Time4Sleep LANGHAM OTTOMAN User manual

LANGHAM OTTOMAN BED
DOUBLE AND KING SIZE
Parts Identification
Page 1 of 7
PLEASE READ
this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the pack supplied and check the contents against the
parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in
a safe environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be
diovaot,ylbmessagnirudnerdlihcgnuoymorfyawatpek
the danger of choking.
IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - PLEASE READ THESE INSTRUCTIONS CAREFULLY.
200815
1
2
3L
3R
4R
4L
5
6
6
7
7
8
9
10
12
12
11
11
13
13
14
15
15
16
17
17
19
18
19

6
9
10
2
1
1
Ref. Qty
Ref. Description
5
Qty
1
2
3L & 3R
1
1
1 Pr
Parts Checklist
Description
4L & 4R 1 Pr
Page 2 of 7
1
Headboard
Footboard
Side Rail - LH & RH
Lift Mechanism - LH & RH
‘U’ Shaped Bar
Frame Support Bracket
Gas Lift Piston
Cross Bar for Metal Slat Frame - Footend
Cross Bar for Metal Slat Frame - Headend
Fabric Handle
7
8
2
1
16
19
Wooden Slat Double/King
Angle Bracket
Single Plastic Cap
Double Plastic Cap
1
2
15
11
12
13
28/30
2
28/30
14 14/15
2
Mattress Stopper
Fabric Base Cover
Side Rail for Metal Slat Frame
Centre Rail for Metal Slat Frame
Centre Support Legs
17
18
2
1
Double/King
Double/King
Fittings Checklist
QtyCode Description
A x10
C
x8
D
Qty
Code Description
B
x12
x8 H
HARDWARE NEEDED FOR BED ASSEMBLY
x12
x2
x10
E
Bolts (M6x40mm) for fitting
Centre Support Bar Legs (19)
to Metal Slat Frame
x1
K
F
x2
G
Additional Tools Required
Care & Maintenance
Please retain your assembly instruction and
tools provided for future use.
Periodically check that all bolts are still tight.
General Hints & Tips
A ssembly requires two persons.
Approximate time to
assemble this product
In the unlikely event of missing or damaged parts,
please contact your retailer. Please have this guide at
hand quoting the part code reference numbers shown
when requesting spare or replacement parts.
J
x1
Flat Washers for M8 bolts
Bolts (M8x45mm) for fitting
Metal Slat Frame to Lift
Mechanism (4) and fitting
‘U’ Shaped Bar (5) to Side
Rails.
Bolts (M8x30mm) for fitting
Lift Mechanism (4) to Side
Rails
Bolts (M8x16mm) for fitting
Frame Support Brackets (6) and
Angle Brackets(12) to
Headboard and Footboard (1&2)
Bolts (M6x10mm) for
assembling Metal Slat Frame
Bolts (M8x25mm) for fitting
Side Rails(3) to Headboard
& Footboard (1&2)
Allen Key for M8 bolt
Spanner for M8 nut
Loc-nuts for M8 Metal Slat Frame
bolts and Gas Lift pistons

Stage
1
Stage
2
Page 3 of 7
Bed Assembly
C x4
J
x1
1
2
6
J
J
J
Cx2
B x8
J
x1
3L
3R
4L
4R
Bx4
Bx4

1
2
3L
3R
Stage
3
Stage
4
Page 4 of 7
Bed Assembly
Hx8
J
x1
C x8
J
x1
Make certain the bed is squared up
as shown in the diagram then tighten
all bed assembly bolts 100%.
100%
J
J
J
H
A
Cx4 A
A x4
5
12

Stage
5
Stage
6
Page 5 of 7
Bed Assembly
Dx12
J
x1
8
9
15
15
16
17
17
18
J
D
D
This is looking from underneath
the Metal Slat Frame.
Please ensure that the holes
for Gas Lift Mechanisms are
aligned as shown
Ensure that holes are aligned
on all corners of the Metal
Slat Frame (8), (9) & (17)
and Metal Centre Bar (18).

J
J
Ax3
Fx3
K
G
E
N
N
K
Stage
7
Stage
8
Page 6 of 7
Bed Assembly
N x4
Kx1
7
10
19
K x1
G x2
J
x1
x6
F
x6
A
x2
E
10

Stage
9
Page 7 of 7
Bed Assembly
13
13 11
11
11
11 14
18
17
Overall Dimension (L x W x H CM)
Double: 205.5 x 144 x 136/31
King : 215.5 x 159 x 136/31
Storage Dimension (L x W x H CM)
Double: 193 x 137.5 x 22.5
King : 203 x 152.5 x 22.5
D 144 K159
136
5.22
31
2
D 205.5 K 215.5
D 137.5 K 152.5
9.5
D 193 K 203
4.5
3