TMG TMG-GH1240 User manual

www.tmgindustrial.com 0/18 Toll Free:1-877-761-2819

www.tmgindustrial.com 1/18 Toll Free:1-877-761-2819
MAIN SPECIFICATIONS :
Overall assembled size : L11.7 x W3.66 x H2.2 (m) / L38 x W12 x H7.2 (ft)
Shoulder height : H1.2 (m) / 4 ft
Door : W1.2 x H1.8 (m) / 4 x 6 (ft)
PRIOR TO ASSEMBLY
Please read the instructions carefully before installation. It is important to follow your local safety regulations and
industry standards during installation. Regulations may include but are not limited to :
- Safety helmets, protective eyewear, and clothing
- Safety harnesses for all elevated workers
- Proper ladder, cage, and safety operation
Check all components and parts before installation. All parts are marked with a part number, please refer to the parts list
to make sure you have all parts.
Choose a day with low or no wind to install, assembly is hard in heavy wind. Do not make any alterations to the structure.
Do not hang any weights on the frame during installation, including parts. We are not responsible for any damages or
injuries caused by inappropriate installation, unauthorized modifications or extreme weather.
This building is not intended for human occupancy.
It is recommended to tape or add foam/rubber on the frame where joints connect and where it touches the cover. This
will help extend the life span of the cover.
Read the following item list carefully and count the number of items to ensure that all parts are included prior to setup.

www.tmgindustrial.com 2/18 Toll Free:1-877-761-2819
TMG-GH1240 PART LIST
PARTS
CODE
GRAPHICAL
DESCRIPTION
QTY
1
Peak arch tube
10
2
Upper rafter tube
20
3
Shoulder tube
20
4
Sidewall tube
20
5
Roof purlin
(horizontal tube)
45
6
Base plate
21
6A
Door column base plate
2
6B
Expansion boltφ14x100mm
46
7
Front door cross tubes
2
8
Rear door cross tubes
2
9
Upper vertical tubes for rear truss
1
10
Lower vertical tubes for rear truss
1
11
Door frame cross pull tube
(front truss)
1
12
Door frame left tube
(front truss)
1

www.tmgindustrial.com 3/18 Toll Free:1-877-761-2819
13
Door frame right tube
(front truss)
1
14
Door frame column left tube
1
15
Door frame column right tube
1
16
Door horizontal tube
4
17
Film rolling machine guide tube
2
18
Roll film tube
10
18A
Roll film tube
2
19
Tube clamp
6
20
Door buckle
1
21
Film rolling machine
2
22
Reed groove
44
22A
Clip spring
44
23
Eight clip spring
20
24
Pressure film carrier
20
25
Half round head bolt M6x50
60

www.tmgindustrial.com 4/18 Toll Free:1-877-761-2819
26
Hex bolt M6x45
92
27
Hex bolt M6x80
2
28
Self tapping screw #12x25
240
28A
Self tapping screw #12x35
4
29
Self tapping screw #12x35
94
30
Socket wrench
1
30A
Hex wrench
1
31
Square plug
6
32
Round plug
6
33
Braided rope
1
bundle
(30m)
34
Adhesive tape
2
35
Top cover film
1
35A
Front and rear film
2
36
Board
(not included)
56
meters

www.tmgindustrial.com 5/18 Toll Free:1-877-761-2819
INSTALLATION STEPS
STEP 1 : REVIEW THE WHOLE STRUCTURE AND CHOOSE THE PROPER INSTALLATION SITE.
Choose a solid flar level ground area to set up the building. Do not install the building on soft ground, uneven
surfaces, sloped surfaces.
We strongly recommend that you build the structure on a solid foundation such as cement and use anchor bolts
on all base plates.
Be ware of the surrounding area. Do not set up the building near snowdrifts. open flames or exposed electrical
wires. Do not keep heat sources near the fabric cover. Keep the building surroundings clear at all times.
Mark the ground in the final building location with a line showing the positions of base plates, front doors. All
lines should be drawn from center to center of all base plate tubes. Diagonal line X must be equal to Y.
Base plates: all base plates must be installed firmly with expansion bolts (#6B) on this step.
Installation diagram of expansion bolt.
NO.
PART
QTY
NO.
PART
QTY
6
21
6B
46
6A
2

