Topcom WBR 7011 B User manual

Wireless Broadband Router
WBR 7011b
QUICK INSTALLATION GUIDE
INSTALLATIE GIDS
GUIDE D’INSTALLATION RAPIDE
SCHNELLE INSTALLATIONSANLEITUNG
SNABBINSTALLATIONSGUIDE
HURTIG INSTALLATIONSGUIDE
HURTIGINSTALLASJON
PIKA-ASENNUSOHJEET
MANUAL DE USUARIO
MANUAL DO UTILIZADOR
V1.3
HL_7011b_front.fm Page 1 Thursday, August 19, 2004 4:09 PM

GB The features described in this manual are published with reservation to modifications.
NL De in deze handleiding beschreven mogelijkheden worden gepubliceerd onder voor-
behoud van wijzigingen.
FLes possibilités décrites dans ce manuel sont publiées sous réserve de modifications.
DDie in dieser Bedienungsanleitung umschriebenen Möglichkeiten, werden vorbehalt-
lich Änderungen publiziert.
SFunktionerna i denna bruksanvisning publiceras med reservation för ändringar.
DK Vi forbeholder os retten til ændringer af de specifikationer, der er beskrevet
i denne brugsanvisning.
NFunksjoner beskrevet i denne manualen kan endres uten nærmere informasjon.
SF Tässä ohjekirjassa julkaissut tiedot voivat muuttua ilman ennakkoilmoitusta.
ES Las características descritas en este manual pueden ser objeto de futuras modifica-
ciones.
PAs características descritas neste manual são publicadas sob reserva de poderem ser
modificadas.
This product is made by Topcom Belgium
FOR USE IN:
BELGIUM, HOLLAND, GERMANY, SWEDEN,
DENMARK, NORWAY, FINLAND, SPAIN, ITALY,
PORTUGAL, GREECE, TURKEY.
This product is in compliance with the essential requirements and other relevant provisions of the R&TTE directive 1999/5/EC.
The Declaration of conformity can be found on :
http://www.topcom.net/support/declarations/
Skr7011b.book Page 2 Thursday, August 19, 2004 11:17 AM

Topcom Wireless Broadband Router WBR 7011b 3
Topcom Wireless Broadband Router WBR 7011b
ENGLISH
1 THE CONNECTION PANEL
* POWER 12V DC: The power port is to connect the 12 V DC
(1000mA) power adapter.
--> The power LED on the front panel will go ON when the power
adapter is connected.
* WAN: The WAN Ethernet port is to connect your ASDL/Cable
modem.
--> The WAN LED will go ON if the network Ethernet cable is
properly connected.
*Ports 1- 4: This is to connect networked devices, such as PCs, ftp
servers or anything else you want to put on your network.
--> The LAN LED’s will indicate the connection status.
* Reset Button: If you would like to load default settings, press the
reset button and hold it for at least 4 seconds. It will load the factory
default settings for the device. Do not press the reset button unless
you want to clear the current data.
1Z VDC WAN Rese t
1234
Skr7011b.book Page 3 Thursday, August 19, 2004 11:17 AM

4Topcom Wireless Broadband Router WBR 7011b
Topcom Wireless Broadband Router WBR 7011b
2 CONFIGURING THE PC TO CONNECT TO
THE CABLE/DSL ROUTER
If you do not wish to set a static IP address on your PC, you will need to
configure your PC to accept the IP address that the router will provide.
1. Click Start button, select Settings, then Control Panel
2. Double-click the Network Icon
3. In the configuration windows, select the TCP/IP protocol line that
has been associated with your network card/adapter.
Remark:
- The routers default IP address is: 192.168.1.1
- DCHP server is ON
Skr7011b.book Page 4 Thursday, August 19, 2004 11:17 AM

Topcom Wireless Broadband Router WBR 7011b 5
Topcom Wireless Broadband Router WBR 7011b
ENGLISH
4. Click the Properties button, then choose the IP ADDRESS tab.
Select Obtain an IP address automatically.
5. Then select DNS configuration tab to add DNS IP address. Select
Disable DNS function. Press OK. You have completed the client
settings.
6. After clicking OK, windows will ask you to restart the PC. Click Yes.
Skr7011b.book Page 5 Thursday, August 19, 2004 11:17 AM

6Topcom Wireless Broadband Router WBR 7011b
Topcom Wireless Broadband Router WBR 7011b
3VERIFY YOUR PC’S IP CONFIGURATION
There are some tools which are great for finding out a computer’s IP
configuration: MAC address and default gateway.
• WINIPCFG (FOR WINDOWS 95/98)
Inside the windows 95/98/ME Start button, select Run and type
winipcfg. In the example below this computer has a IP address of
192.168.1.100 and the default gateway is 192.168.1.1. The default
gateway should be the broadband router IP address. The MAC address
in windows 95/98 is called the Adapter Address.
NOTE: You can also type winipcfg in the DOS command.
• IPCONFIG (FOR WINDOWS 2000/NT)
In the DOS command type IPCONFIG and press Enter. Your PC IP
information will be displayed as shown below.
Skr7011b.book Page 6 Thursday, August 19, 2004 11:17 AM

