Titan TTB881RSP User manual

Original Instructions_MNL_TTB881RSP_(EN)_V01_211223
TTB881RSP
WARNING! Read the instructions before using the product!
EAN: 5059340252209

2
EN TTB881RSP
Let's
get started...
These instructions are for your safety. Please read through them thoroughly
before use and retain them for future reference.
Getting started... 02
Safety 03
Symbols 14
Your product 15
Technical and legal information 16
Before you start 18
In more detail... 23
Product functions 24
Operation 26
Care and maintenance 29
Trouble shooting 33
Guarantee 34
Declarations of conformity 35

33
Getting started...
EN
TTB881RSP
Safety warnings
General power tool safety warnings
WARNING! Read all safety warnings,
instructions, illustrations and specications
provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, re and/or serious injury.
Save all warnings and instructions for
future reference. The term “power tool” in
the warnings refers to your mains-operated
(corded) power tool or battery operated
(cordless) power tool.”
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
Safety

44
Getting started...
EN TTB881RSP
Electrical safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.
Safety

55
Getting started...
EN
TTB881RSP
Personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
2. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non- skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
3. Prevent unintentional starting. Ensure the
switch is in the off- position before connecting
to power source and/or battery pack, picking up
or carrying the tool. Carrying power tools with your
finger on the switch or energising power tools that
have the switch on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing away from
moving parts. Loose clothes, jewellery or longhair
can be caught in moving parts.
Safety

66
Getting started...
EN TTB881RSP
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
8. Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
Power tool use and care
1. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate
for which it was designed.
2. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
3. Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
4. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are dangerous
in the hands of untrained users.
Safety

77
Getting started...
EN
TTB881RSP
5. Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tools operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
8. Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
Service
1. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Safety

88
Getting started...
EN TTB881RSP
Additional safety warnings for reciprocating saw
1. Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden wiring
or its own cord. Cutting accessory contacting a
“live” wire may make exposed metal parts of the
power tool “live” and could give the operator an
electric shock.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the workpiece by hand or against your body
leaves it unstable and may lead to less of control.
3. Keep hands away from the sawing range. Do not
reach under the workpiece. Contact with the saw
blade can lead to injuries.
4. Apply the machine to the workpiece only when
switched on. Otherwise there could be danger of
kickback if the cutting tool jams in the workpiece.
5. When sawing, the guide plate must always be in
contact with the workpiece. The saw blade can
become wedged and lead to loss of control over the
machine.
6. When the cut is completed, switch off the machine
and then pull the saw blade out of the cut only after
it has come to a standstill. In this manner you can
avoid kickback and can place down the machine
safely .
Safety

99
Getting started...
EN
TTB881RSP
7. Use only undamaged saw blades that are in perfect
condition. Bent or dull saw blades can break,
negatively influence the cut, or lead to kickback.
8. Do not brake the saw blade to a stop by applying
side pressure after switching off. The saw blade can
be damaged, break or cause kickback.
9. Do not support the workpiece with your hand or
foot. Do not touch objects or the floor with the saw
running. Danger of kickback.
10.Use suitable detectors to determine if utility lines
are hidden in the work area or call the local utility
company for assistance. Contact with electric lines
can lead to fire and electric shock. Damaging a gas
line can lead to explosion. Penetrating a water line
cause property damage or may cause an electric
shock.
11.When working with the machine, always hold it
firmly with both hands and provide a secure stance.
The power tool is guided more securely with both
hands.
The following information applies to professional users
only but is good practice for all users:
Safety

