Time4Sleep MAYA User manual

MAYA OTTOMAN BED
Parts Identification
Page 1 of 9
PLEASE READ
this sheet prior to assembly to familiarise yourself with
the various stages of construction. Carefully open the pack supplied and
check the contents against the parts and fittings check list.
Do not destroy any of the packaging until you are certain that you have
all the necessary parts for the assembl
y.
Please ensure that the packaging is disposed of in a safe environmentally
friendly way.
CAUTION: There are small components used in the construction of this
diovaot,ylbmessa
gnirudnerdlihcgnuoymorfyawatpek
the danger of choking.
IMPORTANT: BEFORE STARTING TO ASSEMBLE THE BED - PLEASE READ THESE INSTRUCTIONS CAREFULLY.
MK1 230408
2
15
15
15
15
16 17
3
4
6
6
5
12
14
14
12
13
11
11
7
10
8
8
1
unit. These loose items should be
DOUBLE AND KING SIZE
9
16
17
Before assembling the bed, please open
and locate the folowing parts:
the compartment at the rear of headboard
Both wings 16 and 17

62
Ref. Qty
Ref. Description
5
Qty
1
2
3
1
1
1
Parts Checklist
Description
4 1
1
Headboard
Footboard
Side Rail - LH
Side Rail - RH
Metal Lift Up Slat Frame
Metal Connection Plates
11 2
10
13
15
16
1
4
1
1
‘U’ Shape Cross Bar
14 2 Gas Lift Pistons
Mattress Stoppers
12
Fittings Checklist
Care & Maintenance General Hints & Tips
Please retain your assembly instruction and
tools provided for future use.
Periodically check that all bolts are still tight.
Approximate time to
assemble this product
In the unlikely event of missing or damaged parts,
please contact your retailer. Please have this guide at
hand quoting the part code reference numbers shown
when requesting spare or replacement parts.
Qty
Code Description
HARDWARE NEEDED FOR BED ASSEMBLY
x1
F
D
E
x1
Allen key for M8 bolts
Spanner for M8 nuts
x12
GFlat Washer for M8 Bolt
Nuts for M8 bolts
2
x10
Frame Support Brackets
7
13
3&4
1
Slat Frame Cross Bar
Feet
NOTE: Before moving the slat frame, place the mattress on the slats. Without a mattress in place, the
speed of movement is quick and may cause injury so great care is needed.
Carefully lower the frame with the fabric hand-strap (10) ensuring the frame sides are aligned with the side
panels; there should be an even gap on each side.
If not aligned, check bed is still square (see Stage 3) and if it is, but gaps are still not even, re-align.
Depending on the weight of the mattress, the rising speed will vary so be careful until you get used to the
speed.
Always use the hand-strap to lift or lower the frame - keep fingers well away from the moving parts.
When fully assembled and the mattress in position, please raise & lower the ottoman 4/5 times to
ensure the gas pistons are fully lubricated.
Page 2 of 9
Two person
assembly
Warnings
QtyCode Description
A
C
x8
B
x18
x24
LH Wing
17 1
RH Wing
8
9
2
1
Angled Corner Brackets
revoCesaBcirbaF
Fabric Strap Handle
Bolts (M8x16mm) for
fitting frame support brackets (11)
to headboard and footboard;
fitting angled corner bracket (8);
fitting metal connection plate (6)
and slat frame cross bar (7) to
metal slat frame (5)

