Toastmaster TC17A Quick start guide

ENGLISH
page 1
FRANÇAIS
page 5
ESPAÑOL
página 9
1
Middleby Cooking Systems Group  1400 Toastmaster Drive  Elgin, L 60120  [phone]  FAX [phone]
© 2001 Toastmaster, A Middleby Company.
is a registered trademark of Toastmaster, A Middleby Company. All rights reserved.
TC17A/TC21A
Domestic and Std. Export
ENGLISH/French/Spanish
P/N 45067
Rev. B  V1  1/01
WARNING: IN CASE OF FIRE
Disconnect the toaster from its power source IM-
MEDIATELY. This allows the unit to cool, making it
easier to put out the fire.
WARNING
F R Y UR SAFETY D N T ST RE R USE
GAS LINE R THER FLAMMABLE VAP RS
R LIQUIDS IN THE VICINITY F THIS R ANY
THER APPLIANCE
WARNING
IMPR PER INSTALLATI N, ADJUSTMENT, AL-
TERATI N, SERVICE R MAINTENANCE CAN
CAUSE PR PERTY DAMAGE, INJURY R
DEATH. READ THE INSTALLATI N AND PER-
ATING INSTRUCTI NS TH R UGHLY BEF RE
INSTALLING R SERVICING THIS EQUIPMENT.
WARNING
Do not operate the conveyor toaster on either of its
sides, on its rear surface, or without legs. Prema-
ture failure of the heating elements will occur.
WARNING
Disconnect the toaster from its electrical power
supply before cleaning or servicing.
CAUTION
Using any parts other than genuine Toastmaster factory parts
relieves the manufacturer of all liability.
IMPORTANT
Contact your authorized service agent to perform maintenance
and repairs. A service agency directory is supplied with your
toaster.
IMPORTANT
Toastmaster (manufacturer) reserves the right to change speci-
fications and product design without notice. Such revisions do
not entitle the buyer to corresponding changes, improvements,
additions or replacements for previously purchased equipment.
RETAIN THIS MANUAL FOR FUTURE REFERENCE
This manual provides detailed information for the installation
and operation of your toaster. t also contains information to
assist the operator in diagnosing problems in the event of a
malfunction. This manual is an important tool for the operator
and should be kept readily available.
I. DESCRIPTION AND SPECIFICATIONS
A. Component Location
The major components of the toaster are shown in Figure 1
below.
7. Return tray
1. ON/OFF/STBY
knob
6. Conveyor
2. Conveyor speed
contro knob
B. Component Function (see Fi ure 1)
1-3. Toaster control knobs - see Section , Operation.
4. Crumb tray - Collects crumbs from the toasted product. The
tray can be removed for cleaning.
5. Entry rack - Loaded with the bakery product to be toasted. The
product then slides onto the conveyor. The entry rack can be
removed for cleaning.
6. Conveyor - Transports the bakery product through the toaster,
between the top and bottom heating elements.
7. Return tray - Collects the toasted product. The tray can be
removed for cleaning.
C. Operatin and Electrical Specifications
Pre-Heat Time: 15 minutes
Electrical Specifications/TC17 toaster models:
 TC17A74: 120V, 50/60 Hz, 1 Ph, 1.97kW, 16.4A, NEMA 5-20P plug
 TC17A63: 208V, 50/60 Hz, 1 Ph, 2.62kW, 12.6A, NEMA 6-15P plug
 TC17A66: 240V, 50/60 Hz, 1 Ph, 2.62kW, 11.0A, NEMA 6-15P plug
Electrical Specifications/TC21 toaster models:
 TC21A63: 208V, 50/60 Hz, 1 Ph, 2.90kW, 13.9A, NEMA 6-20P plug
 TC21A66: 240V, 50/60 Hz, 1 Ph, 2.90kW, 12.1A, NEMA 6-20P plug
NOTE
Electrical wiring diagrams are provided at the back of this Manual.
Fi ure 1
Conveyor Toaster
Models TC17A, TC21A
OWNER'S OPERATING AND
INSTALLATION MANUAL
4. Crumb tray
5. Entry rack
3. Top and Bottom
temperature
contro knobs

2
ENGLISH
II. INSTALLATION
IMPORTANT
IT IS THE CUSTOMERS RESPONSIBILITY TO REPORT ANY
CONCEALED OR NON-CONCEALED DAMAGE TO THE FREIGHT
COMPANY.
A. Assembly
1. Thread the 4 (102mm) legs into the four holes on the bottom of
the toaster. See Figure 2. Then, place the toaster in the desired
location.
2. nstall the entry rack and crumb tray into the front of the toaster,
as shown in Figure 2.
