Toshiba TCB-SIR33UP-E User manual

‒1 ‒
(English)
Observe the safety precautions described in the Operation Manual of the Occupancy
sensor, Installation Manual and Operation Manual of the 4-way cassette type air
conditioner (indoor unit), or the installation manual supplied with the ceiling panel.
ACCESSORIES
Part Name Q’tyNo.
11
21
31
Occupancy sensor
CORD CLAMP
SCREW
Part Name Q’tyNo.
41
51
61
Operation Manual
Installation Manual
(this manual)
CD-ROM
HOW TO INSTALL THE OCCUPANCY SENSOR
ೈInstall the Occupancy sensor in correct orientation, since the Occupancy sensor
can be installed at only one corner as shown in (Fig. 1).
(Fig. 1)
Electrical control box Occupancy
sensor installing
position
Indoor unit
refrigerant pipe side
Indoor unit
drain pipe side
1. Remove the air inlet grille.
2. Remove the adjust corner cap at the corner where the Occupancy sensor is to
be installed. (Fig. 2)
• Pull the adjust corner cap in the direction of (1) and slide it in the direction of
(2) to remove it.
• Remove strap from the pin and detach the adjust corner cap from the ceiling
panel.
(1)
(2)
Ceiling panel
Adjust corner cap
(Fig. 2)
3. The insulation pad is packed in the two rectangular holes for ceiling panel wires.
Remove the insulation pad, and pass the wires from the occupancy sensor unit
through the rectangular holes. (Fig. 3)
4. Make sure that the black sponge wrapped around the wiring is about 20 mm out
of the rectangular hole on the indoor unit side, and fix it with 2CORD CLAMP
by 3SCREW. (Fig. 3)
20 mm
SCREW
CORD CLAMP
Pass the occupancy sensor lead wire
through the hole in the ceiling panel
Pull out the black sponge wrapped
around the wiring about 20 mm from
the rectangular hole.
Remove the insulation pad
from the rectangular hole on
the indoor unit side.
Pass the occupancy sensor lead
wire through the 2CORD CLAMP
and fix it with 3SCREW
(Fig. 3)
3
2
CAUTION
• If the black sponge is not properly positioned, water leakage, dew condensation,
and dew condensation on the wiring may occur, so be sure to do so.
5. Attach the sensor to the panel. At this time, be careful not to pinch the wiring.
(Fig. 4) If there is a part where the claws of the occupancy sensor unit are not
fitted, it may cause water leakage, so push claws A (2 places) and claws B
(3 places) firmly and firmly to make sure that the sensor part does not float.
please confirm.
There are claws B here,
so push it in firmly.
Push in the claw B (3 places) on the back
side of the Occupancy sensor so that
they fit.
Insert the claw A (2 places) of the sensor
part into the square holes of the panel in
the direction of the arrow.
Claw A
Claw A
Claw A
(Fig. 4)
CAUTION
• Press the two claws B of the adjust corner cap firmly as far as they will go, and
then check that the adjust corner cap is closely attached.
• Failure to do so may result in water leakage.
INSTALLATION MANUAL • Thank you for purchasing Occupancy sensor kit for TOSHIBA air conditioners.
• Read this manual carefully for correct installation of the Occupancy sensor before
starting work.
• After the installation is completed, execute a test run to check for normal operation
and explain how to use and maintain the Occupancy sensor to the customer
according to the Operation Manual.
Ask the customer to keep this manual with the Operation Manual.
To Qualified Installer in Installation Work and Service
Occupancy sensor kit
(for 4-Way cassette type)
Model: TCB-SIR33UP-E

‒2 ‒
HOW TO WIRING THE OCCUPANCY SENSOR
1. Remove the mounting screw A on the electric control box cover and loosen the
screw B. Slide the cover inward to remove the hook (the electric control box
cover remains hooked on the hinge).
Screw B
Screw A
Hook
Electric control
box cover Hinge
2. Connect the wiring from the Occupancy sensor to the connector 9P (CN214:
white) on the PC board of the indoor unit.
Use the cord clamp inside the electrical parts box to process the excess wiring,
and then attach the electric control box cover and air inlet grille.
Clamping claw
Plug into CN214
Cord
Clamp
NOTE
• If you do not connect the connector, the Occupancy sensor will not operate,
so be sure to connect it securely.
• Do not bundle these control signal wires with the power wire to avoid malfunction
CODE NO. (DN) SETTING
Wired remote controller (RBC-AMS5名E*)
Perform the advanced settings for the air conditioner. Carry out the setting operation
while the indoor unit is stopped. (Turn off the air conditioning unit before starting the
setting operation.)
6.Setting timer operation mode
Field setting menu(2/2)
Return
Set
7.DN setting
8.Reset power consumption data
Display example
of AMS55E*
1. Push the [ MENU] button to display the menu screen.
2. Push and hold the [ MENU] button and the [ ] button at the same time
to display the “Field setting menu”.
Push and hold the buttons for more than 4 seconds.
DN setting
Code
(DN) Data
Return
B5 0000
Fix
<>
DN setting
Code
(DN) Data
Return
B5 0001
Fix
<>
3. Push the [ ] / [ ] button to select “7. DN setting” on the “Field setting
menu” screen, then push the “ Set” [ F2] button.
The fan and louver of the indoor unit operate. When the group control is used, the
fan and louver of the selected indoor unit operate.
Move the cursor to select “DN code” with the “ <” [ F1] button, then
set “B5” with the [ ] / [ ] button.
Move the cursor to select “data” with the “ >” [ F2] button, then set
“0001” with the [ ] / [ ] button.
Return
Continue?
NoYes
DN setting
4. Push the [ MENU] button to set the other DN codes. After “Continue?” is
displayed on the screen.
5. Push the “ No” [ F2] button to finish the setting operation.
“” appears on the screen for a while, then the screen returns to the “Field setting
menu” screen.
Pushing the “ No” [ F2] button displays the unit selection screen
when the group control is used. Push the [ CANCEL] button on the unit
selection screen to finish the setting operation. “ ” appears on the screen for a
while, then the screen returns to the “Field setting menu” screen.
6. Push the [ CANCEL] button to return.
ABOUT THE OCCUPANCY SENSOR
• Sometimes the sensor may not detect people even when they are present if their
movements are small.
• If something having a difference in temperature with the surroundings moves, the
sensor may detect people as present even if they are not present.
• A wired remote controller (RBC-AMS5名E*) is required to use an occupancy sensor.
• Be sure to install an occupancy sensor in all indoor units if using group operation.
LIST OF SEPARATELY AVAILABLE PRODUCTS THAT
CANNOT BE USED WITH THE OCCUPANCY SENSOR
The following separately available products cannot be used together with the
Occupancy sensor.
Product name
Wireless receiver kit
Air purifier kit
Model
RBC-AXU33UP-E
TCB-EAPC1UHP-E, TCB-EAPC1UCP-E
1130615102