Time4Sleep SORRENTO MIRROR DRESSING TABLE User manual

Page 1 of 5
PLEASE READ this sheet prior to assembly to familiarise
yourself with the various stages of construction.
Carefully open the pack supplied and check the contents
against the parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in
a safe and environmentally friendly way.
210312
1
2
3
2
3
SORRENTO MIRROR
DRESSING TABLE
Warnings
Parts Identification
Do not place very hot or very cold items on
the furniture unless table mats are used to
prevent such items coming into direct contact
with the glass.
Do not strike the glass with hard or pointed
objects.
Do not use abrasive cleaners on the glass as
these may scratch and damage the glass.
To clean your item, use a soft cloth, slightly
dampened with water, and wipe clean. If
necessary, use a few drops of washing up liquid
on the cloth.
Then buff with a dry, clean cloth.
If the glass is chipped or broken and unsafe
to use, please contact your retailer.
Do not drag the cabinet across the floor, lift it
into position using two persons.
Care & Maintenance
In the unlikely event of missing or damaged parts,
please email [email protected]
Please have this guide at hand quoting the part
code reference numbers shown, when requesting
spare or replacement parts.

Page 2 of 5
Fittings Checklist
Parts Checklist
Ref. Qty
1 1
Description
Dressing Table
3 2RH legs
22
LH legs
QtyRef. Description
Ex2
x2
F
Cable ties
Qty
Ref. Description
x8
B
Bolts
x8
C
x8
A
Flat washers
Allen key
Dx1
Spring washers
Brackets for furniture
- pre-fitted by the
factory.
Brackets for wall x2
G
Stage
1
Additional Tools Required
Cross-head Screwdriver
i) Open one of the top drawers
ii) Undo the screws and reverse
the knobs re-fitting them on the
outside of the drawer fronts.
Repeat on the second drawer.
Reversing the knobs
The knobs are mounted inside of the drawers
to protect them during transit

Removing the drawers
Remove the drawers carefully
as per illustrations.
Page 3 of 5
Stage
3
Stage
2
x
iii) Make sure the ferrule (x) is re-fitted
inside the holes, this is to prevent
cracking the glass - please do not
over-tighten the screws.
Repeat on the two lower drawers.
Re-fitting the knobs
This is to enable legs (2 & 3) to be fitted

Attach legs 2 & 3 to base of the dresser using bolts (A), spring washers (B) and
flat washers (C), follow the diagram so the angles on the legs are placed
correctly. Use Allen key (D) to tighten the bolts evenly, do not over-tighten.
Please note that there is label on each leg that needs to be aligned with labels on
the base of the dresser. They need to align and match with each other.
Stage
4
Page 4 of 5
Turn the unit upright, align the drawer runners and carefully slide
the drawers back into the unit then lift the dresser into position.
Note: we recommend that two people do this.
It is very important to always lift your furniture off the floor when
moving it, never drag it as this can damage your flooring, the
dresser legs and the cabinet joints.
1
3
2
3
2
A
BC
Stage
5
Carefully turn the dresser upside down making sure the
small drawers don't roll out and get damaged.
Fitting the legs
Re-fit the drawers

Assembly completed
Stage
6
Page 5 of 5
Fitting instructions for anti-tilt brackets.
We advise that to prevent any entrapment or unforeseen accidents, you need to secure the furniture to your
wall in accordance with the following instructions. This is to prevent personal injury or property damage from
unexpected tipping over of the product, especially recommended when there are children in the home.
FURNITURE
(E)
WALL FURNITURE
1. The brackets (E) are pre-fitted to the furniture by the factory.
2. Position your furniture in the room deciding where on the wall the brackets (F) needs to be located -
they need be close to, and in-line with (E) so they can be linked together. With help, lift and move
furniture aside and place bracket on the wall and mark position of the 4 screws with a sharp pencil.
3. Fix brackets to the wall using suitable wall fixings, remember that screws and wall fixings are not
included. Seek professional advice if unsure about a safe fixing method.
4. Feed small end of cable tie (G) down through wall bracket (F) then put furniture back in place.
5. Feed small end of cable tie up through the furniture bracket (E), push into receiving end of the tie.
6. Now pull tight.
Now your furniture is now protected from falling over.
Please do not allow children to climb on the product.
IMPORTANT: Screws or wall fixing are not included with your product as wall construction varies
considerably so please select a suitable fixing method for the type of walls you have in your home.
If you are unsure about what type of fixing you require seek professional advice.
The anti-tilt device must not be modified or altered in any way.
To secure Furniture to the wall:
Safety Warning
Cable Tie
(G)
WALL
Fit two brackets
to the wall (F).
Bracket(s)
pre-fitted to
the furniture