Titan Fitness SHPULTWRv3 User manual

SHORT WALL MOUNTED PULLEY TOWER
SHPULTWRv3
400811
Operator’s Manual
Read the Operator’s Manual entirely. When you see this
symbol, the subsequent instructions and warnings are
serious follow without exception. Your life and the lives
of others depend on it!

2
PARTS DIAGRAM / EXPLODED VIEW

3
PARTS LIST
HARDWARE LIST

4

5
ASSEMBLY INSTRUCTIONS
STEP 1
1. Push the END COVER (V) onto the end of FRONT BEAM (A) and the end of REAR
BEAM (B).
2. Assemble the BASE FRAME (C), FRONT BEAM (A), REAR BEAM (B) and LOWER
MOUNTING FRAME (G) using BOLT M10x70 (4), WASHER M10 (7) and NYLON
NUT M10 (8).

6
ASSEMBLY INSTRUCTIONS
STEP 2
1. Attach the GUIDE TUBE (D) to the REAR BEAM (B) using BOLT M10x20 (1) and
WASHER M10 (7).
2. Screw the RUBBER BUMPER (U) ON the GUIDE TUBE (D), Slide the WEIGHT
CARRIAGE (J) on the GUIDE TUBE (D).
3. Slide the RUBBER CUSHION(L) and SPRING CLIP (Q) onto the rod of WEIGHT
CARRIAGE (J).

7
ASSEMBLY INSTRUCTIONS
STEP 3
1. Attach the FRONT UPRIGHT (E) to the BASE FRAME (C) using BOLT M10x50 (3),
WASHER M10 (7) and NYLON NUT M10 (8).
2. Slide the MULTI-PULLEY BRACKET (F) onto FRONT UPRIGHT (E), screw the KNOB
(P) into the MULTI-PULLEY BRACKET(F).

8
ASSEMBLY INSTRUCTIONS
STEP 4
1. Assemble the UPPER FIXING FRAME (H) to the FRONT UPRIGHT (E) using BOLT
M10x50 (3), WASHER M10 (7) and NYLON NUT M10 (8).
2. Assemble the UPPER FIXING FRAME (H) to the GUIDE TUBE (D) using BOLT
M10x20 (1) and WASHER M10 (7).
3. Assemble the UPPER MOUNTING FRAME (I) to the UPPER FIXING FRAME (H)
using BOLT M10x70 (4), WASHER M10 (7) and NYLON NUT M10 (8).

9
ASSEMBLY INSTRUCTIONS
STEP 5
1. Assemble two pcs PULLEY (M3/M7) to the MOVABLE PULLEY BRACKET (K) using
BOLT M10x75 (5), WASHER M10 (7) and NYLON NUT M10 (8).
2. Assemble the other 11 pcs PULLEY (M1~M13, EXCEPT M3 & M7) to its own
BRACKET (K) using BOLT M10x45 (2),WASHER M10 (7) and NYLON NUT M10 (8).
ASSEMBLY POSITION IS SHOWN IN THE FIGURE ABOVE.

10
ASSEMBLY INSTRUCTIONS
STEP 6
1. Fix the CABLE (S) to the MULTI-PULLEY BRACKET (F) using SAFETY HOOK (N),
insert it through the below of PULLEY (M12), through the above of PULLEY (M13),
then fix the other end of CABLE (S) to the BASE FRAME (C) using the SAFETY HOOK
(N) and the CHAIN (O).

11
ASSEMBLY INSTRUCTIONS
STEP 7
1. Install the CABLE (LONG) (R) in the following route: Pass through the
PULLEY(M1&M10), above M2, below M3, above M4, below M5 (from the same
side), above M6, below M7, above M8, finally pass through M9 & M11.
2. Attach the DRAWSTRING (T) to the end of CABLE (LONG)(R) using the SAFETY
HOOK (N).
ATTENTION: PLEASE MAKE SURE ALL THE CABLES BE PUT IN THE GROOVE OF
PULLEY AND TIGHTEN ALL NUT-AND-BOLT COMBINATIONS BEFORE USE.

12
ACKNOWLEDGEMENT OF RISK AND RELEASE OF LIABILITY
The use of any equipment, including this one, involves the potential risk of injury. Apart from any warranty
claim that might be presented for a claimed defect in material or workmanship of the product, you accept
and assume full responsibility for any and all injuries, damages (both economic and non-economic), and
losses of any type, which may occur, and you fully and forever release and discharge Titan, its insurers,
employees, officers, directors, associates, and agents from any and all claims, demands, damages,
rights of action, or causes of action, present or future, whether the same be known or unknown,
anticipated, or unanticipated, resulting from or arising out of the use of said equipment.
This equipment must be used with care by capable and competent individuals under supervision,
WARNING
Heavy object. Use lifting aids and
proper lifting techniques when moving.
Choking hazard. Small parts –
Please exercise caution if small
children or pets are present.
Sharp objects may be involved.
Use precaution and protection.
TITAN LIMITED WARRANTY: TERMS, EXCLUSIONS AND LIMITATIONS OF REMEDIES
This product comes with a one (1) year limited warranty that can be found at
www.titan.fitness/warranty.html Please review the same for all details regarding the
Titan Limited Warranty.
THE TITAN LIMITED WARRANTY FOUND AT WWW.TITAN.FITNESS/WARRANTY IS EXCLUSIVE AND IS IN
LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE, EACH OF WHICH IS HEREBY
DISCLAIMED.

13
NEED HELP? CONTACT US FIRST.
1-888-410-1503
info@titan.fitness
www.titan.fitness
© 2021 Titan Brands