www.tmgindustrial.com 6/18 Toll Free:1-877-761-2819
STEP 2 : ASSEMBLE ALL TRUSSES.
The building includes 10 trusses , Connect all pipes with hex bolt (#26).
NO.
PART
QTY
NO.
PART
QTY
1
10
4
20
2
20
26
60
3
20

www.tmgindustrial.com 7/18 Toll Free:1-877-761-2819
 Lay down all (10) trusses on the ground when the assembly is all completed and before moving to next
step, and then wrap (#34) around the sharp points of the joint to avoid friction between the fabric and
the interface, resulting in fabric damage.
NO.
PART
QTY
34
1

www.tmgindustrial.com 8/18 Toll Free:1-877-761-2819
STEP 3 : PUT UP ALL TRUSSES.
 Put up the truss, use hex bolt (#26) to secure the truss to the base plates.
Connect all purlins, and then wrap (#34) around the sharp points.
NO.
PART
QTY
NO.
PART
QTY
5
45
26
20
25
50
34
1

www.tmgindustrial.com 9/18 Toll Free:1-877-761-2819
STEP 4 : INSTALLATION OF FRONT AND REAR TRUSSES.
 Installation of the front truss.
NO.
PART
QTY
NO.
PART
QTY
7
2
16
4
11
1
19
4
12
1
25
10
13
1
26
8
14
1
31
6
15
1

www.tmgindustrial.com 10/18 Toll Free:1-877-761-2819
 Installation of the rear truss.
NO.
PART
QTY
NO.
PART
QTY
8
2
19
2
9
1
26
4
10
1

www.tmgindustrial.com 11/18 Toll Free:1-877-761-2819
STEP 5 : INSTALL BOARDS (#36) AND REED GROOVE (#22)
Fix the board (# 36) with self tapping screw (# 29).
Fix the reed groove (# 22) with the self tapping screw (# 28).

www.tmgindustrial.com 12/18 Toll Free:1-877-761-2819
NO.
PART
QTY
NO.
PART
QTY
22
44
29
94
28
220
36
56

www.tmgindustrial.com 13/18 Toll Free:1-877-761-2819
STEP 6 : INSTALL THE FILM.
 Install the front film.
NO.
PART
QTY
NO.
PART
QTY
20
1
28A
4
22A
11
35A
1

www.tmgindustrial.com 14/18 Toll Free:1-877-761-2819
 Install the rear film.
NO.
PART
QTY
22A
6
35A
1

www.tmgindustrial.com 15/18 Toll Free:1-877-761-2819
 When you are ready to install the roof cover, unpack the cover and position it parallel to the building frame on
one side. the cover must be pulled over the top of the truss frame without being snagged or stressed on any
frame members. tighten the film evenly to eliminate wrinkles and make the film flat and smooth. Do not
over-tighten during the adjustment process, otherwise it will cause unnecessary damage. At this time, you can
install a clip spring (#22A) to fix the film.
NO.
PART
QTY
22A
27
35
1

www.tmgindustrial.com 16/18 Toll Free:1-877-761-2819
STEP 7 : INSTALL ROLL FILM SYSTEM.
 Install the roll film tube(#18), add a round plug(#32) at the end. the film (# 35) is wound on a roll film tube ,
and clamped with a pressure film carrier (# 24).
NO.
PART
QTY
NO.
PART
QTY
18
10
28
20
18A
2
32
2
24
20

www.tmgindustrial.com 17/18 Toll Free:1-877-761-2819
 Around plug (# 32) is put on both ends of the film rolling machine guide tube (# 17), and the guide tube is
mounted on the frame with a hex bolt (# 27), and it is required to swing freely. The film rolling machine (# 21)
drives the roll film tube (# 18) to be raised and lowered horizontally and flexibly without jamming.
 Install the eight clip spring (# 23) and fasten the braided rope (# 33)
NO.
PART
QTY
NO.
PART
QTY
17
2
27
2
21
2
32
4
23
20
33
1

www.tmgindustrial.com 18/18 Toll Free:1-877-761-2819
AFTER THE INSTALLATION
Walk around and inspect the shelter periodically to make sure all components are still firmly secured and the whole shelter
is well supported. Check all bolts and nuts as well as all connection points to make sure they are all in good position.
We strongly recommend you remove any snow from the roof immediately. Do not leave any snow load on the roof
overnight. Keep 3 feet of clearance on all sides at all times. Do not allow snow to accumulate and pile up on the sides of
the building. Otherwise the pressure from the sides will push inwards and could lead to a collapse.