MAYA
OTTOMAN
BED
Page 3 of 9
Warning
You must ensure that the mattress is on the bed frame before operating the lift mechanism
Failure to do so could result in injury.
Keep hands clear of the mechanism when opening or closing the ottoman.
Beware of entrapment – Never reach in through the mechanism to access the storage area.
Always ensure that the ottoman is FULLY opened before accessing the storage area.
Do not exceed the maximum weight as specified in the table below:
•
•
•
•
•
Use caution when operating, always use the handle when lifting.
Note: This bed uses a pressurised mechanism.
To be operated by adults only
Please ensure that children and pets are kept away from the bed when operating the
lift mechanism.
Keep children and pets away from the storage area.
Do not overload the internal storage base.
Do not stand inside the internal storage area of the bed.
Before removing the mattress secure the frame to ensure it does not open unexpectedly.
Do not attempt to lie on the mattress when the ottoman is in the raised position.
When lifting the ottoman remove all bedding except the fitted sheet.
•
•
•
•
•
•
•
•
•
•
Don’t lift without mattress Ensure mattress is on
before lifting
WARNING: ONLY USE THE HANDLE TO LIFT &
LOWER THE BED FRAME TO
AVOID TRAPPING FINGERS!
SAFETY WARNING
PLEASE DO NOT ALLOW CHILDREN
OR PETS INSIDE THE STORAGE AREA.
SAFETY WARNING
PLEASE BE CAREFUL WHEN LIFTING.
ONLY LIFT WITH MATTRESS ON TOP.
TO BE OPERATED BY ADULTS ONLY.
TO AVOID ACCIDENTS
TO ACCESS THE STORAGE AREA THE OTTOMAN FRAME
MUST BE FULLY OPENED AND THEN FULLY CLOSED AFTERWARDS
Bed Bed Size Min Weight (kg) Max Weight (kg)
Double 10 40
King 15 45

Stage
1
Stage
2
Page 4 of 9
Bed Assembly
C x4
E
x1
C x2
A x2
x4
1
2
3
4
B x8
E
x1
B
A x8

Stage
3
Stage
4
Page 5 of 9
Bed Assembly
C x8
E
x1A x4
100%
&
C x4
Ax2
8
3 4
&
3
4
13
Lift and turn bed on its side and with assistant holding
bed upright for safety, attach fabric base cover (9) to
bottom of side-rails, headboard & footboard with the
velcro tape. Make sure fabric is fixed evenly all round.
CAREFULLY LIFT BOTH HEADBOARD
& FOOTBOARD AT THE SAME TIME,
DO NOT LET THE BED TWIST
!
WARNING
9

6
5
7
7
C x2
C
Stage
5
Page 6 of 9
Bed Assembly
C x6
E
x1
12
12
ii)
iii)
Fitting position for the slat-frame cross
bar (7) is clearly labeled. At the end of
the slat frame (5), pass the bar through
the gap between second & third slat.
Carefully open the frame.
i)
The cross bar fixing
plates sit on top of each
side of the slat frame (5),
sit the plates on the round
labels. Align with the
threaded holes and loosely
fix through the plates using
two bolts (C).
Using Allen key (E), tighten
all six bolts 100%.
To top of the slat frame, fit two
connection plates (6) using four
bolts (C). Screw the bolts into
the threaded inserts on top of
the frame.
Please do not tighten 100% yet.

D
14
Page 7 of 9
Bed Assembly
Stage
7
Stage
6
Dx2
F x1
SMALL GAP
Slide gas-lift piston stem
(x) onto the axle (y) then
fit the flange lock-nut (D).
Tighten nut with spanner
(F) - do not over-tighten
A small gap must be left
so stem can move freely -
this is normal , see sketch
below.
y
x
D
x1 F
Ex1
A x6 x6
10
G x6
Ax3
Dx3
Bolt into centre of long holes
Loosely fit three bolt sets on each side (A), (D) & (G),
carefully hold frame down and align so there even
gaps at each side then tighten all bolts 100%
Gx3

x1
Ex6 G
A x6
Dx2 F x1
Page 8 of 9
Stage
8
Stage
9
Bed Assembly
Note: Be careful what you store
under the bed - the top of an item,
like a suitcase or a box, must not
touch the slats or they may be
damaged. Maximum storage height
is 25cm.
D
D
F
SMALL GAP
14
Slide gas-lift piston stem (x)
onto the axle (y) then fit the
flange lock-nut (D).
Tighten nut with spanner (F)
- do not over-tighten.
A small gap must be left so
stem can move freely - this
is normal, see sketch above.
x
y
Note: Open the back fabric cover of the headboard,then to fix the both wings

Page 9 of 9
Overall Dimensions (LWH cm)
Double: 206 x 144 x 135
King: 216 x 159 x 135
Storage Dimensions (LWH cm)
Double: 193 x 137.5 x 25
King: 203 x 152.5 x 25
19
32
5
3
3
Slat width
5.3
W
H
L
3
29
Floor to top
of slat
Top of side rail
to top of slat
Distance between slats (cm)
Ottoman Piston Strength (N)
7.3
800
Technical Specifications
Stage
10
Note: Close the back fabric cover of the headboard.