Timberkits Pianist User manual

Pianist

1
(UK) Symbols in these instructions. (FR) Symboles des instructions. (ESP) Simbolos en estas instrucciones. (IT) Simboli
in queste istruzioni. (Ger) Symbole in dieser anleitung
(UK) Waiting time.
(FR) Temps d’attente.
(ESP) Tiempo de espera.
(IT) Tempo d’attesa.
(DE) Wartezeit.
(UK) Glue.
(FR) Coller.
(ESP) Pegar.
(IT) Incollare.
(DE) Leimen
(UK) Don’t glue.
(FR) Ne pas coller.
(ESP) No pegar.
(IT) Non incollare.
(DE) Nicht leimen.
(UK) Glue guard. Prevents glue getting between moving parts during build. Remove after 2
minutes.
(FR) Piece de protection contre la colle. pendant l’assemblage, eviter tout depôt de colle sur les
pieces en mouvement. Enlever apres 2 minutes.
(ESP) Parte de protection de el pegamento. durante la fase de esambalje, evitar que el pegamento
se ponga sobre partes que se mueven. Quitar despues de dos minutos .
(IT) Pezzo di protezione della colla. Durante l’assemblaggio evitare che la colla vada su parti non
statiche . Imuovere dopo due minuti.
(DE) Karton. Verhindert das eindringen von leim zwischen die bewegliche teile während der
montage. Zwischen die beweglichen Teile.
(UK) Wax surface to lubricate.
(FR) Appliquer la cire sur cette
surface.
(ESP) Aplica la cera sobre esta su-
percie.
(IT) Applicare la cera su questa
supercie
(DE) Wax Oberäche zu schmieren.
Helpful hints/conseils utiles/consejos utiles/suggerimentutili/nützliche tipps
(UK) Check all parts present in trays
(FR) Vérier que toutes les pièces soient présentes dans les bacs
(ESP) Controlar que hay todas la partes en la caja
(IT) Controllare tutte le parti presenti nel kit
(DE) Bitte prüfen sie, ob alle benötigten teile vorhanden sind
(UK) Read all instructions and look at all diagrams
(FR) Lire toutes les instructions et regarder toutes les gures
(ESP) Leer las intrucciones y guardar a los diagrames
(IT) Leggere tutte le istruzioni e guardare i diagrammi
(DE) Lesen sie alle anweisungen und betrachten sie die schaubilder
(UK) Check assembly before gluing
(FR) Vérier le montage avant collage
(ESP) Controlar el montaje antes de empezar a pegar
(IT) Controllare l’assemblaggio prima di incollare
(DE) Montage prüfen vor dem einklebern
(UK) Some parts may need sanding
(FR) Certaines pièces nécessiteront d’être poncées.
(ESP) Algunas parte necesitan de ser suavizadas
(IT) Alcune parti potrebbero aver bisogno di levigatura
(DE) Möglicherweise müssen manche teile geschlien werden
Colouring tips/conseils concernant l’application de peinture/ consejos para Pintar/ suggerimenti per colorare/
lackiertipps
(UK) Do not apply paint to parts which move against one another. It is easier to paint some parts before
assembling
(FR) Ne pas appliquer de peinture sur les parties qui se déplacent l’une contre l’autre. Il est conseillé de pein
dre avant assemblage
(ESP) No aplique la pintura sobre las partes que se tocaran. Resulta mas facil pintar las partes antes de montar.
(IT) Non applicare la pittura su quelle parti dove ce attrito con un’altra parte. è piu semplice pitturare alcune
parti prima della fase di assemblaggio.
(DE) Teile, die aneinander reiben, sollten nicht lackiert werden. Fertig lackierte teile sind o leichter zu
montieren
Visit our website to view
instructional videos where you
see this symbol.
www.timberkits.com
!
Pay special attention to this
section.
New Symbols in our
Instructions

2
Or visit our website for tips, advice and instructional videos.
All these can be found in Resources/Advice Videos on our website.