1010
Getting started...
EN TTB881RSP
Additional safety warning for construction dust
The updated Control of Substances Hazardous to
Health Regulations 1st October 2012 now also targets
to reduce the risks associated with silica, wood and
gypsumdusts. Construction workers are one of the at-
risk groups within this because of the dust that they
breathe: silica dust is not just a nuisance; it is a real
risk to your lungs!
Silica is a natural mineral present in large amounts
in things like sand, sandstone and granite. It is also
commonly found in many construction materials such
as concrete and mortar. The silica is broken into very
ne dust (also known as Respirable Crystalline Silica
or RCS) during many common tasks such as cutting,
drilling and grinding. Breathing in very ne particles
of crystalline silica can lead to the development of:
Lung cancer Silicosis Chronic Obstructive Pulmonary
Disorder/Chronic Obstructive Pulmonary Disease
(COPD) and breathing in ne particles of wood dust
can lead to the development of Asthma. The risk of
lung disease is linked to people who regularly breathe
construction dust over a period of time, not on the odd
occasion.
To protect the lung, the COSHH Regulations sets a
limit on the amount of these dusts that you can breathe
(called a Workplace Exposure Limit or WEL) when
averaged over a normal working day. These limits are
not a large amount of dust: when compared to a penny
it is tiny – like a small pinch of salt: This limit is the legal
maximum; the most you can breathe after the right
controls have been used.
Safety

1111
Getting started...
EN
TTB881RSP
How to reduce the amount of dust?
1. Reduce the amount of cutting by using the best
sizes of building products. Use a less powerful e.g.
a block cutter instead of angle grinder.
2. Using a different method of work altogether – e.g.
using a nail gun to direct fasten cable trays instead
of drilling holes first.
3. Please always work with approved safety
equipment, such as those dust masks that specially
designed to filter out microscopic particles and use
the dust extraction facility at all time.
For more information please see the HSE website:
http://www.hse.gov.uk/construction or http://www.hse.
gov.uk/pubns/cis69.pdf
Safety

1212
Getting started...
EN TTB881RSP
WARNING! Some dust created by power
sanding, sawing, grinding, drilling and other
construction activities contains chemicals
known to cause cancer, birth defects or other
reproductive harm. Some examples of these
chemicals are:
• Lead from lead-based paint
• Crystalline silica from bricks and cement and
other masonry products
• Arsenic and chromium from chemically-
treated timber
Your risk from these exposures varies,
depending upon how often you do this type
of work. To reduce your exposure to these
chemicals:
• Work in a well-ventilated area.
• Work with approved protective equipment,
such as those dust masks that are specially
designed to lter microscopic particles.
Vibration
The European Physical Agents (Vibration) Directive
has been brought in to help reduce hand arm vibration
syndrome injuries to power tool users. The directive
requires power tool manufacturers and suppliers to
provide indicative vibration test results to enable users
to make informed decisions as to the period of time a
power tool can be used safely on a daily basis and the
choice of tool.
See technical specications in the instruction manual
for the vibration levels of your tool.
Safety

1313
Getting started...
EN
TTB881RSP
The declared vibration emission value should be used
as a minimum level and should be use with the current
guidance on vibration.
Calculating the actual period of use can be difcult and
the HSE website has further information.
While working with this power tool, hand/arm vibrations
occur. Adopt the correct working practices in order
to reduce the exposure to vibration. This tool may
cause hand-arm vibration syndrome if its use is not
adequately managed.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades. Maintain
this tool in accordance with these instructions and keep
well lubricated (where appropriate).
Avoid using tools in temperatures of 10ºC or less. Plan
your work schedule to spread any high vibration tool
use across a number of days.
NOTE: The use of other tools will reduce the users’ total
working period on this tool.
Health surveillance
All employees should be part of an employer’s health
surveillance scheme to help identify any vibration
related diseases at an early stage, prevent disease
progression and help employees stay in work.
Safety

1414
Getting started...
EN TTB881RSP
Residual risks
Even if you are operating this product in
accordance with all the safety requirements,
potential risks of injury and damage remain. The
following dangers can arise in connection with the
structure and design of this product:
1. Injuries and damage to property due to broken
attachments or the sudden impact of hidden objects
during use.
2. Danger of injury and property damage caused by
flying objects or poor power tool accessories.
Safety

1515
Getting started...
EN
TTB881RSP
On the product, the rating label and within these instructions you
will nd among others the following symbols and abbreviations.
Familiarise yourself with them to reduce hazards like personal
injuries and damage to property.
Read the instruction manual
Wear eye protection
Wear hearing protection.
Wear a dust mask.
Wear protective gloves
For wood cutting
For metal cutting
yyWxx
Manufacturing date code: Year of
manufacturing (20yy) and week of
manufacturing (Wxx)
The product complies with the applicable
European directives and an evaluation
method of conformity for these directives
was done.
UK Conformity Assessed
Symbols
Symbols

