Titan TTB911CSW User manual

Original Instructions –MNL_TTB911CSW_GB_V1_220119
TTB911CSW
1500W Circular Saw
EAN: 5059340349978
WARNING: Read the instructions before using the product!

EN
02
40
41
42
39
36
32
29
In more detail...
Product functions
Operation
Care and maintenance
Troubleshooting
Recycling and disposal
Guarantee
Declarations of conformity
28
02
03
20
23
Getting started...
Safety information
Your product
Before you start
These instructions are for your safety. Please read through them
thoroughly before use and retain them for future reference.
Let’s
get started...

Getting started...
EN
03
Safety information
Safety warnings
General power tool safety warnings
WARNING! Read all safety warnings, instructions,
power tool. Failure to follow all instructions listed
serious injury. Save all warnings and instructions
for future reference. The term “power tool” in the
warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power
tool!
Work area safety
>Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
>Donotoperatepowertoolsinexplosiveatmospheres,
or dust. Power tools create sparks which may ignite the
dust or fumes.
>Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
Electrical safety
>Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools.
matching outlets will reduce risk of electric shock.
>Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
>Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
TTB911CSW by TITAN

04
Safety information
Getting started...
EN
Safety warnings
>Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
>When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
>If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Personal safety
>Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
A moment
of inattention while operating power tools may result in
serious personal injury.
>Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
>Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool.
switch or energising power tools that have the switch on
invites accidents.
TTB911CSW by TITAN

Getting started...
EN
05
Safety information
>Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
>Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
>Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from
moving parts. Loose clothes, jewellery or long hair can
be caught in moving parts.
>If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
>Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
Power tool use and care
>Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
>Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
>Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from the
power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power
tool accidentally.
TTB911CSW by TITAN

06
Safety information
Getting started...
EN
Safety warnings
>Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
>Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
>Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
>Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Service
>person using only identical replacement parts. This
will ensure that safety of the power tool is maintained.
Circular saw safety warnings
Safety instructions for all saws - Cutting procedures
>DANGER: Keep hands away from cutting area and
the blade. Keep your second hand on auxiliary
handle, or motor housing. If both hands are holding
the saw, they cannot be cut by the blade.
>Keep handles and grasping surfaces dry, clean
and free from oil and grease.Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
TTB911CSW by TITAN

Getting started...
EN
07
Safety information
>Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
>Never hold the workpiece in your hands or across your
leg while cutting. Secure the workpiece to a stable
platform. It is important to support the work properly to
minimize body exposure, blade binding, or loss of control.
>Hold the power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a “live” wire will also make exposed metal
parts of the power tool “live” and could give the operator
an electric shock.
>When ripping, always use a rip fence or straight edge
guide. This improves the accuracy of cut and reduces
the chance of blade binding.
>Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades that
do not match the mounting hardware of the saw will run
off-centre, causing loss of control.
>Never use damaged or incorrect blade washers
or bolt. The blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation.
Further safety instructions for all saws - Kickback
causes and related warnings
>Kickback is a sudden reaction to a pinched, jammed or
misaligned saw blade, causing an uncontrolled saw to lift
up and out of the workpiece toward the operator.
>When the blade is pinched or jammed tightly by the kerf
closing down, the blade stalls and the motor reaction
drives the unit rapidly back toward the operator.
>Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the workpiece.
TTB911CSW by TITAN

08
Safety information
Getting started...
EN
Safety warnings
>If the blade becomes twisted or misaligned in the cut, the
teeth at the back edge of the blade can dig into the top
surface of the wood causing the blade to climb out of the
kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect
operating procedures or conditions and can be avoided
by taking proper precautions as given below.
>position your arms to resist kickback forces. Position
your body to either side of the blade, but not in line
with the blade. Kickback could cause the saw to jump
backwards, but kickback forces can be controlled by the
operator, if proper precautions are taken.
>When blade is binding, or when interrupting a cut
for any reason, release the trigger and hold the saw
motionless in the material until the blade comes to
a complete stop. Never attempt to remove the saw
from the work or pull the saw backward while the
blade is in motion or kickback may occur. Investigate
and take corrective actions to eliminate the cause of
blade binding.
>When restarting a saw in the workpiece, centre the
saw blade in the kerf so that the saw teeth are
not engaged into the material. If a saw blade binds,
it may walk up or kickback from the workpiece as the
saw is restarted.
>Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag under
their own weight. Supports must be placed under the
panel on both sides, near the line of cut and near the
edge of the panel.
TTB911CSW by TITAN

Getting started...
EN
09
Safety information
>Do not use dull or damaged blades. Unsharpened
or improperly set blades produce narrow kerf causing
excessive friction, blade binding and kickback.
>Blade depth and bevel adjusting locking levers
must be tight and secure before making cut. If blade
adjustment shifts while cutting, it may cause binding and
kickback.
>Use extra caution when sawing into existing walls or
other blind areas. The protruding blade may cut objects
that can cause kickback.
Safety instructions for circular saws with inner
pendulum guard - Lower guard function
Safety instructions for all saws - Cutting procedures
>
>Check the operation of the lower guard spring. If the
guard and the spring are not operating properly, they
must be serviced before use. Lower guard may operate
sluggishly due to damaged parts, gummy deposits, or a
build-up of debris.
>
Check the lower guard for proper closing before
each use. Do not operate the saw if the lower guard
does not move freely and close instantly. Never
clamp or tie the lower guard into the open position.
If the saw is accidentally dropped, the lower guard may
be bent. Raise the lower guard with the retracting handle
and make sure it moves freely and does not touch the
blade or any other part, in all angles and depths of cut.
The lower guard may be retracted manually only for
special cuts such as "plunge cuts" and "compound
cuts". Raise the lower guard by the retracting
handle and as soon as the blade enters the material,
the lower guard must be released. For all other
sawing, the lower guard should operate automatically.
TTB911CSW by TITAN

Safety information
Getting started...
EN
10
Safety warnings
>Always observe that the lower guard is covering the
An
unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be aware
of the time it takes for the blade to stop after switch is
released.
Additional circular saw safety warnings
>Do not to use any abrasive wheels.
>Use only blade diameter(s) in accordance with the
>Follow the instructions for the blade changing procedure.
>Check the function of all blade guard operations.
>Only cut materials listed in the intended use.
>Use a dust collection system as described within this
instruction manual.
>Clean the product and guarding system properly and
regularly.
Saw blade safety warnings
>Only use saw blades if you have knowledge of how to
use and handle them.
>Pay attention to the maximum rotational speed. The
maximum rotational speed marked on the saw blade
shall not be exceeded.
>Do not use working saw blades which are cracked. Scrap
of saw blades which bodies are cracked. Repairing is not
permitted.
>Clamping surfaces shall be cleaned to remove dirt,
grease, oil and water.
>Do not use loose rings or sleeves to «make up» bore
sizes on saw blades.
>have the same diameter.
TTB911CSW by TITAN