Fi ure 2 - Basic assembly and front-exit confi uration
Legs (4)
thread into ho es
in bottom of
toaster
Entry rack
hanger rods fit
into ho es on
toaster body
Crumb tray
s ides into opening
in front of toaster
Return tray
s ides underneath
toaster
Fi ure 3 - Electrical connection and rear-exit confi uration
3. TOASTERS NTENDED FOR FRONT-EX T OPERAT ON
ONLY:
Position the return tray underneath the toaster, as shown in
Figure 2. Note that the return tra extends past the FRONT of
the toaster in the front-exit configuration.
4. TOASTERS NTENDED FOR STRA GHT-THROUGH, REAR-
EX T OPERAT ON ONLY:
 Remove the CENTER screw from the rear panel of the
toaster, as shown in Figure 3.
 Push the rear panel forward into the toaster.
 Position the return tray underneath the toaster as shown
in Figure 3. Note that the return tra extends past the
REAR of the toaster in the rear-exit configuration.
2. Adjust
pane
1. Remove
screw
Return tray
s ides underneath
toaster
B. Electrical Utility Connection
IMPORTANT
THE ELECTRICAL CONNECTION TO THE TOASTER REQUIRES A
CIRCUIT BREAKER/FUSED DISCONNECT. ELECTRICAL SPECIFI-
CATIONS ARE LISTED ON THE SERIAL PLATE (SHOWN IN FIG-
URE 3), AND IN THE ELECTRICAL SPECIFICATIONS ON PAGE 1
OF THIS MANUAL.
CONSULT ALL APPLICABLE NATIONAL AND LOCAL CODES FOR
FURTHER ELECTRICAL CONNECTION REQUIREMENTS.
1. Before proceeding with the electrical connection, check the
following:
a. Check that the electrical supply matches the toasters
requirements. Refer to the toasters serial plate (Figure 3)
and to the Electrical Specifications on Page 1.
b. Check that the appropriate receptacle is available for the
power cord plug.
WARNING
ENSURE THAT BOTH THE CIRCUIT BREAKER/FUSED DIS-
CONNECT AND THE ON/OFF/STBY KNOB ARE IN THE OFF
POSITION BEFORE PROCEEDING. ENSURE THAT ANY
PACKING MATERIAL RESIDUE HAS BEEN REMOVED FROM
INSIDE THE TOASTING CHAMBER.
2. nsert the power cord plug into its receptacle.
Seria
p ate
Fi ure 4
1. ON/OFF/STBY
knob
2. Conveyor
speed contro
knob
3. Top and Bottom
temperature
adjustment knobs
III. OPERATION
A. Location and Function of Controls
This section provides a basic description of the toaster controls, their
location, and the functions they perform. The operator MUST be familiar
with the controls. Refer to Figure 4.
1. ON/OFF/STBY knob
 When set to ON, turns on the conveyor and elements.
 When set to OFF, turns off the conveyor and elements.
 When set to STBY, places the toaster in a standby mode
by reducing the power to the heating elements. This saves
power during idle periods and extends the life of the toasters
components. Switching the knob back to the ON position
will return the toaster to operating temperature within 5
minutes.
2. Conve or Speed control knob
Adjusts the speed of the conveyor belt.
 SLOW is the minimum speed setting.
 FAST is the maximum speed setting.
3. Top and Bottom temperature adjustment knobs
Adjusts the temperature of the heating elements. Two knobs are
provided so that the top and bottom heating element temperatures
can be adjusted independently. Turning one of the knobs to the
OFF position allows one-sided toasting (for bagels, etc.)
 LOW is the lowest temperature setting, which produces a
lighter toasting of the bakery product on its top or bottom.
 H GH is the highest temperature setting, which produces a
darker toasting of the bakery product on its top or bottom.

3
ENGLISH
C. Shutdown Procedure
1. Switch the ON/OFF/STBY knob to the OFF (O) position.
2. Wait for the toaster to cool. Note that the cooling fan will remain
in operation to allow the toaster to cool faster.
3. AFTER the cooling fan stops, disconnect electrical power to
the toaster at the circuit breaker/fused disconnect.
D. Clearin Jams
WARNING
NEVER INSERT YOUR HANDS INTO THE TOASTING
CHAMBER TO CLEAR A JAM. SERIOUS INJURY MAY
RESULT.
CAUTION
NEVER use a plastic object to clear a jam. If the toaster is not
completel cool, damage to the toaster ma result.
CAUTION
When clearing a jam, use care to avoid damaging the heating ele-
ments.
1. Switch the ON/OFF/STBY knob to the OFF (O) position.
2. Wait for the toaster to cool. Note that the cooling fan will remain
in operation to allow the toaster to cool faster.
3. AFTER the cooling fan stops, disconnect electrical power to
the toaster at the circuit breaker/fused disconnect.
CAUTION - HOT SURFACES
DO NOT ATTEMPT TO CLEAR THE JAM UNTIL THE
TOASTER HAS COOLED THOROUGHLY.
4. Carefully clear the jam using a long object as a probe. This
object should preferably be made of wood, which is less likely
to damage the heating elements.
