Time4Sleep SEVILLE OTTOMAN User manual

Parts Identification
Parts Checklist
Page 1 of 9
200224
PLEASE READ
this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be kept
away from young children during assembly, to avoid the
danger of choking.
IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - PLEASE READ THESE INSTRUCTIONS CAREFULLY
FABRIC
HANDLE
5
Ref. Qty
Ref. Description
Metal Slat Frame 1
4
SEVILLE OTTOMAN BED
Qty
1
2
3
Headboard
Footboard
Side Panels
1
1
2
Description
4
1
2
3
3
4
7
8
6
7
8
2
1
1
Angle Brackets
Mattress Stoppers
Fabric Base Cover
'U' Shaped Cross Bar
5
5
5
5
6
.
.
.
.

F x6
Fittings Checklist
Page 2 of 9
QtyCode Description
A
x24
C
x24
Spring Washers (for M8 bolts)
Qty
Code Description
B
Spring Washers (for M8 bolts)B
Bolts (M8x30mm) for
fitting side panels (3)
to headboard & footboard (1&2).
Flat Washers (for M8 bolts)
Hx1
Spanner (for M8 nut)
L
M
x4
x2
x6
x6
E
HARDWARE NEEDED FOR BED ASSEMBLY (PACK B)
HARDWARE NEEDED FOR FITTING GAS-LIFT MECHANISMS (PACK A)
x24
CFlat Washers (for M8 bolts) x16
)CKCAP(EMARFTALSLATEMGNITTIFROFERAWDRAH
QtyCode Description Qty Code Description
x2
G
x4
K
Screws (4x45 for fitting
'U' shaped cross bar (
8)
to side panels (3)
Bolts (M8x50mm) for fitting
mechanisms (J)
metal slat frame (4) to gas-lift
Bolts (M8x20mm) for fitting
metal slat frame (4)
metal connection plate (M) to
Nuts (for M8 slat frame bolts)
Flange Lock-Nuts (M8)
for gas-lift pistons
J (a)
Gas-Lift Mechanisms
x1
x1
J (b)
Spring Washers (for M8 bolts)
B
A
x8
Bolts (M8x30mm) for
fitting gas-lift mechanisms (J)
to headboard & footboard (1&2).
x8
CFlat Washers (for M8 bolts) x8
QtyCode Description Qty Code Description
D
Allen Key (for M8 bolt)
x1
Additional Tools Required
Care & Maintenance
Please retain your assembly instruction and
tools provided for future use.
Periodically check that all bolts are still tight.
General Hints & Tips
A ssembly requires two persons.
Approximate time to
assemble this product
1.5
Hr
In the unlikely event of missing or damaged parts,
please contact your retailer. Please have this guide at
hand quoting the part code reference numbers shown
when requesting spare or replacement parts.
Cross-head Screwdriver Tape Measure
Metal Connection Plates

1a
Ax16 B
x16 Cx16
J (a)
x1
Dx1
Page 3 of 9
CHOOSE WHICH SIDE YOU WANT TO LIFT UP
J (b)
x1
CHECK THIS DIAGRAM AND IF ACCESS IS NEEDED
FROM LEFT SIDE OF BED, FIT BOTH LIFT MECHANISMS
TO RIGHT SIDE OF THE BED. BOLT INTO THE HOLES
MARKED (R) WITH BLUE LABELS.
THE MECHANISMS ARE LABELED J (a) & J (b) PLEASE
CAREFULLY FOLLOW THE DIAGRAM BELOW.
LIFT FROM LEFT
Fitting Gas-Lift Mechanisms - Use Pack 'A&B'
Stage
J(b)
B
A
C
D
J(a)
12
R
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
BLUE
R
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
L
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
R
F
I
T
H
E
R
E
BLUE
ALIGN MECHANISMS WITH BLUE LABELS
BOLTS SHOULD BE IN CENTRE
OF LONG HOLES
A
BC
10mm

Stage
1b
Ax16 B
x16 Cx16 Dx1
Page 4 of 9
J (a) x1 J (b) x1
CHECK THIS DIAGRAM AND IF ACCESS IS NEEDED
FROM RIGHT SIDE OF BED, FIT BOTH LIFT MECHANISMS
TO LEFT SIDE OF THE BED. BOLT INTO THE HOLES
MARKED (L) WITH RED LABELS.
THE MECHANISMS ARE LABELED J (a) & J (b) PLEASE
CAREFULLY FOLLOW THE DIAGRAM BELOW.
LIFT FROM RIGHT
Fitting Gas-Lift Mechanisms- Use Pack 'A&B'
1
J(a)
J(b)
2
RED
ALIGN MECHANSIMS WITH RED LABELS
B
A
C
D
BOLTS SHOULD BE IN CENTRE
OF LONG HOLES
A
BC
10mm

Stage
2
Bed Assembly - Use Pack 'B'
D
x1
1
2
3
3
A x16 B x16 C x16
D
x1
K
x4
Stage
3
K
3
8
8
Page 5 of 9
.
.
.
.
1
2
&
3
4
&
D
90%
Make certain the bed is squared
up as shown in the diagram then
tighten all bed assembly bolts 100%.
ABC
D
1&2
3
6

Bed Assembly
Stage
4
Page 6 of 8
7
Stage
5
Turn the bed on its side and using the velcro tape
attach the Fabric Base Cover (7) carefully to the
bottom of the side-panels, headboard & footboard.
Make sure fabric is fitted evenly all round.
Fitting Slat Frame - Use Pack 'C'
Cx4
D
x1
x2
M
L
x4
D
C
L
M
4
4
4

HOLD THEM FORWARD
Slat Frame Support Bar
1&2
Fitting Slat Frame
Page 7 of 9
Stage
6

PLEASE NOTE: MAKE SURE THE HOLES FOR
MATTRESS STOPPERS ARE ON THE CORRECT SIDE
OF THE SLAT-FRAME BEFORE BOLTING TOGETHER.
H x1
B x6 C x12
D
x1
x6
F
x6
E
D
E
C
F
B
C
H
Page 8 of 9
Stage
8
Stage
7
H x1
D
x1
ii) Using two bolt sets on each side, (E),
(C), (B) & (F), loosely fix slat frame to
six holes - finger tight.
Bolt into centre of long holes
i) With help, lift Slat Frame (4) onto slat
frame support bars.
10mm
Hold frame then tighten all six bolt sets 100% using spanner (H) & Allen key (D).
Carefully lay frame down. Make sure there is an even
gap each side of about 10mm, as in the sketch.
4
Fitting Slat Frame - Use Pack 'C'
.
.

Stage
9
Page 9 of 9
Stage
10
G
H
G x2 Hx1
Slide gas-lift piston stem onto the axle
then fit the flange lock-nut (G). Tighten nut
with spanner (H) - do not over-tighten.
A small gap must be left so stem can
move freely - see sketch below.
Push x2 Mattress Stoppers (6) into metal frame.
Note: Place mattress on slats then slowly push down metal frame ensuring the frame is
aligned with the side panels. Depending on the weight of the mattress, the speed of the lift
will vary so be careful until you get used to the speed.
Always use the fabric handle to lift or lower the frame - keep fingers well away from the
moving parts.
6
Fitting Slat Frame - Use Pack 'C'
SMALL GAP
Note: Be very careful what
you store under the bed -
the height of the item, like
a suitcase or a box, must
not touch the slats or they
shall be damaged.
m m 0 9 1