2
46
5x108mm
7
1
3
16
37 x2
32 24 x2

3
4
2mmx12mm
3mmx12mm
3mmx15mm
2mmx25mm
3mmx24mm
3mmx24mm
3mmx36mm
3mmx40mm
3mmx92mm
3mmx114mm
3x76mm
5mmx114mm
6mmx147mm
5mmx32mm
6mmx25mm
3mmx36mm
5
47
12 x2 12 x2
12 x2 12 x2
11 x2 12 x2
11 11 x2
8 8 9 9
26 22
44 38 x2
39 x3
39 x3
13
45
23
42
43
40 x2
20
31
10
6
6 6 6 6 6 6 6 6 66 6 6 6 6 6

4
18
18
18
17
17
17
35 & 36
33 & 34
25
2 x2
28
30
41
27
29
15
14
19
21

1
10mins
2
5mmx108mm
1a
5
1b
22a
1
3
2
4
5
3mmx114mm
5mmx114mm
2b
20mins
4
5
Parts 4 and 5 used for
aligning part #2 only at
this stage.

6
2c
6 (x16)
3
5mmx32mm
7
8
8
3a
3b
Sand any rough pieces from around
the hole on each piano key before
sliding onto the 3mm x 114mm
bamboo.

7
5a
4
6mmx25mm
6mmx147mm
9
10
11
x2
12
x5
11
x1
13
x1
12
x5
11
x2
5
3c
3 cont
10mins
Round o outer edge of
part #13 and then wax
before using
13

8
5b
6
9
11 11 12 12 12 12 12 11 13 12 12 12 12 12 11 11
11 11 12 12 12 12 12 11 13
12 12 12 12 12 11 11
6a
6b
10mins
10mins
Push all cams to one side and move and glue one at a time above a corresponding key. Vary the position of the at
sides of the No. 12 cams.

9
77a
7b
10mins
20mins
8
8a
10mins
8b
14
15 16
17
18
Glueing sequence
14 15 16
Attach parts 14, 15 and 16 to the back of the
piano whilst the glue is still drying so that
you can adjust to t.

10
20mins
20
19
3mmx12mm
3mmx36mm
3mmx24mm
9
9a
21
9b
3mmx12mm

11
10a
10b
10c
22
23
24
24
10
11
25
26
27
28
10mins
10mins
11a 11b
3mmx12mm

12
12
20mins
12a 12b
29
13a
13
13b
30

14
13
3x36mm
13c
3mmx76mm 31
13cont
14a
14b This will be glued in place nally on page 17.
15
38
39
39
39
40
37
37
2mmx25mm
2mmx12mm
15a 15b
40
38
39
39
39
Sand and wax each nger and thumb.
2mmx25mm
2mmx12mm

14
16
15c 33
34
35
36
10mins
10mins
10mins
15d
32
Ensure Part No. 32 runs inline with the piano
keys and is positioned in front of cam No. 13.

15
20mins
18
19 19a 19b
3mmx24mm
41
42
17
20mins
3mmx12mm
3mmx12mm
Glue the arms in place so that the ngers are
resting completely at on the piano keys.

16
20
20mins
19b
20a
20b 20c 20d
20e
43
44
45
3mmx40mm
3mmx15mm
3mmx12mm
Glue part No. 45 onto the 11th key from the handle
end.
When glue is dry check keys either side are not
glued to the 11th key.
Twist the head to a jaunty angle whilst glue is still drying.

17
21
21a
(21b) Whilst glue is still drying on 3x76mm rod
turn the model the right way up and carefully
turn the handle.
The pianist should raise his hands up from the
keyboard by about 10mm.
Adjust 3x76mm rod in and out of part No 31
to suit.
(21c) Part No 7 is held in position by the 2 spac-
ers (part No’s 8). Ensure part No 7 is in position
in line with cam 13 before gluing spacers. Part
No. 7 should be free to pivot on the 5x114mm
rod.
3mmx15mm
21b
21c

22 22a 47
46
3mmx92mm
22b
22c
18