EAST COAST Dorset Wardrobe User guide

Dorset
Wardrobe
Assembly and care
instructions

Hardware
G x 10
B x 4
(6mm diameter)
E x 4
(medium)
J x 8
A x 16
(8mm diameter)
C x 4
D x 12
(short)
H x 10
F x 4
(long)
Hexagon Key x 1
I x 14
Thank you for purchasing an East Coast product. It’s been carefully designed and constructed to oer
quality, safety and reliability for you and your baby.
If you have a query about this product or require replacement parts, please contact 01692 408802.
Your child’s safety is your responsibility. Keep children clear during assembly as the fittings pack contains
small parts which may present a choking hazard. Please read the instructions and warnings carefully before
use.
Lay out the parts on a soft level surface and compare to the parts checklist. Don’t throw away any
packaging until you’re sure that you have all the parts.
You will need the following tools to complete assembly:
Flat-headed screwdriver and cross-point screwdriver
IMPORTANT
RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
K x 30
L x 6
M x 8
(4 x light, 4 x dark)
N x 1
2

Wooden Parts
Wardrobe side x 2 (L & R)
Back Panel x 2
Door x 2
Top panel
Plain crossbar x 3
Upper crossbar x 2
Clothes rail x 2
Shelf
Drawer back
Drawer base
Drawer front
Drawer side x 2 (L & R)
3

Assembly 1
Assembly 2
NOTE: Take care to insert the dowels
into the correct holes as indicated.
G x 5
Wardrobe side
NOTE: Repeat for the second
Wardrobe side.
A x 8
A x 8
Shelf
Upper crossbar
Plain crossbar
4

H x 5
1/2 turn
clockwise
H x 5
1/2 turn
clockwise
Assembly 4
Assembly 3
Upper crossbar
Shelf
Plain crossbar
Plain crossbar
Wardrobe side
Wardrobe side
NOTE: Ensure that the Upper crossbars are
fitted with part H inserted from above as
shown.
5

I x 3
I x 11
Assembly 5
Assembly 6
Top panel
6

NOTE:
This stage is best carried out with the wardrobe laid on its front
on a soft surface.
1. Place one Back panel into the recess on the back of the
wardrobe in the positions shown in the diagram (make
sure that the screw holes on the long edge are against
the frame of the wardrobe, and the holes across the
centre align with the Crossbar).
2. Slide the Joining strip (part N) onto the edge of the Back
panel and then slot the remaining Back panel into it.
3. Secure each Back panel in place with screws K.
K x 30
Assembly 7
Back Panel
Back Panel
N
7

Assembly 9
Assembly 8
Assembly 10
B x 2
B x 2
J x 4
M x 2
Drawer front
Drawer base
Clothes rail
Drawer back
Drawer front
8

Assembly 11
Assembly 12
Drawer side
Drawer side
Drawer back
E x 2
F x 2
C x 2
NOTE: Repeat for second drawer side
NOTE: To prepare the Drawer runners,
compare with images 1 and 2 below.
If part A is in position 1, move forward against the spring pressure until firm resistance is felt.
Press the tab on A down to lock in position.
Slide part B forward until it is at the front edge of the runner.
A
B
A
B
1
2
WRONG
CORRECT
Drawer runner
9

Assembly 13
Completed Drawer
NOTE: Position the drawer mounted strip
inside the inner runner and holding the drawer
level, gently slide the drawer all the way into
the frame.
To remove the drawer, locate the
plastic tabs on the drawer mounted
strips. Press gently down on one
side and lift the other whilst pulling
the drawer out.
10

Assembly 14
The wardrobe is supplied with a fixing kit which will secure it and help to guard against accidental
tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
1. Place the wardrobe against the wall where it is to be fitted. Mark the wall at the centre of the top edge
of the wardrobe. Move the wardrobe away.
2. Using the 25mm screw, washer and the appropriate wall fixing, attach the fabric strap to the marked
position.
3. Re-position the wardrobe. Attach the strap to the top of the wardrobe using the 15mm screw and the
washer.
4. Proceed to Assembly 15 to fit and adjust the doors.
Before use, ensure that the strap is securely fixed to both the wall and the wardrobe.
Washer x 2
Screw (short)
Screw (long)
Plastic wall plug
(for brick and masonry wall use
only)
Fabric strap
1
2
3
The type of wall fixing you will require depends on the construction of the wall. See below for details. If in
doubt, seek professional advice:
Wood: If fixing to wood
make sure that it isn’t
chipboard as screws can
easily pull away the core
structure.
Brick or masonry: Use the
wall plug, provided you are
sure that your wall is
sound.
Cavity wall: Special toggle
wall plugs needed.
Seek expert advice.
11

Assembly 15
Assembly 16
M x 1
D x 2
(6 total)
Door
NOTE:
Repeat for second door.
NOTE:
Attach hook 1. to the front edge of the hinge plate and clip the
rear of the hinge into position (2.).
To adjust the fit of the doors in the frame, position the wardrobe
where it will be used and use screws A and B:
Screw A moves the door closer to, or further from the frame
edge.
Screw B moves the door forward and back in the frame.
2.
J x 2
1.
A
B
12

8291-01
For customer care or enquiries:
Call: 01692 408802
Email: [e-mail]
East Coast Nursery Ltd. Robertson House, North Walsham,
Norfolk, NR28 0BX
eastcoastnursery.co.uk
Care and maintenance
In use
All assembly fittings should be tightened properly and should be checked regularly and re-tightened as
necessary. Take care when moving the furniture, as careless handling may cause damage.
Cleaning is simple; just wipe over with a damp cloth, and avoid using strong detergents or abrasives.
An occasional light application of a wax polish will help maintain the finish.
Be aware of the risks of open fires and other such sources of strong heat, such as electric bar fires, gas
fires, etc. in the near vicinity of the wardrobe.
Do not use if any of the parts are broken, torn or missing.
Any additional or replacement parts can only be obtained from the manufacturer or the distributor.
Only use the wardrobe on a stable and level surface.
Ensure that the wall strap is used to securely attach the wardrobe to the wall to prevent tipping.