E. Daily Cleanin
WARNING
WHEN CLEANING THE TOASTER, NEVER APPLY
ENOUGH LIQUID TO STAND IN PLACE ON THE UNIT. DO
NOT SPRAY, RINSE, OR SUBMERGE THE TOASTER.
EXCESSIVE MOISTURE IN THE UNIT WILL CAUSE A SE-
VERE ELECTRICAL HAZARD AND MAY OTHERWISE
DAMAGE THE TOASTER.
CAUTION
DO NOT clean our toaster using abrasive cleaners or pads. Both
will scratch and dull the finish.
1. With the conveyor running, use a brush to clean any crumbs off
the conveyor into the crumb tray.
2. Switch the ON/OFF/STBY knob to the OFF (O) position.
3. Wait for the toaster to cool. Note that the cooling fan will remain
in operation to allow the toaster to cool faster.
4. AFTER the cooling fan stops, disconnect electrical power to
the toaster at the circuit breaker/fused disconnect.
CAUTION - HOT SURFACES
DO NOT TOUCH HOT SURFACES ON THE TOASTER, OR
REACH INTO THE TOASTING CHAMBER, UNTIL THE UNIT
HAS COOLED THOROUGHLY.
5. Wipe the exterior of the toaster with a damp sponge or cloth
soaked in hot or warm detergent water. Wipe with a clean,
damp cloth to remove the excess detergent, and then wipe again
to dry the toaster.
6. Remove the crumb tray and the return tray from the toaster,
and empty them. Wash the trays in warm detergent water, and
rinse them.
CAUTION
Never remove the crumb tra while the conve or is moving.
7. Remove the entry rack from the toaster. Wash the rack in warm
detergent water, and rinse it.
8. Towel the trays and entry rack dry. Reassemble all parts onto
the toaster.
Load buns/bage s
CUT SIDE UP
for proper toasting
Fi ure 5
B. Operation Procedure
1. Restore electrical power to the toaster at the circuit breaker/fused
disconnect.
2. Switch the ON/OFF/STBY knob to the ON position.
3. Allow the toaster to pre-heat for at least 15 minutes.
4. Adjust the toasting time (if necessary) by turning the conveyor
speed control knob.
5. Adjust the heating element temperatures (if necessary) by turning
the Top and Bottom temperature adjustment knobs.
NOTE: For proper toasting of one-sided bakery products (bagels,
etc.), we recommend the following:
 Turn the Top temperature adjustment knob to the desired
setting to toast the cut side of the product.
 Turn the Bottom temperature adjustment knob to a lower
setting, or to the OFF position, as desired.
 Load the product onto the entry rack with the cut side facing
UP, as shown in Figure 5.
f the product is loaded cut-side down, reverse the Top and Bottom
temperature knob settings provided above. Note that if the product
is loaded cut-side down, the heat of the conveyor belt may cause
a slight streaking effect on the cut side of the bakery product.
5. Load the entry rack with the bakery product to be toasted. The
product will slide off the entry rack and onto the conveyor.
6. After toasting, remove the product from the return tray.
7. During inactive periods, switch the Product Selection knob to the
STBY position. This reduces the power to the heating elements
to save power during idle periods and extends the life of the
toasters components. Switching the knob back to the ON position
will return the toaster to operating temperature within 5 minutes.
Bottom temperature
adjustment knob set to a
ower setting or to OFF
Top temperature
adjustment knob
set as desired

ENGLISH
page 1
FRANÇAIS
page 5
ESPAÑOL
página 9
A Middleby Company
Toastmaster  1400 Toastmaster Drive  Elgin, L 60120  USA  [phone]  FAX [phone]
Middleby Corp 24-Hour Service Hotline [phone]
www.mi leby.com
Wiring Diagram - Model TC17A74 120V Toasters
Wiring Diagram - Models TC17A/21A63 208V Toasters, Models TC17A/21A66 240V Toasters
Switch Configuration - All Model TC17A and TC21A Toasters
TOP ELEMENT
BTM ELEMENT 1
BTM ELEMENT 2
CONVEYOR
SPEED CONTROL
TERMINAL
BLOCK
GND
MOTOR
FAN
TRANSFORMER
230V p : 115V s
ON/OFF/STBY
S ITCH BOTTOM
TEMPERATURE
ADJUSTMENT
S ITCH
TOP TEMPERATURE
ADJUSTMENT
S ITCH
COOL DO N
S ITCH
BTM ELEMENT 1
BTM ELEMENT 2
CONVEYOR
SPEED CONTROL
TERMINAL
BLOCK
GND
MOTOR
FAN
ON/OFF/STBY
S ITCH BOTTOM
TEMPERATURE
ADJUSTMENT
S ITCH
TOP TEMPERATURE
ADJUSTMENT
S ITCH
COOL DO N
S ITCH
TOP ELEMENT 1
TOP ELEMENT 2
OFF POSITION ON POSITION STBY POSITION