TMG TMG-GH1230 User manual

▶WWW.TMGINDUSTRIAL.COM P0/18 Toll Free:1-877-761-2819

▶WWW.TMGINDUSTRIAL.COM P1/18 Toll Free:1-877-761-2819
Main specifications
Overall assembled size : L9.1 x W3.66 x H2.2 (m) / L30 x W12 x H7.2 (ft)
Shoulder height : H1.2 (m) / 4ft
Door : W1.2 x H1.8 (m) / 4 x 6 (ft)
Prior to assembly
Please read the instructions carefully before installation. It is important to follow your
local safety regulations and industry standards during installation. Regulations may
include but are not limited to :
Safety helmets, protective eyewear, and clothing
Safety harnesses for all elevated workers
Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part
number, please refer to the parts list to make sure you have all parts.
Choose a day with low or no wind to install, assembly is hard in heavy wind. Do not
make any alterations to the structure. Do not hang any weights on the frame during
installation, including parts. We are not responsible for any damages or injuries caused by
inappropriate installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
It is recommended to tape or add foam/rubber on the frame where joints connect and
where it touches the cover. This will help extend the life span of the cover.
Read the following item list carefully and count the number of items to ensure that all
parts are included prior to setup.

▶WWW.TMGINDUSTRIAL.COM P2/18 Toll Free:1-877-761-2819
TMG-GH1230 Part List
Parts
code
Graphical
Description
Length
Qty
1
Peak arch tube
φ32xL510mm
8
2
Upper rafter tube
φ32xL1404mm
16
3
Shoulder tube
φ32xL834mm
16
4
Sidewall tube
φ32xL668mm
16
5
Roof purlin
(horizontal tube)
φ25xL1330mm
35
6
Base plate
W95xL162mm
17
6A
Door column base plate
W95xL822mm
2
6B
Expansion bolt
φ14x100mm
38
7
Front door cross tubes
φ25xL1145mm
2
8
Rear door cross tubes
φ25xL1745mm
2
9
Upper vertical tubes for rear
truss
φ32xL1168mm
1
10
Lower vertical tubes for
rear truss
φ32xL964mm
1
11
Door frame cross pull tube
(front truss)
30x30xL1170mm
1
12
Door frame left tube
(front truss)
30x30xL1820mm
1
13
Door frame right tube
(front truss)
30x30xL1820mm
1
14
Door frame column left
tube
30x30xL1760mm
1
15
Door frame column right
tube
30x30xL1760mm
1
16
Door horizontal tube
30x30xL1090mm
4
17
Film rolling machine guide
tube
φ25xL1490mm
2

▶WWW.TMGINDUSTRIAL.COM P3/18 Toll Free:1-877-761-2819
18
Roll film tube
φ25xL1993mm
8
18A
Roll film tube
φ25xL1400mm
2
19
Tube clamp
φ32mm
6
20
Door buckle
1
21
Film rolling machine
2
22
Reed groove
L2000mm
38
22A
Clip spring
L2000mm
38
23
Eight clip spring
16
24
Pressure film carrier
φ25mm
16
25
Half round head bolt
M6x50mm
50
26
Hex bolt
M6x45mm
76
27
Hex bolt
M6x80mm
2
28
Self tapping screw
#12x25mm
206
28A
Self tapping screw
#12x35mm
4

▶WWW.TMGINDUSTRIAL.COM P4/18 Toll Free:1-877-761-2819
29
Self tapping screw
#12x35mm
78
30
Socket wrench
M8mm
1
30A
Hex wrench
φ4mm
1
31
Square plug
30x30mm
6
32
Round plug
φ25mm
6
33
Braided rope
φ8x25mm
1 bundle
34
Adhesive tape
10m
2 volume
35
Top cover film
W7.5xL10m
1
35A
Front and rear film
W5xL5m
2
36
Board
(not included)
44 meters

▶WWW.TMGINDUSTRIAL.COM P5/18 Toll Free:1-877-761-2819
Installation steps
Step 1 : Review the whole structure and choose the proper installation site.
Mark the ground in the final building location with a line showing the positions of
base plates, front doors. All lines should be drawn from center to center of all base
plate tubes. Diagonal line X must be equal to Y.
Base plates: all base plates must be installed firmly with expansion bolts (#6B) on
this step.
Figure 1
No.
Part
Qty
6
17
6A
2
6B
38

▶WWW.TMGINDUSTRIAL.COM P6/18 Toll Free:1-877-761-2819
Step 2 : Assemble all trusses.
The building includes 8 trusses , Connect all pipes with hex bolt (#26).
Figure 2
No.
Part
Qty
No.
Part
Qty
1
8
4
16
2
16
26
48
3
16

