Titan TTB689CSW Installation manual
MINI CIRCULAR SAW 500W TTB689CSW
SAFETY AND OPERATING MANUAL
Original Instructions V5.0
25
20
15
10
5
0
MINI CIRCULAR SAW 500W TTB689CSW
1
Congratulations on your purchase of a power tool from Titan Power Tools
(UK) Ltd. We want you to continue getting the best performance from it so this hand-
book includes information on safety, handling and care. Please retain this handbook
in case of you need to refer to any of the information in the future.
Your power tool comes with a 2 year guarantee, so should it develop a fault
within this period contact your retailer.
GUARANTEE
This product carries a guarantee of 2 years. If your product develops a fault
was purchased.
- Fair wear and tear
- Misuse or abuse
- Lack of routine maintenance
- Failure of consumable items (such as batteries)
- Accidental damage
- Cosmetic damage
- Failure to follow manufacturer’s guidelines
- Loss of use of the goods
This guarantee does not affect your statutory rights. This guarantee is only valid in
the UK.
For any enquiries relating to the guarantee please refer to your retailer.
MINI CIRCULAR SAW 500W TTB689CSW
2
GENERAL SAFETY INSTRUCTIONS
WARNING Read all safety warnings and all instructions. Failure to follow the
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
1. Work area safety
a) Keep work area clean and well lit
b)
Power tools create sparks which may ignite the
c) Keep children and bystanders away while operating a power tool. Distractions
2. Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radia-
tors, ranges and refrigerators. There is an increased risk of electric shock if your
c) Water entering a power tool
will increase the risk of electric shoc
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
e) -
door use.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RC D) protected supply.
3. Personal safety
a) Stay alert, watch what you are doing and use common sense when operating
of drugs, alcohol or medication. A moment of inattention while operating power tools
b) Use personal protective equipment. Always wear eye protection.
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
MINI CIRCULAR SAW 500W TTB689CSW
3
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in personal
e) Do not overreach. Keep proper footing and balance at all times. This enables
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, cloth-
ing and gloves away from moving parts.
g)
facilities, ensure these are connected and properly used. Use of dust collection
4. Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
-
b) Do not use the power tool if the switch does not turn it on and off. Any power
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s opera-
tion. If damaged, have the power tool repaired before use. Many accidents are
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be per-
formed. Use of the power tool for operations different from those intended could result
5. Service
a)
replacement parts.
MINI CIRCULAR SAW 500W TTB689CSW
4
MACHINE SPECIFIC SAFETY WARNINGS FOR ALL SAWS
Cutting procedures
a)
If both hands are holding the saw,
b) Do not reach underneath the workpiece. The guard cannot protect you from the blade
c) Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of
d) Never hold piece being cut in your hands or across your leg. Secure the work-
piece to a stable platform. It is important to support the work properly to minimize body
e) Hold the power tool by insulated gripping surfaces only, when performing an
operation where the cutting tool may contact hidden wiring or its own cord.
f) When ripping, always use a rip fence or straight edge guide.-
g) Always use blades with correct size and shape (diamond versus round) of arbour
holes. Blades that do not match the mounting hardware of the saw will run eccentrically,
h) Never use damaged or incorrect blade washers or bolt. The blade washers and bolt
Kickback and related warnings
-
ging causes rapid stalling of the rotating wheel which in turn causes the uncontrolled power
wheel that is entering into the pinch point can dig into the surface of the material causing
-
-
control over kickback or torque reaction during start-up. The operator can control
MINI CIRCULAR SAW 500W TTB689CSW
5
b) Never place your hand near the rotating accessory.
c)Do not position your body in line with the rotating wheel. Kickback will propel the
d) Use special care when working corners, sharp edges etc. Avoid bouncing and
snagging the accessory.
e)Do not attach a saw chain, woodcarving blade, segmented diamond wheel with a
peripheral gap greater than 10 mm or toothed saw blade. Such blades create frequent
to twisting or binding of the wheel in the cut and the possibility of kickback or wheel break-
g) When wheel is binding or when interrupting a cut for any reason, switch off the
power tool and hold the power tool motionless until the wheel comes to a complete
stop. Never attempt to remove the wheel from the cut while the wheel is in motion
otherwise kickback may occur.
h) Do not restart the cutting operation in the workpiece. Let the wheel reach full
speed and carefully re-enter the cut. The wheel may bind, walk up or kickback if the
i) Support panels or any oversized workpiece to minimize the risk of wheel pinching
and kickback.
placed under the workpiece near the line of cut and near the edge of the workpiece on both
areas.
