Torque Fitness TANK User manual

TANK
Assembly Guide
PART #: 5548501-B
VERSION: XT1-102 & XTT1-101

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
ITEM PART NUMBER DESCRIPTION QTY
1 55414PA-F PTD ASSY, FRAME 1
2 5553001 WHEEL, 12" DIA X 3.5 WIDE 4
3 2011201 WASHER, STEEL 12.7 ID-40 OD-4 THK CLEAR ZINC 4
4 2010901 WASHER, M12 SPLIT LOCK 12
5 2011301-B SCREW, M12-1.75 X 30L SOC HD GR 12.9 CLEAR ZINC 4
6 5536101 ASSY, PUSH HANDLE-RH 2
7 5536001 ASSY, PUSH HANDLE-LH 2
8 2010801 WASHER, STEEL 12.7 ID-25 OD-2 THK CLEAR ZINC 8
9 2010701 SCREW, M12-1.75 X 83L SOC HD GR 12.9 CLEAR ZINC 8
10 5536201 ASSEMBLY, WEIGHT HORN 2
11 2010501 WASHER, STEEL 10.5 ID-20 OD-2 THK CLEAR ZINC 16
12 2010601 SCREW, M10-1.5 60L SOC HD GR 12.9 CLEAR ZINC 8
13 2012301 NUT, HEX LOCKING M10-1.5 GR 10 CLEAR ZINC 8
PAGE 2

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
1
2
3
4
5
ALIGN GROOVE
IN THE HUB WITH
THE ROLL PIN OF
THE AXEL
PAGE 3
SECURELY tighten all bolt connections.
STEP 1

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
1
6
7
6
7
9
4 8
PAGE 4
SECURELY tighten all bolt connections.
STEP 2

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
1
10
10
12
11
11
13
REMOVE TAG BEFORE
ASSEMBLING WEIGHT HORN
PAGE 5
SECURELY tighten all bolt connections.
STEP 3

2
3
4
5
REMOVE TIRE
STEP 4: RESISTANCE ADJUSTMENT
The resistance of the TANK is pre-set
at the factory. However if the resistance
needs to be increased or decreased please
follow the steps outlined in STEPS 4, 5, 6,
7, 10, 11 & 12.
PAGE 6

REMOVE HANDLE
PAGE 7
STEP 5: ADJUSTMENTS

REMOVE COVER
STEP 6: ADJUSTMENTS
PAGE 8

BRACKET
1. LOOSEN FOUR BOLTS
1/16"
1/16"
2. MOVE BRACKET 1/16" TO THE
LEFT FOR MORE RESISTANCE.
MOVE BRACKET 1/16" TO THE
RIGHT FOR LESS RESISTANCE.
3. RETIGHTEN FOUR
BOLTS
PAGE 9
STEP 7: RESISTANCE ADJUSTMENT

CHAIN
1. LOOSEN FOUR BOLTS
3. RETIGHTEN
FOUR BOLTS
2. TURN THIS BOLT CLOCKWISE
TO TIGHTEN CHAIN
TURN THIS BOLT COUNTER
CLOCKWISE TO LOOSEN CHAIN
STEP 8: CHAIN ADJUSTMENT
The chain tension is pre-set at
the factory. However if the chain
becomes too loose or is too tight,
please follow the steps outlined
in STEPS 4, 5, 6, 8, 10, 11 & 12.
PAGE 10

TO TENSION BELT, LOOSEN
NUT, PULL UP ON BRACKET
AND RETIGHTEN NUT
PAGE 11
STEP 9: BELT ADJUSTMENT
The belt tension on the TANK is
pre-set at the factory. However
if the belt needs to be re-tensioned,
please follow the steps outlined in
STEPS 4, 5, 6, 9, 10, 11 & 12.

SECURELY REASSEMBLE COVER
PAGE 12
STEP 10: ADJUSTMENTS

SECURELY
REASSEMBLE HANDLE
STEP 11: ADJUSTMENTS
PAGE 13

2
3
4
5
REASSEMBLE TIRE
PAGE 14
STEP 12: ADJUSTMENTS

SPROCKET SPROCKET
CHAIN
BELT
HANDLE BOLTS
WHEEL BOLTS
WEIGHT HORN BOLTS
PAGE 15
STEP 13: INSPECTION & LUBRICATION
PLEASE FOLLOW STEPS 4 - 6 & 10 - 12
INSPECTION:
Recommended tire inflation: 15 PSI
Once a month, check for loose bolts on handles
wheels and weight horns as indicated. Tighten if
necessary.
Once a month, check that the chain and sprockets are
clean, free of rust, dust and grime. Make sure that the
chain is properly lubricated. If chain is loose,
retighten chain as outlined in step 8.
Once a month, inspect belt. Make sure the belt is not
worn, frayed or loose. Replace belt if worn or frayed.
If belt is loose, re-tension belt as outlined in step 9.
LUBRICATION:
Once a month the sprockets should be cleaned and
the chain should be lubricated.
RECOMMENDED LUBRICATION: Use a Dry lubrication
for indoor use, and wet lubrication for outdoor use.
Most bicycle shops carry a variety of different
lubricants and can recommend a lubricant based on
the conditions where the TANK will be used.

PAGE 16
TANK PRODUCT LABELS - NOTICES