▶WWW.TMGINDUSTRIAL.COM P7/18 Toll Free:1-877-761-2819
 Lay down all (8) trusses on the ground when the assembly is all completed
and before moving to next step, and then wrap (#34) around the sharp points
of the joint to avoid friction between the fabric and the interface, resulting in
fabric damage.
Figure 3
No.
Part
Qty
34
1
Step 3 : Put up all trusses (refer to figure 4).
 Put up the truss, use hex bolt (#26) to secure the truss to the base plates.
Figure 4

▶WWW.TMGINDUSTRIAL.COM P8/18 Toll Free:1-877-761-2819
 Connect all purlins, and then wrap (#34) around the sharp points.
Figure 5
No.
Part
Qty
No.
Part
Qty
5
35
26
16
25
40
34
1

▶WWW.TMGINDUSTRIAL.COM P9/18 Toll Free:1-877-761-2819
Step 4 : Installation of front and rear trusses.
 Installation of the front truss.
Figure 6
No.
Part
Qty
No.
Part
Qty
7
2
16
4
11
1
19
4
12
1
25
10
13
1
26
8
14
1
31
6
15
1

▶WWW.TMGINDUSTRIAL.COM P10/18 Toll Free:1-877-761-2819
 Installation of the rear truss.
Figure 7
No.
Part
Qty
No.
Part
Qty
8
2
19
2
9
1
26
4
10
1

▶WWW.TMGINDUSTRIAL.COM P11/18 Toll Free:1-877-761-2819
Step 5 : Install boards (#36) and reed groove (#22) (refer to figure 8, figure 9).
 Fix the board (# 36) with self tapping screw (# 29).
 Fix the reed groove (# 22) with the self tapping screw (# 28).
Figure 8

▶WWW.TMGINDUSTRIAL.COM P12/18 Toll Free:1-877-761-2819
Figure 9
No.
Part
Qty
No.
Part
Qty
22
38
29
78
28
190
36
44

▶WWW.TMGINDUSTRIAL.COM P13/18 Toll Free:1-877-761-2819
Step 6 : Install the film.
 Install the front film.
Figure 10
No.
Part
Qty
No.
Part
Qty
20
1
28A
4
22A
11
35A
1

▶WWW.TMGINDUSTRIAL.COM P14/18 Toll Free:1-877-761-2819
 Install the rear film.
Figure 11
No.
Part
Qty
22A
6
35A
1

▶WWW.TMGINDUSTRIAL.COM P15/18 Toll Free:1-877-761-2819
 When you are ready to install the roof cover, unpack the cover and position it
parallel to the building frame on one side. the cover must be pulled over the
top of the truss frame without being snagged or stressed on any frame
members. tighten the film evenly to eliminate wrinkles and make the film flat
and smooth. Do not over-tighten during the adjustment process, otherwise it
will cause unnecessary damage. At this time, you can install a clip spring
(#22A) to fix the film.
Figure 12
No.
Part
Qty
22A
21
35
1

▶WWW.TMGINDUSTRIAL.COM P16/18 Toll Free:1-877-761-2819
Step 7 : Install roll film system.
 Install the roll film tube(#18), add a round plug(#32) at the end. the film (# 35)
is wound on a roll film tube , and clamped with a pressure film carrier (# 24).
Figure 13
No.
Part
Qty
No.
Part
Qty
18
8
28
16
18A
2
32
2
24
16

▶WWW.TMGINDUSTRIAL.COM P17/18 Toll Free:1-877-761-2819
 A round plug (# 32) is put on both ends of the film rolling machine guide tube (#
17), and the guide tube is mounted on the frame with a hex bolt (# 27), and it is
required to swing freely. The film rolling machine (# 21) drives the roll film tube
(# 18) to be raised and lowered horizontally and flexibly without jamming.
 Install the eight clip spring (# 23) and fasten the braided rope (# 33)
Figure14
No.
Part
Qty
No.
Part
Qty
17
2
27
2
21
2
32
4
23
16
33
1

▶WWW.TMGINDUSTRIAL.COM P18/18 Toll Free:1-877-761-2819
After the Installation
Walk around and inspect the shelter periodically to make sure all components are
still firmly secured and the whole shelter is well supported. Check all bolts and nuts
as well as all connection points to make sure they are all in good position.
We strongly recommend you remove any snow from the roof immediately. Do not
leave any snow load on the roof overnight. Keep 3 feet of clearance on all sides at
all times. Do not allow snow to accumulate and pile up on the sides of the building.
Otherwise the pressure from the sides will push inwards and could lead to a
collapse.