Guard function
a) Check guard for proper closing before each use. Do not operate the saw if guard
does not move freely and enclose the blade instantly. Never clamp or tie the
If saw is accidentally dropped, guard may be
b) Check the operation and condition of the guard return spring. If the guard and
the spring are not operating properly, they must be serviced before use. Guard
c) Assure that the base plate of the saw will not shift while performing the “plunge
cut” when the blade bevel setting is not at 90°. Blade shifting sideways will cause
d) Always observe that the guard is covering the blade before placing saw down on
MINI CIRCULAR SAW 500W TTB689CSW
6
An unprotected, coasting blade will cause the saw to walk backwards,
Safety instructions for abrasive cutting-off operations
Cut-off machine safety warnings
a) The guard provided with the tool must be securely attached to the power tool and
the operator. Position yourself and bystanders away from the plane of the rotating
wheel. The guard helps to protect operator from broken wheel fragments and accidental
b) Use only bonded reinforced or diamond cut-off wheels for your power tool. Just
because an accessory can be attached to your power tool, it does not assure safe opera-
marked on the power tool. Accessories running faster than their rated speed can break
grind with the side of cut-off wheel.
selected wheel.
f) Do not use worn down reinforced wheels from larger power tools. Wheels intended
g) The outside diameter and the thickness of your accessory must be within the
capacity rating of your power tool. Incorrectly sized accessories cannot be adequately
tool.
i) Do not use damaged wheels. Before each use, inspect the wheels for chips and
cracks. If power tool or wheel is dropped, inspect for damage or install an undam-
aged wheel. After inspecting and installing the wheel, position yourself and bystand-
no load speed for one minute. Damaged wheels will normally break apart during this test
j) Wear personal protective equipment. Depending on application, use face shield,
safety goggles or safety glasses. As appropriate, wear dust mask, hearing protec-
tors, gloves and shop apron capable of stopping small abrasive or workpiece frag-
ments.
MINI CIRCULAR SAW 500W TTB689CSW
7
k) Keep bystanders a safe distance away from work area. Anyone entering the work
area must wear personal protective equipment. Fragments of workpiece or of a broken
I) Hold the power tool by insulated gripping surfaces only, when performing an
operation where the cutting accessory may contact hidden wiring or its own cord.
m) Position the cord clear of the spinning accessory. If you lose control, the cord may
n) Never lay the power tool down until the accessory has come to a complete stop.
o) Do not run the power tool while carrying it at your side. Accidental contact with the
p) Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside
Sparks could ignite these
r) Do not use accessories that require liquid coolants. Using water or other liquid cool-
GENERAL SAFETY WARNINGS FOR LASER
CAUTION: LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
Max. Power: < 1mW Wave Length: 650nm
EN 60825-1: 2007
a)
b) The laser shall be used and maintained in accordance with the manufacturer’s instruc-
c)
d)-
e)-
f)
g)
MINI CIRCULAR SAW 500W TTB689CSW
8
GENERAL SAFETY WARNINGS FOR BATTERIES
a) CAUTION!
b)
c)-
d)
e)
f)
ADDITIONAL SAFETY WARNING FOR CONSTRUCTION DUST
Silica is a natural mineral present in large amounts in things like sand, sandstone and
Lung cancer
Silicosis
The risk of lung disease is linked to people who regularly breathe construction dust
penny it is tiny – like a small pinch of salt:
MINI CIRCULAR SAW 500W TTB689CSW
9
WARNING!
Some dust created by power sanding, sawing, grinding, drilling, and other construction
examples of these chemicals are:
- Lead from lead-based paints,
-
-
-
-
MINI CIRCULAR SAW 500W TTB689CSW
10
NOISE INFORMATION
Wear hearing protection!
VIBRATION
to make informed decisions as to the period of time a power tool can be used safely on a
cutting wood
cutting metal
cutting ceramic
h
-
WARNING!
-
MINI CIRCULAR SAW 500W TTB689CSW
11
WARNING!
Identify safety measures to protect the operator that are based on an estimation of expo-
sure in the actual conditions of use (taking account of all parts of the operating cycle such
as the times when the tool is switched off and when it is running idle in addition to the trig-
Vibration and noise reduction
Maintain this product in accordance with these instructions and keep it well lubricated
Emergency
Familiarise yourself with the use of this product by means of this instruction
manual. Memorise the safety directions and follow them to the letter. This will help
to prevent risks and hazards.
Residual risks
MINI CIRCULAR SAW 500W TTB689CSW
12
with the structure and design of this product:
WARNING!
Health Surveillance
Double insulation
Important note
MINI CIRCULAR SAW 500W TTB689CSW
13
SYMBOLS
product.