1616
Getting started...
EN TTB881RSP
Your product
Your product
1. Guide plate
2. Tool-less blade clamp
sleeve
3. Gripping surface
4. Lock-on button
5. On/off switch
6. Main handle
7. Hex key
8. Guide plate release screws
9. Blades x 2 (1 x metal blade,
1 x wood blade)
4
2
35
6
7
9
8
1

1717
Getting started...
EN
TTB881RSP
Technical specications
Reciprocating saw
Rated voltage, frequency: 220 -240 V~, 50 Hz
Rated power input: 850 W
Rated no load speed n0:0 - 3000 /min
Stroke length: 25 mm
Cutting Capacity:
in wood:
in metal:
in aluminum:
100mm
12mm
20mm
Weight: 2.17 kg
NOISE DATA
A weighted sound pressure: LpA=95.0 dB(A)
A weighted sound power: LwA=106.0 dB(A)
Uncertainty: KPA & KWA=3 dB(A)
The noise for the operator may exceed 80 dB(A) and ear
protection measures are necessary.
VIBRATION DATA
Cutting boards with the supplied
saw blade:
ah,B=25.68 m/s²
Cutting wooden beams with the
supplied saw blade:
a h,WB=32.54 m/s²
Uncertainty: K=1.5 m/s²
The declared vibration total values and the declared noise
emission values have been measured in accordance with a
standard test method (EN62841-1/EN62841-2-11) and may be
used for comparing one tool with another; they may also be used
in a preliminary assessment of exposure.
Technical and legal
information

1818
Getting started...
EN TTB881RSP
WARNING! The vibration and noise emissions
during actual use of the power tool can differ
from the declared values depending on the
ways in which the tool is used especially what
kind of workpiece is processed; and need to
identify safety measures to protect the operator
that are based on an estimation of exposure
in the actual conditions of use (taking account
of all parts of the operating cycle such as the
times when the tool is switched off and when it
is running idle in addition to the trigger time).
RATING LABEL EXPLANATION
TTB881RSP = MODEL NUMBER
TT= TITAN
B= 240V AC
881= Version Number
RSP = RECIPROCATING SAW
Technical and legal
information

1919
Getting started...
EN
TTB881RSP
Unpack
Unpack all parts and lay them on a flat, stable surface.
Remove all packing materials and shipping devices if
applicable.
Make sure the delivery contents are complete and free
of any damage. If you find that parts are missing or show
damage do not use the product but contact your dealer.
Using an incomplete or damaged product represents a
hazard to people and property.
Ensure that you have all the accessories and tools needed
for assembly and operation. This also includes suitable
personal protective equipment.
WARNING! The product and the packaging are
not children’s toys! Children must not play with
plastic bags, sheets and small parts! There is a
danger of choking and suffocation!
You will need
(items not supplied)
Suitable personal protective equipment
(items supplied)
Saw blade (for wood x1)
Saw blade (for metal x1)
Before you start

2020
Getting started...
EN TTB881RSP
Saw blades
Different saw blades can be used with this product depending on
the workpiece material.
WARNING! Always use saw blades according to the
intended use! For example, never use a saw blade
intended for working on wood for working on metal or
vice versa!
Observe the technical requirements of this product (see
section Technical specications) when purchasing and
using saw blades!
Some saw blades are very sharp and become hot dur-
ing use! Handle them carefully! Wear protective gloves
when handling saw blades in order to avoid injuries like
burns and cuts!
To install the saw blade
Use one hand to rotate the tool-less blade clamp sleeve (2) in the
direction of the arrow marked on the blade clamp and then hold it
in place. (Fig.1)
Use the other hand to insert the saw blade (9) into the blade clamp
(2) as far as possible.
Release the tool-less blade clamp sleeve (2), and the blade (9)
should be locked in place automatically. (Fig.2)
Try to push in and pull out blade (9) to check whether it is locked
correctly.
NOTE: The blade may be installed with the teeth
pointing up or down, according to the needs of the
cutting operation.
Before you start