Time4Sleep FRANCES OTTOMAN LIFT UP BED User manual

Parts Identification
Parts Checklist
Page 1 of 9
200815
PLEASE READ
this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be kept
away from young children during assembly, to avoid the
danger of choking.
IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - PLEASE READ THESE INSTRUCTIONS CAREFULLY.
Qty Qty
Ref. Description DescriptionRef.
1
2
3
4
12
6
5
8
9
1
1
1
1
2
5
1
2
1
13 1
7 2
Headboard
Footboard
Side Rail - Left
Side Rail - Right
Mattress Base Board - Headend
Mattress Base Board - Footend
Storage Base Boards
10 2
11 1
14 1
Base Board Support Rails (Wood)
Mattress Base Support Rails
Corner Brackets
Mattress Base Lifting Handle
Feet for Headboard
Feet for Footboard LH
Feet for Footboard RH
8
7
7
5
6
11
1
2
3
4
10
9
12
13
12
14
FRANCES OTTOMAN
LIFT UP BED

QtyCode Description
Ax16
Fittings Checklist
C
D
Flat Washers (for M8 bolts)
Qty
Code Description
Allen Key (for M8 bolt) x1
H
K
x8
x4
Bolts (M8x30mm) for fitting
corner brackets (10) to footboard (2)
and side rails (3&4) and also fitting side
rails toheadboard & footboard (1&2).
Bolts (M8x45mm) for
Bolts (M8x60mm) for
fitting feet (12,13&14) to
fitting mattress base
support rail (9) to
headboard & footboard (1&2)
)2&1(draobtoof&draobdaeh
Qty
HARDWARE FOR FITTING MATTRESS BASE BOARDS (PACK B)
F
G
J
x1
Spanner (for M8 nuts)
Metal Plates for connecting
mattress base boards (5&6)
x2
E
HARDWARE NEEDED FOR BED ASSEMBLY (PACK A)
x28
Code Description Qty Code Description
Page 2 of 9
CFlat Washers (for M8 bolts) x16
LFlat Washers (Black）x4
x16
Spring Washers (for M8 bolts)
B
Ax16
Bolts (M8x30mm) for fitting
gas-lift mechanism and metal
connecting plates
(J) to
mattress base boards (5&6).
x12
Spring Washers (for M8 bolts)
B
Flange Lock-Nuts (M8)
for gas-lift pistons.
x2
x2
Black domed nuts (M8) for fitting
mattress base lifting handle (11) to
mattress base board (6).
Additional Tools Required
Care & Maintenance
Please retain your assembly instruction and
tools provided for future use.
Periodically check that all bolts are still tight.
General Hints & Tips
A ssembly requires two persons.
Approximate time to
assemble this product
1.5 Hrs
No Additional Tools Required
In the unlikely event of missing or damaged parts,
please contact your retailer. Please have this guide at
hand quoting the part code reference numbers shown
when requesting spare or replacement parts.
Please Note: Domed Nuts 'E' & Flat Washers 'L' are pre-fitted to Lifting Handle (Part 11)

Page 3 of 9
Stage
2
Bed Assembly - Use Pack 'A'
x8 B x8A C x12
Dx1
Stage
1
x8
HC x8
Dx1
K
ABC
C
2
9
1
12
12
1
2
13
14
x4K
ABC
K
C
9
CBAD
10mm
I
C
H
D
H
H
C
C

Page 4 of 9
Stage
3
Bed Assembly - Use Pack 'A'
Stage
4
Dx1
1
2
3
4
D
34
&
12
&
90%
2
10
3
A
BC
4
&
44
3
2
DO NOT TIGHTEN BOLTS YET
x8 B x8A C x12
Dx1

Page 5 of 9
Stage
5
Stage
6
Base Board Assembly
8
34
&
7
8
100%
Carefully fit the wooden storage base board
support rails being careful not to damage the fabric
on the internal face of the side rails.
Make certain the bed is squared up as shown in the
diagram then tighten all bed assembly bolts 100%.

Page 6 of 9
Gas Lift Assembly
Stage
7
ii) Lift up mattress base board support bars.
i) Untie the two mechanisms.
SMALL GAP
F
G
G
G x2
Fx1
Hold up each arm and slide piston stem onto the threaded axle and
fit loc-nut (G) using spanner (F).
Note, do not over-tighten - a small gap needs to be left - see sketch.
iii) Connect the piston stems

Page 7 of 9
Mattress Base Assembly - Use Pack 'B'
Stage
8
x8 B x8
A C
J
x8
x2
Dx1
5
A
A
D
D
B
C
C
J
5
BEFORE FITTING FOOTEND BASE BOARD (6) FIT BOTH PLATES (J) TO HEADEND BASE BOARD (5) AS SHOWN
SLIDE HEADEND MATTRESS BASE BOARD (5)
UP AGAINST THE LIFTING ARM STOP PLATES.
CAREFULLY SCREW x4 BOLT SETS INTO BASE
BOARD AS SHOWN - DO NOT TIGHTEN 100% YET.
5

Mattress Base Assembly - Use Pack 'B'
x8 B x4
A C x8
Dx1
Page 8 of 9
Stage
9
6
A
C
A
D
B
C
A
B
C
100%
SLIDE FOOTEND MATTRESS BASE BOARD (6) INTO POSITION
LOOSELY CONNECT (6) TO THE PLATES THEN SCREW OTHER x4 SETS OF BOLTS INTO PLACE
WHEN ALL x16 BOLT SETS ARE IN PLACE, MAKE SURE SIDES OF BASE BOARDS ARE IN
LINE WITH EACH OTHER, THEN TIGHTEN ALL BOLTS 100%
5
5
6

NOTE: Before fitting the mattress on top of the mattress base, carefully lower the base holding the handle
firmly and if necessary hold base horizontal, then place mattress on top. Be careful, without a mattress in
place the base may lift on its own and speed of movement is quick and may cause injury.
Depending on the weight of the mattress, the raising & lowering speed will vary so be careful until you get
used to the speed. Always use the handle to lift or lower the frame - keep fingers well away from the moving
parts.
When fully assembled and with the mattress in position, please raise & lower the ottoman 4/5
times to ensure the gas pistons are fully lubricated.
Page 9 of 9
Note: Be very careful what you
store under the bed - the top of
an item, like a suitcase or a box,
must not touch the underside of
the mattress base or it may get
damaged.
Maximum item height is 210mm.
Warning.!
Stage
10
Base Board Assembly
7
E x2
F x1
Lx4
FE
L
L
9
6