Wear ear protection
Wear eye protection
Wear respiratory protection
Warning
Laser radiation
Do not stare into beam
Waste electrical products should not be disposed of with
MINI CIRCULAR SAW 500W TTB689CSW
14
3
25
20
15
10
5
0
Ø85mm x Ø10mm x 1.6mm x 80T
max 7000/min
Titan Power Tools (UK) Ltd. BA22 8RT
Titan Power Tools (UK) Ltd. BA22 8RT
Ø85mm x Ø10mm x 1.6mm x 20T
max 7000/min
Titan Power Tools (UK) Ltd. BA22 8RT
HW
HS
Ø85 x 1.8 x 5 x Ø10mm
max 18000/min 80m/s
MINI CIRCULAR SAW 500W TTB689CSW
15
1. Reset button
2. Main handle
3. Safety lock switch
4. On / Off switch
5. Depth clamping knob
6. Cutting depth scale
7.
8.
9. Cutting depth guide rail
10. Saw blade safety guard
11. TCT blade
12. Laser
13. Laser battery compartment
14. Laser On / Off switch
15. Base plate
16. Spindle lock button
17. Parallel guide clamping knob
18.
19. HSS blade
20. Diamond blade
21. Parallel guide
22.
23. Dust adaptor
MINI CIRCULAR SAW 500W TTB689CSW
16
Model TTB689CSW
Rated voltage 230-240V~ 50Hz
Rated power 500W
No load speed 7000min-1
Blade size Ø 85mm
Bore size 10mm
Weight 1.98kg
Laser class Class 2
Wavelength 650nm
NOISE DATA
pA = 90 dB(A) K=3dB(A)
wA =101 dB(A) K=3dB(A)
Wear ear protection when sound pressure is over 80dB(A)
ACCESSOIRES
- 1pc Parallel guide
- 1pc Dust adaptor
TECHNICAL DATA
LASER INFORMATION
MINI CIRCULAR SAW 500W TTB689CSW
17
OPERATING INSTRUCTIONS
-
tion manual carefully.
Intended use
The tool is designed for longitudinal cutting of solid
wood, wood-like materials and plastics when equipped
with appropriate saw blades, or - when connected to a
suitable dust extraction system - for dry cutting of min-
1. On/Off switch (Fig.1-2)
Press the safety lock switch and slowly push the tool
Caution!
Always carry out a test run before starting work and af-
Fig.1
Fig.2
0
0
0
MINI CIRCULAR SAW 500W TTB689CSW
18
in good condition, correctly mounted and able to turn
2. Using the Parallel Guide Fence (Fig.3-4)
The parallel guide can be used for making cuts parallet
To set the cutting width, slide the guide arm through
If the distance between the side of the work
piece and the cutting position is too wide, or the side
3. Changing blade (Fig.5,6,7)
The direction-of-rotation arrow on blade and machine
(see direction-of-rotation arrow on the machine enclo-
To change the blade, switch off and unplug form power
Press the spindle-lock button in deep and hold it in this
the blade bolt, turn the spindle slightly with the free
washer and screw in position and then tighten blade
CAUTION!
The maximum rotation speed of blade must be greater
cutting results ensure you use a saw blade suited to the
Fig.3
Fig.4
Fig.5
Fig.6
MINI CIRCULAR SAW 500W TTB689CSW
19
4. Adjusting the cutting depth (Fig.8)
For optimal quality of cutting, the saw blade should not
below steps:
the required depth - as shown on the cutting depth
CAUTION!
5. LASER GUIDE (Fig.9)
depth of cut as required and rest the front edge of the
-
6. Install the battery of laser (Fig.10-11)
-
Fig.7
Fig.8
Fig.9
Fig.10
0
0
0
0
0
0
Other manuals for TTB689CSW
1
Table of contents
Other Titan Saw manuals
Titan
Titan ttb554tas User manual
Titan
Titan TTB867JSW User manual
Titan
Titan SF2841 Installation manual
Titan
Titan TTI880RSP User manual
Titan
Titan TTB236MSW Installation manual
Titan
Titan SF10N1 Installation manual
Titan
Titan TTB881RSP User manual
Titan
Titan TTB689CSW Installation manual
Titan
Titan TTB703SSW User manual
Titan
Titan TTB763TAS User manual
Titan
Titan TTB911CSW User manual
Titan
Titan TTB674TAS User manual
Titan
Titan TTB599BNS User manual
Titan
Titan TTB364BDS Installation manual
Titan
Titan SF210JSL Installation manual
Titan
Titan SF2541 Installation manual
Titan
Titan SF185R2 Installation manual
Titan
Titan SF16G User manual
Titan
Titan TTB287CSW Installation manual
Titan
Titan SF08N5 Installation manual
Popular Saw manuals by other brands
Ryobi
Ryobi ECS1285 Owner's operating manual
Tradesman
Tradesman BTS10BW owner's manual
Reliable Equipment
Reliable Equipment REL-CS16 Operator's guide
Skil
Skil 5385 operating instructions
Bosch
Bosch GSA 18 V-LI Professional Original instructions
MK Diamond Products
MK Diamond Products MK-1080 Operations & parts manual
