Toro Groundsmaster 1200 Series User manual

FormNo.3429-666RevA
FenderKit
Groundsmaster®1200SeriesPullBehindRotaryMower
ModelNo.139-3174
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
UseofthisproductmaycauseexposuretochemicalsknowntotheStateofCalifornia
tocausecancer,birthdefects,orotherreproductiveharm.
Safety
SafetyandInstructional
Decals
Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea
ofpotentialdanger.Replaceanydecalthatisdamagedormissing.
decal119-6807
119-6807
1.Warning—nostep
©2019—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3429-666*A

Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescriptionQty.Use
1Nopartsrequired–Preparethemachine.
Fender2
Supporttube2
Flange-headcapscrew(5/16x1-3/4
inches)4
2
Flangelocknut(5/16inch)4
Assemblethefenders.
3Nopartsrequired–Drilltheaxleframetube.
Capscrew(5/16x4inches)4
Washer(5/16inch)4
4Flangelocknut(5/16inch)4
Installthefendersontothemachine.
1
PreparingtheMachine
NoPartsRequired
Procedure
1.Connectthemachinetothetowvehicle;referto
theOperator'sManualforthemachine.
2.Lowerthemowerdecks;refertotheOperator’s
Manualforyourmachine.
3.Engagetheparkingbrakeforthetowvehicle,
shutofftheengine,removethekey,andwait
forallmovingpartstostopbeforeleavingthe
operator’sseat.
4.Chockthetiresofthemachine.
5.Lowerthejackandsupportthemachine;referto
theOperator'sManualforthemachine.
Important:Youmustfullysupportthe
weightofthemachinewiththejack.
6.Disconnectthemachinefromthetowvehicle.
2
AssemblingtheFenders
Partsneededforthisprocedure:
2Fender
2Supporttube
4Flange-headcapscrew(5/16x1-3/4inches)
4Flangelocknut(5/16inch)
Procedure
1.Assemblethesupporttubetothebracketofthe
fenderwith2ange-headcapscrews(5/16x
1-3/4inches)and2angelocknuts(5/16inch)
asshowninFigure1.
2

g282354
Figure1
1.Flange-headcapscrew
(5/16x1-3/4inches)
3.Supporttube
2.Bracket(fender)4.Flangelocknut(5/16inch)
2.Assembletheothersupporttubetotheother
fenderbracketwith2ange-headcapscrews
(5/16x1-3/4inches)and2angelocknuts(5/16
inch).
3.Torquethenutsandboltsto1978to2542N∙m
(175to225in-lb).
3
DrillingtheAxleFrame
Tube
NoPartsRequired
Procedure
g284106
Figure2
1.Holes(axleframetube)
Ifyourmachinedoesnothaveholesintheaxleframe
tube(Figure2)forthefenderkit,performthefollowing
steps:
1.Measure51mm(2inches)fromtheendofthe
axleframetube,andmarkthetubeasshown
inFigure3A.
3

g284109
Figure3
1.51mm(2inches)3.44.5mmm(1-3/4inches)
2.127mm(5inches)
2.Measure127mm(5inches)fromtheendofthe
axleframetube,andmarkthetubeasshown
inFigure3B.
3.Measure44.5mmm(1-3/4inches)fromthetop
oftheaxleframetube,andmarkthetubeas
showninFigure3C.
4.Centerpunchthemarkswheretheyintersect
(Figure4).
g284107
Figure4
1.11mm(7/16inch)drillbit
5.Drillthecenterpunchmarkswitha11mm(7/16
inch)drillbit(Figure4)throughbothwallsofthe
tube.
6.Repeatsteps1through5attheotherendofthe
axleframetube
4

4
InstallingtheFendersonto
theMachine
Partsneededforthisprocedure:
4Capscrew(5/16x4inches)
4Washer(5/16inch)
4Flangelocknut(5/16inch)
Procedure
1.Aligntheholesinthesupporttubefortheleft
fendertotheholesintheaxleframetubeas
showninFigure5.
Note:Ensurethatthedecalisalignedrearward
ofthefender-supporttube.
g282353
Figure5
1.Decal4.Capscrew(5/16x4
inches)
2.Axleframetube5.Washer(5/16inch)
3.Flangelocknut(5/16inch)6.Supporttube
2.Assemblethefender-supporttubetotheaxle
frametube(Figure5)with2capscrews(5/16x
4inches).2washers(5/16inch),and2ange
locknuts(5/16inch).
3.Torquethenutsandboltsto1978to2542N∙m
(175to225in-lb).
4.Repeatsteps1through3forthefenderatthe
othersideofthemachine.
5

Notes:

Notes: