high
Water leakage
Water flows out from
the appliance case
Heating indicator lamp
lights, but water does
not heats
1. Temperature controlling device
is damaged.
2. Temperature limiter was
actuated or not switched on.
3. Temperature limiter is
damaged.
1. Address to a repair specialist, a Timberk
authorized service centre.
2. Switch the temperature limiter on in
accordance with the instruction on its
switching on.
. Address to a repair specialist, a Timberk
authorized service centre.
1. Water supply is cut-off.
2. Water pressure is too low.
3. Cold water supply valve is closed.
Water temperature control system
is damaged.
Seal at the point of pipe connection
is broken.
1. Breaking of inner tank (corrosion)
2. Seal at the point of the heating
element connection is broken.
1. Temperature controlling device
is damaged.
2. Insufficient time for heating.
3. Heating element is broken.
1. Wait until water supply is restored.
2. Switch the water heater on again when
normal water pressure restores.
3. Open the cold water supply valve.
Address to a repair specialist, a Timberk
authorized service centre.
Replace the joint seal.
Address to a repair specialist, a Timberk
authorized service centre.
1. Address to a repair specialist, a Timberk
authorized service centre.
2. Wait until water heats up.
3. Address to a repair specialist, a Timberk
authorized service centre.
9
www.timberk.com
11. BASIC CIRCUIT DIAGRAM
Fig. 11
12. UTILIZATION
Upon completion of service life of the water heater it should be utilized.
For detailed information about the water heater utilization, please, ask
local authorities. The life period of water heater is 15 years.
ATTENTION!
The manufacturer is entitled to make any changes in design of
the appliance that improve its technical and other characteristics.
These changes can be made without warning and any notice of
customers. The manufacturer is not responsible for changing of
the electric scheme of the appliance that can be made without
notification of the customer.
The tank water heater is not intended to be used by children, old or disabled
people without control. Make sure to use the water heater carefully, do not
switch between modes abruptly, follow closely recommendations set forth in
this instruction manual. Children nearby the water heater must be controlled
by adults and never use the unit as a playing element.
Transformer
I
Indication board
Power Board
10 www.timberk.com electric storage water heater
14www.timberk.com 11
www.timberk.com
!
.
imberk
. .
imberk
.
, ,
.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
11
11
12
12
13
13
14
14
14
14
15
15
16
16
16
17
18
19
19
20
1.
.
, ,
.
, , ,
.
.
,
.
,
,
,
. , ,
,
«» .
,
.
, ,
, ,
-
2.
,
.
,
.
1.
, ,
. ,
.
2. ,
, ,
.
.
( SWH SE1 VO)
1.
2.
3. *
4. *
5. «HEATING»
6.
7.
8.
9.
10.
11.
12.
13.
14.
* SWH SE1 10 VU, SWH SE1 15 VU SWH SE1 30 VU
.
4.
. 6
. 5
1
2
3*
. 4
4*
5
6
8
9
7
10
11
12
14
14
13
13*
5.
1. 1 .
2. 1 .
3. - 1 .
4. 1 .
5. 1 .
6. 1 .
6.
1. SWH SE1 VO
,
, ,
.
SWH SE1 VU
,
, ,
.
2.
3. , -
, , ,
, ,
.
.
4. ,
,
.
.
12www.timberk.com
3. 220 /50.
.
4. ,
,
.
5. ,
-
.
6. , .
7. .
8.
, , .
9.
.
10. -
.
.
11.
.
12. ,
-
,
.
13.
.
14.
75 ,
. -
.
15. , ,
.
16.
.
, !
17.
.
18.
,
.
.
19.
( ) ,
,
,
,
. , ,
.
3.
1. :
, .
2. :
- Drop Defense -
( )
- HOT Defense - (
)
3.
,
,
.
( 850°),
,
, ,
.
4.
:
.
5.
.
6.
,
13
www.timberk.com
E.
. SWH SE1 10 VO
SWH SE1 10 VU SWH SE1 15 VO
SWH SE1 15 VU SWH SE1 30 VO
SWH SE1 30 VU
,
.
7.
.
1
1.
!
.
.
()
()
-
-
/
10
2
~220
0.75
IPX4
I
9.1
335335285
0.65
219
7.5
15
2
~220
0.75
IPX4
I
9.1
355355335
0.7
251.85
8.5
30
2
~220
0.75
IPX4
I
9.1
435435380
1
354.05
11.9
E
A. 2
B
C
D
. 3
. 1
A
100
100
100
100
100
B
70
70
95
120
C
170
170
170
170
170
E
66
66
66
66
66
66
SWH SE1 10 VU
SWH SE1 10 VO
SWH SE1 15 VU
SWH SE1 15 VO
SWH SE1 30 VU
SWH SE1 30 VO
D
82
82
92
132
10
15
10
30
15
30
100 95 170 92
132120
2
( )
. 1, 2, 3 2.
14www.timberk.com
( SWH SE1 VO)
1.
2.
3. *
4. *
5. «HEATING»
6.
7.
8.
9.
10.
11.
12.
13.
14.
* SWH SE1 10 VU, SWH SE1 15 VU SWH SE1 30 VU
.
4.
. 6
. 5
1
2
3*
. 4
4*
5
6
8
9
7
10
11
12
14
14
13
13*
5.
1. 1 .
2. 1 .
3. - 1 .
4. 1 .
5. 1 .
6. 1 .
6.
1. SWH SE1 VO
,
, ,
.
SWH SE1 VU
,
, ,
.
2.
3. , -
, , ,
, ,
.
.
4. ,
,
.
.
:
,
, .
,
,
.