Topcom Wireless Broadband Router WBR 7011b 7
Topcom Wireless Broadband Router WBR 7011b
ENGLISH
- IPCONFIG / RENEW will renew the IP address, gateway and DNS.
• WINDOWS XP
Click the right mouse key on your network adapter and select Status
The support screen will display the IP information.
Skr7011b.book Page 7 Thursday, August 19, 2004 11:17 AM

8Topcom Wireless Broadband Router WBR 7011b
Topcom Wireless Broadband Router WBR 7011b
4 SETUP THE BROADBAND ROUTER
When your PC has a valid IP address, you should be able to go to the
router setup web page.
Open Internet Explorer or Netscape Navigater and goto address:
192.168.1.1
Now the login screen will appear.
--> Enter the username and password.
Skr7011b.book Page 8 Thursday, August 19, 2004 11:17 AM

Topcom Wireless Broadband Router WBR 7011b 9
Topcom Wireless Broadband Router WBR 7011b
ENGLISH
By default the username is admin and the password is admin.
--> Click OK to proceed.
Now you enter the web management of your Wireless Router.
Skr7011b.book Page 9 Thursday, August 19, 2004 11:17 AM

10 Topcom Wireless Broadband Router WBR 7011b
Topcom Wireless Broadband Router WBR 7011b
* Choose Quick Setup Wizard to start the configuration:
* In next screen you can set the Time Zone
- Set Time Zone: Please select your region
- Time Server Address: You can enter the IP address of your
prefered Time server or you can leave the default setting
- Daylight Savings: Here you can Enable the Daylight Savings.
Please enter the start and end date of the Daylight Savings.
--> Click Next to proceed
* Now choose your Broadband Connection Type:
- Cable Modem: Used for cable modem connections
Skr7011b.book Page 10 Thursday, August 19, 2004 11:17 AM

Topcom Wireless Broadband Router WBR 7011b 11
Topcom Wireless Broadband Router WBR 7011b
ENGLISH
-Host Name: Enter your Host Name if necessary.
-MAC Address: Some Cable Internet Providers will keep the
MAC address of your computer in there server. In this case you
should clone the Mac address of your computer. Click Clone
Mac Address to copy your computers Mac address into the
router.
--> Click OK to proceed.
- Fixed-IP xDSL: Used for cable modem or DSL bridge with fixed IP
address
- IP address assigned by your Service Provider: Please enter the
fixed WAN IP address.
- Subnet Mask: Enter the Subnet Mask.
- DNS Address: Enter the DNS address.
- Service Provider Gateway Address: Enter the Gateway IP
address.
--> Click OK to proceed.
- PPPoE xDSL: Used for DSL bridge with PPPoE connection.
Skr7011b.book Page 11 Thursday, August 19, 2004 11:17 AM

12 Topcom Wireless Broadband Router WBR 7011b
Topcom Wireless Broadband Router WBR 7011b
- Username: Enter your PPPoE username.
- Password: Enter your password.
- Service Name: Enter the servive name ( for example the name of
your Internet provider)
- MTU: Enter the MTU size (If the size is not specified by your Internet
Provider, please leave the default value at 1392)
- Connection Type:
* Continuous: The PPP-connection will always be active
* Connect on Demand: The PPP-connection will establish when a
computer is accessing the Internet. The PPP connection will
disconnect when there is no more Internet traffic during the Idle
Time (minutes), entered in the field below
* Manual: The PPP connection is established / disconnected
manually by clicking Connect / Disconnect.
--> Click OK to proceed.
- PPTP xDSL: used for cable modem or DSL bridge with PPTP
connection. PPTP can also be used when the router is connected to
another LAN network.
Skr7011b.book Page 12 Thursday, August 19, 2004 11:17 AM

Topcom Wireless Broadband Router WBR 7011b 13
Topcom Wireless Broadband Router WBR 7011b
ENGLISH
* WAN connection: DHCP client or Fixed IP address.
- Obtain an IP address automatically:
-Host Name: Enter your Host Name if necessary.
-MAC Address: Some Cable Internet Providers will keep the
MAC address of your computer in there server. In this case
you should clone the Mac address of your computer. Click
Clone Mac Address to copy your computers Mac address into
the router.
- Use the following IP address:
- IP address: Please enter the fixed IP address.
- Subnet Mask: Enter the Subnet Mask.
- Default Gateway: Enter the Gateway IP address.
*PPTP Settings:
- User ID: Enter the PPTP username.
Skr7011b.book Page 13 Thursday, August 19, 2004 11:17 AM

14 Topcom Wireless Broadband Router WBR 7011b
Topcom Wireless Broadband Router WBR 7011b
- Password: Enter the PPTP password.
- PPTP Gateway: Enter the Gateway.
- Connection ID: Enter the Connection ID when necessary.
- MTU: Enter the MTU size (If the size is not specified, please
leave the default value at 1392)
- BEZEQ-ISRAEL: Only for Israel
- Connection Type:
*Continuous: The PPP-connection will always be active
*Connect on Demand: The PPP-connection will establish
when a computer is accessing the Internet. The PPP
connection will disconnect when there is no more Internet
traffic during the Idle Time (minutes), entered in the field
below
*Manual: The PPP connection is established / disconnected
manually by clicking Connect / Disconnect.
--> Click OK to proceed.
- L2TP xDSL: Used for cable modems with L2TP connection.
Skr7011b.book Page 14 Thursday, August 19, 2004 11:17 AM

