Tornador Classic User manual

Tornador® is a registered trademark of ECP Inc. ©2021
Tornador® covered by one or more of the following: U.S. Patent Nos. 6,883,732; 8,480,011; 8,690,077; 9,475,071; 10,182,696; 10,189,034; 10,343,177; 10,562,078; 10,730,062;
Taiwanese Patent No. I617360; U.S. Design Pat. Appl. Nos. 29/756,918; 29/756,919; 29/756,920; 29/756,921; 20150000705; 20150375272; Taiwan Application No. 103135808.
SAFETY REQUIREMENTS
Wear appropriate hearing and eye
protection. Use in well ventilated area. Do
not exceed 90 psi. Do not use with acidic,
ammable or combustible products; “USE
ONLY WITH TORNADOR®PRODUCTS.”
Do not point cleaning tool at face or body.
KEEP OUT OF REACH OF CHILDREN.
AIR REQUIREMENTS
The TORNADOR®cleaning tool requires
a minimum air pressure of 75 to 90 psi,
constant, for optimum performance.
DO NOT EXCEED 90 psi.
NOTE: Constant air supply may vary
depending on compressor size and
capabilities. Always make sure tank
and air lines are free from oil and water
contamination.
INSTRUCTIONS FOR USE
Cleaning Fabric
1. Remove large debris and vacuum area to be cleaned.
2. Turn liquid air valve to upright position to deliver cleaning solution.
3. Hold cleaning nozzle 1 to 3 inches from area to be cleaned. Fully depress trigger.
Begin with overlapping motion over area to be cleaned.
4. Next turn valve to down position using just air and dry the area.
Cleaning Dashboard and Hard Surfaces.
1. Recommended air pressure set at 75 psi
2. Turn liquid valve to straight up vertical position, using a overlapping motion, spray
area to be cleaned.
3. Allow cleaning liquid to remain on surface for 10 -15 seconds.
4. Follow with air only by turning valve to the horizontal down position. Begin drying
with overlapping motion followed with a soft dry towel.
Page 1 CONTINUED ON BACK PAGE

Tornador® is a registered trademark of ECP Inc. ©2021
Tornador® covered by one or more of the following: U.S. Patent Nos. 6,883,732; 8,480,011; 8,690,077; 9,475,071; 10,182,696; 10,189,034; 10,343,177; 10,562,078; 10,730,062;
Taiwanese Patent No. I617360; U.S. Design Pat. Appl. Nos. 29/756,918; 29/756,919; 29/756,920; 29/756,921; 20150000705; 20150375272; Taiwan Application No. 103135808.
TROUBLESHOOTING
PROBLEM:
• Tip will not oscillate
• Tip moves slowly
• Tip drips uid
• Will not dispense liquid
SOLUTION:
• Check for low air pressure
• Check for dirt build-up and clean
• Keep liquid valve in the horizontal position when not in use
• Check pickup tube for debris and rinse out
LIMITED WARRANTY
“90 day limited manufacturer’s warranty against manufacturing & part defects.” Warranty will be voided, if it is used
for anything other than the intended use of the Tornador®cleaning tool. Use of any products, other the Tornador®
products, with or in the Tornador®cleaning tool, voids warranty.
CARE & MAINTENANCE
1. Avoid dropping the gun on the oor, disconnect when not being used.
2. Turn liquid valve to the horizontal position after use to avoid dripping from tip.
3. Tighten the jar while holding the lid to avoid loosening or stripping gun assembly.
4. Keep the cone of the gun clean by removing the cone and rinsing frequently.
NOTE: After every use, place nozzle 2-3 inches into a bucket of soapy water while
depressing the trigger once or twice to quickly remove dirt buildup in the cone. This will
prevent premature wear.
Page 2