,
.
1.
,
, .
,
. ,
(. 7)
2. .
: 220 V/10A, , .
.
:
, ,
1,8 .
. 7
1.
0,1 , 0,75
:
,
, ,
.
0,75 ,
,
0,75 .
2.
G1/2.
3.
.
4.
,
. -
(. . 9)
( ) .
:
, ,
.
5.
-
.
6. , ,
.
7. :
. ,
,
.
15
www.timberk.com
!
, ,
.
!
,
.
.
, .
.
, ,
,
.
1.
220 . ,
,
.
.
2.
10A,
2
31,5 ( ).
.
,
. :
,
,
, .
50°, , ,
. .
!
-
220 .
.
7.
( SWH SE1 VO)
!
-
10,
31,5 ² ( ).
1.
2. «HEATING»
8.
1. -
, . -
. -
, , -
. :
.
2. , -
.
2
. 8
1
16 www.timberk.com
!
.
,
(
). -
14
9 ().
3.
, -
,
( ) ,
, -
.
,
. -
.
www.timberk.com.
SWH SE1 VO:
-
,
. (. . 9)
SWH SE1 VU:
-
;
- 180°
.
,
, -
.
! º
, 50 ,
.
Винт
Отверстие сброса давления
Ручка слива Положение
слива воды
. 9
17
www.timberk.com
3. -
, -
, «HEATING» (. 8).
,
«HEATING» , ,
-
.
4. «MIN», -
+30 º (±5 º),
«MAX»,
+70 º (±5 º).
5. «COMFORT» -
. -
«COMFORT»,
.
6. -
« » ,
.
9.
1. .
,
.
.
2. ,
( 0ºC),
( -
),
, :
-
-
-
!
(. ).
5.
(. 10),
,
.
,
,
.
:
- ,
- ,
,
- , ,
. 10
!
-
, ,
, -
Timberk
.
6.
14 - :
-
.
.
4.
.
3
!
, .
.
7.
.
10.
. -
,
.
www.timberk.com.
,
,
1.
.
2.
.
3.
.
1.
Timberk .
2. ,
(. 18, .5).
1.
2.
3.
.
1.
()
2.
1.
.
2.
3.
1.
.
2. ,
.
3.
.
.
2. .
3.
Timberk.
Timberk.
Timberk.
1.
Timberk.
3.
Timberk.
18 www.timberk.com
11.
. 11
12.
-
.
. -
15 .
!
,
.
.
,
.
-
, -
. , -
, , -
. ,
, ,
, .
Термостат
Индикаторная лампа
Нагревательный
элемент
Ограничитель
температуры Трансформатор
Плата индикации
Силовая плата
19
www.timberk.com
13.
EEC 89/336, -
,
.
.
Timberk ,
Timberk , -
, ,
-
: . RU.0001.11AB71
«».
: 123308, . , . , . 3, . 1, .
323; : 115162, . , .,
28, 4, . +7 495 6044266, +7 495 6044266
.
,
:
P 60335-2-35-2000
P 51318.14.1-2006 .4
P 51318.14.2-2006 p.5,7
P 51317.3.3-2008
P 51317.3.2-2006 p.6,7
: RU C-IL.AB71.B.00051
.
,
: 09.02.2012 08.02.2015
, ,
. * , ,
\ \ .
, ,
.
:
« » , 10,
, 88000
/ +972-8-637-88-311
*:
«»
: , 111024, . , . 5- , .2, . 1
: +7 499 653 7356
: + 7 (495) 6275285
20 www.timberk.com
This manual suits for next models
7
Table of contents
Other Timberk Water Heater manuals
Timberk
Timberk SWH FSL1 30 V User manual
Timberk
Timberk Grande Pro Series User manual
Timberk
Timberk RE9 30 V User manual
Timberk
Timberk SWHFS130V User manual
Timberk
Timberk WHEL-6 OC User manual
Timberk
Timberk SWH RES 150V User manual
Timberk
Timberk SWH RS1 30V User manual
Timberk
Timberk T-WI3-P10-SC User manual
Timberk
Timberk SWH RE19 30 V User manual
Timberk
Timberk WHN-4OS User manual
Timberk
Timberk RS1 Series User manual
Timberk
Timberk Optima FS47 V Series User manual
Timberk
Timberk SWH ME2 10 V User manual
Timberk
Timberk SWH FSL3 30 VH User manual
Timberk
Timberk Intelligent FS51D V Series User manual
Timberk
Timberk T-WSS30-N40D-V User manual
Timberk
Timberk T-WSS30-N77-U-WF User manual
Timberk
Timberk SWH RS1 30 VH User manual
Timberk
Timberk SWH RE7 225 V User manual
Timberk
Timberk Lotta FS1D V Series User manual
Popular Water Heater manuals by other brands
Atlantic
Atlantic CALYPSO manual
Raypak
Raypak B0147 Owner's guide and installation instructions
Toyotomi
Toyotomi BS-36UFF Operating and maintenance instructions
Premier Equestrian
Premier Equestrian Water Wagon Setup guide
STIEBEL ELTRON
STIEBEL ELTRON SN 5 S Operating and installation instructions
Sinclair
Sinclair SWH-200DE Service and installation manual
Ariston
Ariston PRO1 ECO Series user manual
clage
clage CEX-U Installing instructions for the professional
Garanterm
Garanterm ES 50-H user manual
STIEBEL ELTRON
STIEBEL ELTRON DHC-E 3/3.5-1 Trend Operation and installation manual
Haier
Haier ES10V-Q1 Service manual
fothermo
fothermo PSU-12 Installation and operation instructions