Topcom Wireless Broadband Router WBR 7011b 15
Topcom Wireless Broadband Router WBR 7011b
ENGLISH
*WAN connection: DHCP client or Fixed IP address.
- Obtain an IP address automatically:
- Host Name: Enter your Host Name if necessary.
- MAC Address: Some Cable Internet Providers will keep the
MAC address of your computer in there server. In this case you
should clone the Mac address of your computer. Click Clone
Mac Address to copy your computers Mac address into the
router.
- Use the following IP address:
- IP address: Please enter the fixed IP address.
- Subnet Mask: Enter the Subnet Mask.
- Default Gateway: Enter the Gateway IP address.
* L2TP Settings:
- User ID: Enter the L2TP username.
- Password: Enter the L2TP password.
- L2TP Gateway: Enter the Gateway.
- Connection ID: Enter the Connection ID when necessary.
- MTU: Enter the MTU size (If the size is not specified, please
leave the default value at 1392)
- Connection Type:
*Continuous: The PPP-connection will always be active
*Connect on Demand: The PPP-connection will establish
when a computer is accessing the Internet. The PPP
connection will disconnect when there is no more Internet
traffic during the Idle Time (minutes), entered in the field
below
*Manual: The PPP connection is established / disconnected
manually by clicking Connect / Disconnect.
- Telstra Big Pond: not for Europe
--> Click OK to proceed.
Now the quick setup wizard is finished.
Skr7011b.book Page 15 Thursday, August 19, 2004 11:17 AM

16 Topcom Wireless Broadband Router WBR 7011b
Topcom Wireless Broadband Router WBR 7011b
--> Click OK to finish.
Remark: the screen above will not appear if the router is configured by use of
a wireless PC.
Return to the home page by clicking “HOME” in the right top of the
screen.
5 CONNECTION STATUS
The WAN connection can be checked in the Status Info screen on the
router Web page.
Now click Internet Connection:
Skr7011b.book Page 16 Thursday, August 19, 2004 11:17 AM

Topcom Wireless Broadband Router WBR 7011b 17
Topcom Wireless Broadband Router WBR 7011b
ENGLISH
--> All information about the Internet connection will be visible: WAN
IP address, Gateway, DNS servers, ...
6WIRELESS SECURITY
To avoid that uninvited users will access your wireless network it is
strongly recommended to activate WEP (or WPA if available) encryption
of your wireless network.
--> Click General Setup in the home page of the router.
--> Now click Wireless to enter the Wireless Menu.
6.1 SSID, CHANNEL
Skr7011b.book Page 17 Thursday, August 19, 2004 11:17 AM

18 Topcom Wireless Broadband Router WBR 7011b
Topcom Wireless Broadband Router WBR 7011b
First of all you can change the name (ESSID) and channel of your
wireless network.
--> Choose Basic Settings
-Choose the wireless Mode: Access Point (AP) is default.
-ESSID: TOPCOM is default
- Choose the Channel Number: 1...13
--> Click Apply to confirm.
Note: Please make sure that the settings of your wireless adapter, connected
to your computer has the same channel and SSID as the Wireless Router.
6.2 ENCRYPTION
--> Choose Security to access the encryption menu.
Skr7011b.book Page 18 Thursday, August 19, 2004 11:17 AM

Topcom Wireless Broadband Router WBR 7011b 19
Topcom Wireless Broadband Router WBR 7011b
ENGLISH
By default the encryption is disabled. In this screen you can select your
type of encryption:
*Example: 64-bit WEP Encryption
- Encryption: choose WEP
- Key Length: 64 bit
- Key Format: It is recommended to choose HEX. Most Wireless
Adapters support HEX format.
- Default Tx Key: Choose a Key (1..4)
- Encryption Key #: Enter the above selected Key number.
--> In HEX-format you can use following caracters:
- 1 2 3 4 5 6 7 8 9 0
- a b c d e f or A B C D E F
Note: Please make sure that the settings of your wireless adapter, connected
to your computer has the same encryption settings as the Wireless Router.
Skr7011b.book Page 19 Thursday, August 19, 2004 11:17 AM

20 Topcom Wireless Broadband Router WBR 7011b
Topcom Wireless Broadband Router WBR 7011b
--> Click Apply to confirm.
6.3 HIDE THE ESSID
It is possible to make your wireless network invisible to unwanted users.
--> Choose Advanced Settings to access the Advanced Settings
menu.
-Broadcast ESSID: Select Disabled
--> Click Apply to confirm.
7 OTHER SETTINGS
For other settings, please refer to the full user guide on the provided CD.
Skr7011b.book Page 20 Thursday, August 19, 2004 11:17 AM